Nav TV RGB-VWv2 User manual

BHM
01/04/19
NTV-DOC339
1 | P a g e
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
RGB Power Harness
NTV-HAR324
Remote Control
NTV-REM004
3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]
www.nav-tv.com i[email protected]
RGB-VWv2
NTV-KIT906
Overview
The RGB-VWv2 adds an aftermarket backup camera to the factory navigation screen in select
Volkswagen vehicles. A secondary video input is included on the RGB module and can be
viewed at any time by supplying power to an input wire (optional).
Kit Content
RGB-VWv2
Video Harness
NTV-HAR335
RGB Converter
NTV-ASY254

BHM
01/04/19
NTV-DOC339
2 | P a g e
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
Power Harness
RGB Video Harness
Wire Side
Wire Side
RGB-VWv2 Interface Connectors
RGB-VWv2 Pin Out
PIN #
Description
Color
1
Ground (-)
Black
2
INPUT 2 (AUX VIDEO)
White/Blue
3
Shield (VIDEO 2)
Black
4
Signal (VIDEO 2)
Yellow
5
12v (+) ACC IN
Red
6
INTPUT 1 (CAM VIDEO)
White/Red
7
Shield (VIDEO 1)
Black
8
Signal (VIDEO 1)
Yellow
PIN #
Description
Color
1
RGB Ground
Black/Shield
2
SYNC (screen)
Gray
3
Blue Signal (screen)
Blue
4
Red Signal (screen)
Red
5
Green Signal (screen)
Green
6
RGB Ground
Shield
7
SYNC (radio/NAV)
Brown
8
Blue Signal (radio/NAV)
Purple
9
Red Signal (radio/NAV)
Orange
10
Green Signal (radio/NAV)
Yellow
IR Receiver
RGBS wires IN & OUT
Power, Video
IN & triggers
LED status
Brightness buttons

BHM
01/04/19
NTV-DOC339
3 | P a g e
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
RGB-VWv2 Installation
1. Remove the factory RNS navigation radio from the
dash.
2. Connect the provided RGB-VWv2 harness to the
RGB connector on the RNS radio.
3. Connect the other end of the harness to the RGBv2
module at the 10-PIN connector.
RGB-VWv2 Power Connections
1. From the provided RGB Power Harness, connect the black wire to chassis ground (-) and
the red wire with the white/blue wire to an ACC 12v (+) source (cigarette lighter, etc).
2. For VW, the reverse sensing is automatic through the radio. The VIDEO 2 RCA input
must be used for camera signal. NOTE: VW’s have no option for adding a secondary
(AUX) video source.
NOTE: VW’s must be programmed for reverse camera with a VAG-COMM (Ross Tech) in order to use this harness.

BHM
01/04/19
NTV-DOC339
4 | P a g e
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
RGB-VWv2 Remote Control / Brightness Setting
•The RGBv2 uses a (provided) remote for the following optional adjustments:
oArrow keys adjust (shifts) VIDEO 1 or 2 image LEFT, RIGHT, UP &
DOWN (OEM pass through image is not adjustable)
oZoom/Page arrows adjust brightness
oPressing MENU>MAP>BACK (in order) will default all settings.
•To adjust brightness of VIDEO 1 or 2 image, use the buttons
on the RGB side of the module and adjust to suit. NOTE:
when completing install, mount the RGBv2 module so that
the buttons are not being pressed.
RGB-VWv2 Operation
After all connections are properly made:
•When the vehicle is placed into reverse (white/red wire on the interface receives 12v +),
the navigation screen will switch to Video 1 source (reverse camera).
•In any other gear (but reverse) toggling the white/blue wire (12v (+) to the white/blue
wire) will switch the factory navigation screen to Video 2 source*.