Neopost IS-5000 User manual

Installation Guide
IS-6000
Mailing Systems
with iMeterTM Postage Meter
IS-5000
4148787C/D - 01/02/2015

Safety Requirements1.
Please read this section carefully before connecting or using your equipment.
Power Connection
Before powering up your Mailing System, please check to ensure the system meets your
local AC voltage requirements (110V).
In addition to checking the power requirements, we also recommend that you:
•Use an outlet that is easily accessible.
•Do not route the power cord between pieces of furniture or over sharp edges.
•Avoid using outlets controlled by wall switches or shared by other equipment.
•Make sure the mailing system is close enough to the electric outlet that it leaves
plenty of slack on the power supply cord.
THIS EQUIPMENT MUST BE GROUNDED
•Only connect the power plug to an outlet provided with a
protective ground contact.
•To reduce the risk of fire, use only the power cord supplied
with the mailing system.
•Do not use ground adaptors.
•Do not use this product on a wet floor or near water.
•In case of liquid spillage, disconnect the power cord from the
outlet and proceed to cleaning.
To reduce the risk of fire, only connect the modem to the telephone
line using supplied cable (see System Specifications on page 347).
| Page 6 | mrt-25-2014 02:59 |

Compliance
Energy Star® Compliance
Office equipment is generally powered on 24 hours a day, so power management features
are important for saving energy and reducing air pollution.
Your Mailing System is an Energy Star® qualified Mailing System that automatically goes
into a low-power 'Sleep' mode after a period of inactivity.
Spending a large portion of time in low-power mode not only saves energy but helps your
equipment run cooler and last longer.
Environmental compliance
A program is implemented for the recycling of worn mailing systems at the end of their
lifetime. Contribute in a responsible way to the environmental protection by consulting your
retailer internet site, or by contacting him. He will inform you of the collection and treatment
processes of these machines.
CE compliance
Products presented in this guide conform to requirements of directives number 2006/95/CEE
and 2004/108/CEE.
This is a class A product. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
| Page 7 | mrt-25-2014 02:59 |

System Sleep Mode
Your Mailing System is Energy Star® qualified and automatically goes into a low-power
'Sleep' mode after a period of inactivity.
A very low-power 'Sleep' mode, called 'Soft-off' is also available.
•The Mailing System will automatically switch to 'Sleep' mode after 5 minutes of
non-activity. The Supervisor can change this 5-minute default setting.
•The Mailing System can be set to 'Sleep' mode manually by a short press on the
Sleep/Wake button.
•The Mailing System can be set to 'Soft-off' mode manually by a long press on the
Sleep/Wake button.
The light located on the display indicates:
- Amber (continuous): the Mailing System is in Sleep mode (low power mode).
- Amber (blinking): the Mailing System is in Soft-off mode (very low power mode).
- Green: the Mailing System is in Wake up mode and ready for use.
SLEEP / WAKE KEY
The Sleep/Wake key is located at the top right corner
of the control panel.
Wakes the Mailing System up or turns it to 'Sleep' or
'Soft-off' mode.
Sleep/wake
| Page 31 | mrt-25-2014 02:59 |
How to Switch Between 'Sleep' And 'Wake' Modes
1. Press the Sleep/Wake key to switch between “Sleep” and “Wake” modes.
To avoid weighing errors, make sure the Weighing Platform is clear
when you Wake up the machine.

2. General Specifications
Base
•Dimensions (Width x Length x Height): 25.19" x 10.74" x 13.42"
•Weight : 45.20 lb
•Power supply : 120 V (+/- 10 %) 3 prong
•Frequency : 60 Hz
•Maximum Input Power : 294W
•Ambient Temperature : + 50 °F to 104 °F
•Relative Humidity : 20 % to 80 % relative humidity (without condensation).
Feeder
•Dimensions (Width x Length x Height): 18.11" x 31.49" x 13.77"
•Weight : 63.93 lb
•Power supply : 120 V (+/- 10 %) 3 prong
•Frequency : 60 Hz
•Maximum Current Rating : 5A
•Ambient Temperature : 50 °F to 104 °F
•Relative Humidity : 20 % to 80 % relative humidity (without condensation).
Dynamic Weighing Module
•Dimensions (Width x Length x Height): 25.27" x 19.09" x 11.02"
•Weight : 37.47 lb
•Power supply : 120 V (+/- 10 %) 3 prong
•Frequency : 60 Hz
•Maximum Input Power : 71 W
•Ambient Temperature : + 50 °F to 104 °F
•Relative Humidity : 20 % to 80 % relative humidity (without condensation).
| Page 349 | | mrt-25-2014 02:59 |

3. System Connections
Base + Feeder
CAN
Power
| Page 350 | mrt-25-2014 02:59 |

Base + Feeder + Dynamic Weighing Module
CAN
Power
| Page 351 | mrt-25-2014 02:59 |

Base + Stacker
Power
| Page 352 | mrt-25-2014 02:59 |

4. System Connectors
Base connectors
On the left-hand side
The ON/OFF switch is located at the rear of the right
hand side of the Mailing System base.
ON/OFF switch
To wall socketPower connector
To Conveyor StackerPower connector
For future useRJ 45
To any USB device*USB ports
USB devices : Keyboard, Remote Label Dispenser, Printer, Modem, LAN adaptor, Bar
Code Reader…
All USB devices have to be plugged with the system powered OFF.
| Page 353 | | mrt-25-2014 02:59 |

On the right-hand side
To any USB devices*USB ports
Not applicableRS232 (COM1/2)
To Feeder or Dynamic Weighing ModuleCAN
To displayDVI Connector
To Feeder or Dynamic Weighing ModulePower connector
USB devices : Keyboard, Printer, Modem, LAN adaptor, Bar Code Reader…
All USB devices have to be plugged with the system powered OFF.
| Page 354 | mrt-25-2014 02:59 |

Feeder connectors
To Base or Dynamic Weighing ModulePower connector
To Feeder or Dynamic Weighing ModuleCAN
For future useRJ45
Dynamic Weighing Module connectors
To BaseCAN
To FeederCAN
To BasePower connector
| Page 355 | mrt-25-2014 02:59 |

To BasePower connector
Conveyor Stacker connectors
To BasePower connector
| Page 356 | mrt-25-2014 02:59 |