Neousys Technology POC-400 Series User manual

POC-400 Series
Quick Installation Guide
• Only qualified service personnel should install and service this
product to avoid injury.
• Observe all ESD procedures during installation to avoid damaging
the equipment.
Unpack the equipment and make sure the following tools are
available and delivered contents are correct before you begin the
installation procedure.
1-1. User-provided tools
1-2. Packing List
• Anti-static wrist wrap
1Preparing tools
2
System Status LED
Warning
01
02
03
04
05
POC-400 series system
Drivers & utilities disc
3-pin pluggable terminal block
DIN-rail mount clip
Screw package
1
1
1
1
1
Item Description Quantity
POC-400 Series Front Panel 3USB3.1 Gen1
52.5G Ethernet Port/ IEEE 802.3at Power over Ethernet 6
USB2.0 Port
4
The two USB3. Gen1 ports are implemented by native xHCI
(eXtensible Host Controller Interface) controller and are backward
compatible with USB 2.0, USB 1.1 and USB 1.0 devices. Legacy USB
support is also provided so you can use USB keyboard/ mouse in
DOS environment xHCI driver is supported natively in Windows 10
1
. .
The system offers three 2.5Gb Ethernet ports using Intel® I225
GbE controller. From right to left, they are ports #1, #2 and #3. Ports
#2 and #3 ( ) also offer Power over Ethernet (PoE) connectivity.
The LEDs on the RJ45 connector indicate connection status and speed.
in blue
There are four LED indicators on the front panel: PWR, HDD, WDT and
IGN. The descriptions of these four LEDs are listed in the following table.
The two USB2.0 ports are implemented via native xHCI (eXtensible Host
Controller Interface) and are backward compatible with USB 1.1 and
USB 1.0 devices. Legacy USB support is also provided so you can use
USB keyboard/ mouse in DOS environment. xHCI driver is supported
natively in Windows 10.
DisplayPort
7
The system has two DisplayPort (DP) outputs which are digital
display interfaces that mainly connect video source and carry audio
to a display device. When connecting a DP, it can deliver up to 4K
UHD (4096 x 2160 @ 60Hz) in resolution. The system is designed
to support passive DP adapter/ cable. You can connect to other
display devices using DP-to-HDMI cable or DP-to-DVI cable.
The system supports dual independent display outputs by
connecting display devices DisplayPort connections. To support
dual display outputs and achieve best DisplayPort output resolution
in Windows, you need to install corresponding graphics drivers
The PoE ports supply both power and data on a standard CAT-5/
CAT-6 Ethernet cable. Acting as a PSE (Power Sourcing Equipment),
compliant with IEEE 802.3at, each port delivers up to 25W to a
Powered Device (PD). PoE automatically detects if the connected
device is PoE PD or not, making it compatible with standard Ethernet
devices as well.

3-pin Terminal Block
8
The system accepts a wide range of DC power input from 8 to 35V
via a 3-pin pluggable terminal block, which is fit for field usage
where DC power is usually provided. The screw clamping
mechanism on the terminal block offers connection reliability
when wiring DC power.
Please make sure the voltage of DC power is correct before you connect
it to the system. Supplying a voltage over 35V will damage the system.
Warning
9POC-400 Series Top Panel 10 Power Button
The power button is a non-latched switch for ATX mode on/ off
operation. Press to turn on the system, PWR LED should light up and
to turn off, you can either issue a shutdown command in the OS, or just
press the power button.
11 Reset Button
The reset button is used to manually reset the system in case of
system halt or malfunction. To avoid unexpected reset, the button is
purposely placed behind the panel. To reset, please use a pin-like
object (eg. tip of a pen) to access the reset button.
12 COM1 Port
COM1 port operating mode (RS-232/ 422/ 485), slew-rate and
termination can be set in the BIOS.
13 COM2/3/4 Port
COM2/ 3/ 4 port can be configured in the BIOS as single RS-422/ 485 port
(COM2) or three 3-wire RS-232 ports (COM2/COM3/COM4).
14 3.5mm Microphone-in/ Speaker-out Jack (Optional)
There is a single 3.5mm audio jack on the top panel. The port is used
for microphone input as well as speaker output. To utilize the audio
function in Windows, you need to install corresponding drivers.