Neilsen CT0957 User manual

BISCUIT JOINTER 100MM CT0957
ORIGINAL INSTRUCTIONS
SAVE THESE INSTRUCTIONS AND PRECAUTIONS.
READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE.

EC DECLARATION OF CONFORMITY
We CANNON TOOLS LTD
20 Station road, Rowley Regis, West Midlands,B65 0JU.U.K.
Declare that the design and construction of the following machine, in the form
supplied by us, comply with the requirements of the appropriate EC directives.
Product description: BISCUIT JOINTER 100MM
Model: CT0957
●EC-Machinery Directive 2006/42/EC
●EC-Directive on electromagnetic compatibility(EMC)2014/30/EU
Harmonized standards
EN 60745-1, EN 60745-2, EN 55014-1, EN 55014-2, EN61000-3-2, EN61000-3-3
CANNON TOOLS LTD
sign
Gurcharan Tony Singh Sanghera
2018-01-20
ENVIRONMENT
Should your appliance need replacement after extended use, do
not discard it with the household rubbish but dispose of it in an
environmentally safe way.
Waste produced by electrical machine items should not be
handled like normal household rubbish. Please recycle where
recycle facilities exist. Check with your Local Authority or retailer for
recycling advice.

FIG. A

1. DESCRIPTION
1
ON –OFF switch
10
Scale for the height
adjustment
2
Auxiliary handle
11
Base plate
3
Spindle lock
12
Dust bag connection
4
Angle stop
13
Dust bag
5
Scale for the fence angle
14
Motor base
6
Cutting depth adjustment knob
15
Plate protection
7
Clamping knob for angle adjustment
16
Lock-off button
8
Clamping knob for height adjustment
17
Blade (not visible)
9
Knob for height adjustment
Please inspect the product to ensure there is no damage and all parts have
been included prior to use.
2. TECHNICAL DATA
Voltage / frequency
230V/50Hz
Rated power
900W
No load speed
10800/min
Disc diameter
100mm
Blade bore diameter
22mm
Fine depth adjustment
3-10-12.3-19mm
Fence angle setting
00-900/ 900-1350
Spindle dimension
M10
Protection class
II
The power tools comes with a plug, the plug reach to BS1363/A standard,
with a 13Amp fuse.
WARNING! For your own safety, read this manual and the general
safety instructions carefully before using the appliance. Your power
tool should only be given to other users together with these
instructions.

3. SYMBOLS
The following symbols are used in this manual and/or on the machine:
Denotes risk of
personal injury or
damage to the tool
Read manual before
use
In accordance with
essential safety
standards of
applicable European
directives
Class II- The
machine is double
insulated; Earthing
wire is therefore no
necessary
Mandatory use of
eye protection
Wear a mask in
dusty conditions
Wear noise
protection
4. GENERAL POWER TOOL SAFETY WARNINGS
Read all safety warnings and instructions. Failure to heed warnings and
follow instructions may result in electric shock, fire and/or serious injury.
Keep safety warnings and instructions for future reference. The term
"power tool" in the safety warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
4.1 Working area
Keep working area clean and well lit. Untidy and dark areas can lead to
accidents.
Do not operate power tools in potentially explosive surroundings, for
example, in the presence of inflammable liquids, gases or dust. Power
tools create sparks which may ignite the dust or fumes
Keep children and bystanders at a distance when operating a power tool.

Distractions can cause you to lose control of it.
4.2 Electrical safety
Always check that the power supply corresponds to the voltage on
the rating plate.

Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use adapter plugs with earthed power tools. Unmodified plugs and
matching outlets will reduce the risk of a lethal electric shock.
Avoid body contact with earthed surfaces such as pipes, radiators,
kitchen ranges and refrigerators. There is an increased risk of a lethal
electric shock if your body is earthed.
Do not expose power tools to rain or wet conditions. If water gets inside a
power tool, it will increase the risk of a lethal electric shock.
Do not damage the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep the cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled cords increase the risk of
a lethal electric shock.
When operating a power tool outdoors, use an extension cable suitable
for outdoor use. Using a cord suitable for outdoor use reduces the risk of
a lethal electric shock.
If operating a power tool in a damp location is unavoidable, use a power
supply protected by a residual current device (RCD). Using an RCD
reduces the risk of a lethal electric shock.
4.3 Electrical safety
Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool when you are tired or
under the influence of drugs, alcohol or medication.Amoment of
inattention when operating a power tool may result in serious personal
injury.
Use safety equipment. Always wear eye protection. Using safety
equipment such as a dust mask, non-skid safety shoes, a hard hat, or
hearing protection whenever it is needed will reduce the risk of personal
injury.

Avoid accidental starts. Ensure the switch is in the off position before
inserting the plug. Carrying power tools with your finger on the switch or
plugging in power tools when the switch is in the on position makes
accidents more likely.
Remove any adjusting keys or spanners before turning on the power tool.
A spanner or key left attached to a rotating part of the power tool may
result in personal injury.
Do not reach out too far. Keep your feet firmly on the ground at all times.
This will enable you retain control over the power tool in unexpected
situations.
Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from the power tool. Loose clothes, jewellery or
long hair can become entangled in the moving parts.
If there are devices for connecting dust extraction and collection facilities,
please ensure that they are attached and used correctly. Using such
devices can reduce dust-related hazards.
4.4 Power tool use and care
Do not expect the power tool to do more than it can. Use the correct
power tool for what you want to do. Apower tool will achieve better results
and be safer if used in the context for which it was designed.
Do not use the power tool if the switch cannot turn it on and off. Apower
tool with a broken switch is dangerous and must be repaired.
Disconnect the plug from the power source before making adjustments,
changing accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
Store power tools, when not in use, out of the reach of children and do not
allow people who are not familiar with the power tool or these instructions
to operate it. Power tools are potentially dangerous in the hands of
untrained users.
Maintenance. Check for misalignment or jammed moving parts,
breakages or any other feature that might affect the operation of the
power tool. If it is damaged, the power tool must be repaired. Many
accidents are caused by using poorly maintained power tools.

Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to jam and are easier to control.
Use the power tool, accessories and cutting tools, etc., in accordance
with these instructions and in the manner intended for the particular type
of power tool, taking into account the working conditions and the work
which needs to be done. Using a power tool in ways for which it was not
intended can lead to potentially hazardous situations.
4.5 Service
Your power tool should be serviced by a qualified specialist using only
standard spare parts. This will ensure that it meets the required safety
standards.
5. SPECIFIC SAFETY WARNINGS
The machine only in technically perfect condition in accordance with, safety
and danger, and use! Disturbances which may affect safety, must be rectified
immediately!
It is generally prohibited to modify safety equipment of the machine or to
make ineffective!
The biscuit jointer is intended solely for milling wood or similar materials.
For a different or additional use and resulting property damage or injury takes
CANNON TOOLS no responsibility or warranty
6. ADJUSTMENTS
6.1 Adjusting the cutting depth
Move the motor base (14) as far as possible backwards.
Set the cutting depth by luring the cutting depth adjustment knob (6). The
knob is marked “0”, “2”, “4”, “5”, “7”, “12” and “19” according to the sizes
of dowels.
Move the motor base forwards and check if the pin will fall in the notch of
the adjustment knob.
6.2 Adjusting the cutting angle
The cutting angle can be set by unlocking the clamping knob (7} and put
the angle stop (4) in the required angle.

6.3 Adjusting the height
The correct height can be set by unlocking the clamping knob (8) and
turning the knob for the height adjustment (9) to the desired height with
aid of the scale (10)
The height must corresponds to half of the material thickness of the work
piece, the groove lot the biscuit dowel must always be in the middle of the
working piece
6.4 Checking the cutting depth
Always check the cutting depth after mounting a saw blade.
Disconnect the plug from the socket.
Move the motor base (14} as far as possible backwards.
Set the cutting depth in the maximum position by turning the depth
adjustment knob (6).
Move the motor base forwards till the pin will fall in the notch of the
adjustment knob (6)
Turn the saw blade till one tooth of the saw blade is in the front position.
Measure the distance from the side of the base plate to the tooth of the
saw blade.
Check if the distance is 19mm. The maximum position is 18mm.
6.5 Setting the cutting depth
When the cutting depth is not correct, it can be adjusted as following:
Move the motor base (14) as far as possible backwards
Loosen the Pin
Set the cutting depth by turning the screw, the screw is positioned at the
back of the pin.
Repeat the procedure till the cutting depth is correct.
Fasten the Pin.
7. ASSEMBLY
ATTENTION! Disconnect the power plug before carrying out any
adjustments or maintenance.

7.1 Mounting saw blade
Loosen your screws and open the top of the base plate
Press the spindle lock and turn the spindle until it engages in the lock.
Keep the spindle lock pressed during this procedure.
Remove the flange nut from the spindle using the wrench.
Position the saw blade and the flange.
Place the flange nut from the spindle and tighten it with the wrench.
Take care that the flange nut will be placed with the correct aide on the
spindle.
Release the spindle lock and check that the spindle is unlocked by
rotating it.
Close the top of the base plate and fasten four screws.
Make sure that the top of the base plate is securely closed before
operating the machine.
7.2 Mounting dust bag
For dust extraction the dust bag can be used. Insert the dust bag into the
vacuuming connection. Empty the dusts bag regularly so that the vacuuming
performance remains intact.
7.3 Attaching the plate protection
The plate protection needs to be attached to the angle stop prior to use. For
easier assembly, set the angle stop into the 90°position. Slide the plate
protection onto the angle stop with the plastic locating arms positioned over the
top, and the plastic face being located underneath.
8. OPERATION
8.1 Switching on and off.
Never use the spindle lock until the machine is working.
To switch the machine on push the lock-off button and the on/off switch
trigger at the same time.
To switch the machine off, release the on/off switch trigger.

Never use the spindle lock to stop the motor.
8.2 Marking the workpieces.
Before starling with the biscuit jointer the work pieces must be marked as
following:
Place the two work pieces which must be connected, on top of each
other.
Fasten the work pieces and mark the center of the groove.
The space between two grooves should be 10-15cm. This is not applicable for
smaller workpieces- smaller work pieces don't have to be marked.
8.3 Positioning of the machine
Based on the size of the work pieces the machine can be positioned in several
ways.
8.4 Large workpieces
Place the machine near the work piece
The middle of the base plate (this point is marked on the base plate) must
face the center of the groove in the work piece, {see marking the work
piece).
8.5 Small workpieces.
Place the machine near the work piece
The side of the machine must be lacing the side of the work piece.
8.6 Sawing grooves
Move the motor base backward.
Place the machine near the work piece.
Position the machine (see positioning of the machine)
Hold the machine with both hands and switch the machine on.
Push the motor base carefully forward as far as possible.
Move the motor base backward and switch the machine off.

8.7 Joining the workpieces
When the grooves in both work pieces have been made the workplaces can be
joined together
Put glue in both grooves.
Race the biscuit dowel in the groove of one work piece.
Place the other work piece on the biscuit dowel.
Fasten the work pieces and wait till the glue is dry.

9. CLEANING AND MAINTENANCE
Attention !Before performing any work on the equipment, pull
the power plug.
9.1 Cleaning
Keep the ventilation slots of the machine clean to prevent overheating of
the engine.
Regularly clean the machine housing with a soft cloth, preferably after
each use.
Keep the ventilation slots free from dust and dirt.
If the dirt does not come off use a soft cloth moistened with soapy water.
Never use solvents such as petrol, alcohol, ammonia water, etc. These
solvents may damage the plastic parts.
10.STORAGE
Thoroughly clean the whole machine and its accessories.
Store it out of the reach of children, in a stable and secure position, in a
cool and dry place, avoid too high and too low temperatures.
Protect it from exposure to direct sunlight. Keep it in the dark, if possible.
Don’t keep it in plastic bags to avoid humidity build-up.

CANNON TOOLS LTD
Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K.
Made in china