Neousys Technology Nuvo-7162GC Series User manual

Neousys Technology Inc.
Nuvo-7160GC Series
Nuvo-7162GC Series
Nuvo-7164GC Series
Nuvo-7166GC Series
User Manual
Revision 1.2

Table of Contents
Table of Contents
Table of Contents...................................................................................................................2
Legal Information...................................................................................................................5
Contact Information...............................................................................................................6
Declaration of Conformity.....................................................................................................6
Copyright Notice....................................................................................................................7
Safety Precautions.................................................................................................................8
Hot Surface Warning..............................................................................................................8
Battery Warning......................................................................................................................8
Service and Maintenance ......................................................................................................9
ESD Precautions....................................................................................................................9
Restricted Access Location ..................................................................................................9
About This Manual...............................................................................................................10
1Introduction
1.1 Product Specifications.............................................................................................13
1.1.1 Nuvo-7160GC Specifications............................................................................13
1.1.2 Nuvo-7162GC Specifications............................................................................15
1.1.3Nuvo-7164GC Specifications............................................................................17
1.1.4 Nuvo-7166GC Specifications............................................................................19
1.2 Nuvo-7160GC Dimensions.......................................................................................21
1.2.1 Nuvo-7160GC Front Panel View.......................................................................21
1.2.2 Nuvo-7160GC Rear Panel View .......................................................................21
1.2.3 Nuvo-7160GC Top View....................................................................................22
1.2.4 Nuvo-7160GC Bottom View..............................................................................23
1.3 Nuvo-7162GC Dimensions.......................................................................................24
1.3.1 Nuvo-7162GC Front Panel View.......................................................................24
1.3.2 Nuvo-7162GC Rear Panel................................................................................24
1.3.3 Nuvo-7162GC Top View....................................................................................25
1.3.4 Nuvo-7162GC Bottom View..............................................................................26
1.4 Nuvo-7164GC Dimensions.......................................................................................27
1.4.1 Nuvo-7164GC Front Panel View.......................................................................27
1.4.2 Nuvo-7164GC Rear Panel View .......................................................................27
1.4.3 Nuvo-7164GC Top View....................................................................................28
1.4.4 Nuvo-7164GC Bottom View..............................................................................29
1.5 Nuvo-7166GC Dimensions.......................................................................................30
1.5.1 Nuvo-7166GC Front Panel View.......................................................................30
1.5.2 Nuvo-7166Gc Rear Panel View........................................................................30
1.5.3 Nuvo-7166GC Top View....................................................................................31
1.5.4 Nuvo-7166GC Bottom View..............................................................................32
2System Overview
2.1 Nuvo-7160GC Packing List......................................................................................33
2.2 Nuvo-7162GC Packing List......................................................................................33
2.3 Nuvo-7164GC Packing List......................................................................................34
2.4 Nuvo-7166GC Packing List......................................................................................34
2.5 Front Panel I/O..........................................................................................................35
2.5.1 USB3.1 Gen 2 Port...........................................................................................36
2.5.2 USB3.1 Gen 1 Port...........................................................................................36
2.5.3 DVI Port ............................................................................................................37
2.5.4 VGA Port...........................................................................................................38
2.5.5 DisplayPort .......................................................................................................39
2.5.6 Micro-SIM (3FF) 1 & 2 Slots .............................................................................40
2.5.7 Ethernet Port/ PoE+..........................................................................................41
2.5.8 Reset Button.....................................................................................................42
2.5.9 LED Indicators ..................................................................................................42
2.5.10 Power Button ....................................................................................................43
2.5.11 Cassette Module...............................................................................................44

Table of Contents
3
2.6 Rear Panel I/O...........................................................................................................45
2.6.1 4-Pole 3.5mm Headphone/ Microphone Jack...................................................46
2.6.2 COM Ports........................................................................................................47
2.6.3 3-Pin Terminal Block for DC and Ignition Input..................................................48
2.6.4 3-Pin Remote On/ Off .......................................................................................48
2.7 Internal I/O Functions...............................................................................................49
2.7.1 Clear CMOS Button..........................................................................................49
2.7.2 Dual SODIMM DRAM Slot................................................................................50
2.7.3 Dual Mode mSATA/ mini-PCIe Socket & Pin Definition.....................................51
2.7.4 M.2 2242 (B Key), Mini-SIM Card Slot & Pin Definition.....................................53
2.7.5 SATA Ports........................................................................................................55
2.7.6 DIP Switch ........................................................................................................56
2.7.7 On/ Off Ctrl & Status Output..............................................................................57
2.7.8 Internal USB 2.0 Port........................................................................................58
2.7.9 M.2 2280 (M Key) Slot for NVMe SSD or OptaneTM Memory............................59
2.7.10 MezIOTM Interface & Pin Definition ...................................................................61
3System Installation
3.1 Disassembling the System......................................................................................64
3.2 Installing Internal Components...............................................................................68
3.2.1 CPU Installation Procedure...............................................................................68
3.2.2DDR4 SO-DIMM Installation.............................................................................74
3.2.3 mPCIe Module, Mini-SIM (2FF) Card and Antenna Installation ........................76
3.2.4 M.2 2242 (B Key) Module and Micro-SIM (3FF) Card Installation.....................78
3.2.5 M.2 2280 NVMe SSD or Intel®OptaneTM Memory Installation..........................80
3.2.6 MezIOTM Module Installation (Optional) ............................................................82
3.2.7 HDD/ SSD Installation.......................................................................................85
3.2.8 Ethernet/ PoE+ Port Panel Screw Fix...............................................................88
3.3 Nuvo-7160GC Graphics Card Installation ..............................................................89
3.4 Nuvo-7162GC Quadro P2200 Installation...............................................................94
3.5 Nuvo-7164GC/ Nuvo-7166GC Tesla Inference Accelerator Installation .............100
3.6 Installing the System Enclosure ...........................................................................109
3.7 Wall Mount and Anti-vibration Damping Bracket Installation.............................112
3.7.1 Wall Mount Bracket Installation.......................................................................112
3.7.2 Anti-vibration Damping Bracket Installation (Optional)....................................114
3.8 Powering On the System .......................................................................................115
3.8.1 Powering On Using the Power Button.............................................................115
3.8.2 Powering On Using External Non-latched Switch...........................................116
3.8.3 Powering On Using Wake-on-LAN..................................................................117
4System Configuration
4.1 BIOS Settings .........................................................................................................119
4.1.1 COM Port Configuration..................................................................................120
4.1.2 COM Port High Speed Mode ..........................................................................121
4.1.3 Delay for PEG Initialization .............................................................................122
4.1.4 SATA Configuration.........................................................................................123
4.1.5 Fan Control Configuration...............................................................................125
4.1.6 TPM Availability...............................................................................................130
4.1.7 Auto Wake on S5............................................................................................131
4.1.8 Power On After Power Failure Option.............................................................132
4.1.9 Power & Performance (CPU SKU Power Configuration)................................133
4.1.10 Wake on LAN Option ......................................................................................134
4.1.11 Boot Menu ......................................................................................................135
4.1.12 Boot Type (Legacy/ UEFI)...............................................................................137
4.1.13 Position New Boot Device...............................................................................138
4.1.14 Watchdog Timer for Booting............................................................................139
4.1.15 Legacy/ UEFI Boot Device..............................................................................140
4.2 AMT Configuration.................................................................................................141
4.3 RAID Configuration................................................................................................142
4.3.1 Legacy Mode RAID Configuration...................................................................142
4.3.2 UEFI Mode RAID Configuration......................................................................148

Table of Contents
4
5OS Support and Driver Installation
5.1 Operating System Compatibility...........................................................................158
5.2 Driver Installation...................................................................................................159
5.2.1 Install Drivers Automatically............................................................................159
5.2.2 Install Drivers Manually...................................................................................160
5.3 Driver Installation for Watchdog Timer Control...................................................161
5.4 Intel®OptaneTM Memory BIOS Setup and Driver Installation..............................162
Appendix A Using WDT & DIO
WDT and DIO Library Installation.....................................................................................172
WDT Functions...................................................................................................................174
InitWDT................................................................................................................................174
SetWDT ...............................................................................................................................174
StartWDT .............................................................................................................................175
ResetWDT............................................................................................................................175
StopWDT .............................................................................................................................175
Appendix B PoE On/ Off Control
GetStatusPoEPort..............................................................................................................176
EnablePoEPort...................................................................................................................177
DisablePoEPort..................................................................................................................178

Legal Information
Legal Information
All Neousys Technology Inc. products shall be subject to the latest Standard
Warranty Policy
Neousys Technology Inc. may modify, update or upgrade the software, firmware or
any accompanying user documentation without any prior notice. Neousys
Technology Inc. will provide access to these new software, firmware or
documentation releases from download sections of our website or through our
service partners.
Before installing any software, applications or components provided by a third party,
customer should ensure that they are compatible and interoperable with Neousys
Technology Inc. product by checking in advance with Neousys Technology Inc.
Customer is solely responsible for ensuring the compatibility and interoperability of
the third party’s products. Customer is further solely responsible for ensuring its
systems, software, and data are adequately backed up as a precaution against
possible failures, alternation, or loss.
For questions in regards to hardware/ software compatibility, customers should
contact Neousys Technology Inc. sales representative or technical support.
To the extent permitted by applicable laws, Neousys Technology Inc. shall NOT be
responsible for any interoperability or compatibility issues that may arise when (1)
products, software, or options not certified and supported; (2) configurations not
certified and supported are used; (3) parts intended for one system is installed in
another system of different make or model.

Contact Information/ Declaration of Conformity
Contact Information
Headquarters
(Taipei, Taiwan)
Neousys Technology Inc.
15F, No.868-3, Zhongzheng Rd., Zhonghe Dist., New Taipei City, 23586, Taiwan
Tel: [phone] Fax: [phone] Email, Website
Americas
(Illinois, USA)
Neousys Technology America Inc.
3384 Commercial Avenue, Northbrook, IL 60062, USA
Tel: [phone]Email, Website
China Neousys Technology (China) Ltd.
Room 612, Building 32, Guiping Road 680, Shanghai
Tel: [phone]Email, Website
Declaration of Conformity
FCC This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at own expense.
CE The product(s) described in this manual complies with all applicable European
Union (CE) directives if it has a CE marking. For computer systems to remain
CE compliant, only CE-compliant parts may be used. Maintaining CE
compliance also requires proper cable and cabling techniques.

Copyright Notice
Copyright Notice
All rights reserved. This publication may not be reproduced, transmitted,
transcribed, stored in a retrieval system, or translated into any language or
computer language, in any form or by any means, electronic, mechanical,
magnetic, optical, chemical, manual or otherwise, without the prior written
consent of Neousys Technology, Inc.
Disclaimer This manual is intended to be used as an informative guide only and is subject
to change without prior notice. It does not represent commitment from Neousys
Technology Inc. Neousys Technology Inc. shall not be liable for any direct,
indirect, special, incidental, or consequential damages arising from the use of
the product or documentation, nor for any infringement on third party rights.
Patents and
Trademarks
Neousys, the Neousys logo, Expansion Cassette, MezIOTM are registered
patents and trademarks of Neousys Technology, Inc.
Windows is a registered trademark of Microsoft Corporation.
Intel®, Core™ are registered trademarks of Intel Corporation
NVIDIA®is a registered trademark of NVIDIA Corporation
All other names, brands, products or services are trademarks or registered
trademarks of their respective owners.

Safety Precautions and Battery Warning
Safety Precautions
Read these instructions carefully before you install, operate, or transport the system.
Install the system or DIN rail associated with, at a sturdy location
Install the power socket outlet near the system where it is easily accessible
Secure each system module(s) using its retaining screws
Place power cords and other connection cables away from foot traffic. Do not place
items over power cords and make sure they do not rest against data cables
Shutdown, disconnect all cables from the system and ground yourself before touching
internal modules
Ensure that the correct power range is being used before powering the device
Should a module fail, arrange for a replacement as soon as possible to minimize
down-time
If the system is not going to be used for a long time, disconnect it from mains (power
socket) to avoid transient over-voltage
By means of a power cord connected to a socket-outlet with earthing connection
This product is intended to be supplied by a Listed PowerAdapter or DC power source,
rated 24Vdc, 16A, Tma 60 degree C and 5000m altitude during operation. If further
assistance is required, please contact Neousys Technology
Hot Surface Warning
HOT SURFACE. DO NOT
TOUCH. “ATTENTION: Surface chaude. Ne
pas toucher.”
WARNING!
Components/ parts inside the
equipment may be hot to touch! Please
wait one-half hour after switching off
before handling parts.
Battery Warning
Batteries are at risk of exploding if incorrectly installed
Do not attempt to recharge, force open, or heat the
battery
Replace the battery only with the same or equivalent
type recommended by the manufacturer

Service and Maintenance/ ESD Precautions/ Restricted Access Location
9
Service and Maintenance
ONLY qualified personnel should service the system
Shutdown the system, disconnect the power cord and all other connections before
servicing the system
When replacing/ installing additional components (expansion card, memory
module, etc.), insert them as gently as possible while assuring proper connector
engagement
ESD Precautions
Handle add-on module, motherboard by their retention screws or the module’s
frame/ heat sink.Avoid touching the PCB circuit board or add-on module
connector pins
Use a grounded wrist strap and an anti-static work pad to discharge static
electricity when installing or maintaining the system
Avoid dust, debris, carpets, plastic, vinyl and 9tyrofoam in your work area.
Do not remove any module or component from its anti-static bag before installation
Restricted Access Location
The controller is intended for installation only in certain environments where both of the
following conditions apply:
Access can only be gained by QUALIFIED SERVICE PERSONNEL who have been
instructed on the reasons for restrictions applied to the location and any precautions
that shall be taken
Access is through the use of a TOOL, lock and key, or other means of security, and
is controlled by the authority responsible for the location

About This Manual
About This Manual
This manual introduces the following Neousys Nuvo systems:
Nuvo-7160GC features Intel®9th/ 8th Gen Core™ octa/ hexa core 35W/ 65W
LGA1151 processors. The Nuvo-7160GC system supports an NVIDIA®graphics
card up to 120W.
Nuvo-7162GC is specifically designed to support an NVIDIA® Quadro P2200 that
offers a longer product life cycle for industrial AI inference applications.
Nuvo-7164GC is specifically designed to support an NVIDIA® Tesla®P4/ T4 for
advanced inference capabilities.
Nuvo-7166GC offers two PCIe slots for users to install a Tesla inference accelerator
and an additional function-purpose high performance PCIe card.
The guide also demonstrates the system’s installation procedures.
Revision History
Version Date Description
1.0 Jul. 2019 Initial release
1.1 Apr. 2020 Added Nuvo-7166GC
1.2 Jun. 2021 Added Nuvo-7162GC

Nuvo-7160/ 7162/ 7164/ 7166GC Series
11
1 Introduction
The Neousys Nuvo-716xGC family are specifically design to house and support NVIDIA®graphics
cards and the more powerful inference-specialized Tesla®P4/ T4 With unique designs in each
system, they serve to fulfill industrial edgeAI and complex inference applications.
Nuvo-7160GC is a ruggedized GPU-aided AI inference
platform designed for modern machine learning applications
such as autonomous driving, facial recognition, vision
inspection and recommendation services. It supports up to a
120W GPU, delivering 4~6 TFLOPS computing power for
inference, as well as Intel®9th/ 8th Gen CoreTM 8-core/ 6-core
CPU, offering over extra 50% CPU performance
enhancement over previous generations.
Nuvo-7160GC
Nuvo-7162C supports NVIDIA®Quadro P2200 graphics card
that offers a longer product life cycle. Featuring a Pascal
GPU that has 1280 CUDAcores and 5GB of GDDR5X
on-board memory and coupled with Neousys patented
thermal design, it can operate up 54°C without the
GPU-throttling. Quadro P2200 is ideal for industrial AI
inference applications
Nuvo-7162GC
Nuvo-7164GC supports NVIDIA®Tesla®P4/ T4 to deliver up
to 40X higher inference capability compared to just CPUs.
Nuvo-7164GC supports Tesla®P4 GPU, featuring 5.5
TFLOPS in FP32 and Tesla®T4 GPU, featuring 8.1 TFLOPS
in FP32 and 130 TOPs in INT8 for real-time inference based
on trained neural network model. Nuvo-7164GC
Nuvo-7166GC is a ruggedizedAI inference platform that
supports an NVIDIATesla T4 inference accelerator plus an
additional PCIe expansion slot for application-oriented
high-performance add-on card. The system is capable of
providing up to 8.1 TFLOPS in FP32 and 130 TOPs in INT8
for real-time inference. The system offers optimal balance
between CPU, GPU and memory performance.
Nuvo-7166GC

Nuvo-7160/ 7162/ 7164/ 7166GC Series
12
Thanks to Neousys’ patented Cassette design and ingenious ventilation mechanism,
Nuvo-7160GC series is capable of effectively dissipating the heat generated by the GPU. By
introducing the guided airflow from intake to exhaust with powerful fans featuring smart fan
control, it allows an NVIDIA®120W GPU to operate at 60°C ambient temperature under 100%
GPU loading.
The Nuvo-7162GC supports for NVIDIA®Quadro P2200 that features a longer product life
cycle than consumer-grade graphics cards. Capable of delivering 3.8 TFLOPS real-time
inference processing power for a variety industrial AI inference applications. The
Nuvo-7164GC/ Nuvo-7166GC systems follow a similar Cassette design but instead guides the
air to flow directly over the heatsink of NVIDIA® Tesla P4/ T4 to sustain 100% GPU loading up
to 50ºC operating temperature.
Nuvo-7160GC series incorporate rich I/O functions such as USB 3.1 Gen2/ Gen1, GbE, COM
and MezIOTM interface in its restricted footprint. It also leverages cutting-edge M.2 NVMe
technology to support over 2000 MB/s disk read/write speed or utilize Intel®OptaneTM memory
to boost the performance of your traditional hard disk drive. Neousys Nuvo-7160GC series are
ideal solutions for emerging edge computing by combining exceptional CPU and GPU
performances.

Nuvo-7160/ 7162/ 7164/ 7166GC Series
13
1.1 Product Specifications
1.1.1 Nuvo-7160GC Specifications
System Core
Processor
Supporting Intel®9th/ 8th Gen Coffee Lake 6 core CPU (LGA1151 socket,
65W/ 35W TDP)
- Intel® Core™i7-8700/ i7-8700T/ i7-9700E/ i7-9700TE
- Intel® Core™i5-8500/ i5-8500T/ i5-9500E/ i5-9500TE
- Intel® Core™ i3-8100/ i3-8100T/ i3-9100E/ i3-9100TE
Chipset Intel®Q370 Platform Controller Hub
Graphics Integrated Intel®UHD Graphics 630
Memory Up to 64GB DDR4 2666/ 2400 SDRAM (two SODIMM slots)
AMT Supports AMT 12.0
TPM Supports TPM 2.0
I/O Interface
Ethernet port 6x Gigabit Ethernet ports (I219 and 5x I210)
PoE+ Optional IEEE 802.3at PoE+ PSE for Port 3 ~ Port 6
100 W total power budget
USB 4x USB 3.1 Gen2 (10 Gbps) ports
4x USB 3.1 Gen1 (5 Gbps) ports
Video Port
1x VGA connector, supporting 1920 x 1200 resolution
1x DVI-D connector, supporting 1920 x 1200 resolution
1x DisplayPort connector, supporting 4096 x 2304 resolution
Serial Port 2x software-programmable RS-232/ 422/ 485 ports (COM1/ COM2)
2x RS-232 ports (COM3/ COM4)
Audio 1x 3.5mm jack for mic-in and speaker-out
Storage Interface
SATA HDD 2x internal SATA port for 2.5” HDD/ SSD (support up to 15mm thickness),
supporting RAID 0/1
M.2 NVMe 1x M.2 2280 M key NVMe socket (PCIe Gen3 x4 and SATA signal) for
NVMe/ SATA SSD or Intel®OptaneTM memory installation
mSATA 1x full-size mSATA port (mux with mini-PCIe)
Internal Expansion Bus
PCI Express
1x PCIe x16 slot@Gen3, 16-lanes PCIe signals in Cassette for
installing NVIDIA®120W GPU (Max. graphics card dimension is 188
mm(L) x 121 mm(W), dual slot allocation)

Nuvo-7160/ 7162/ 7164/ 7166GC Series
14
* For i7-8700/ i7-9700E operating at 65W mode, the highest operating temperature shall be
limited to 50°C and thermal throttling may occur when sustained full-loading applied. Users
can configure CPU power in BIOS to obtain higher operating temperature.
** For sub-zero operating temperature, a wide temperature HDD or Solid State Disk (SSD) is
required.
Mini PCI-E 1x full-size mini PCI Express socket with internal SIM socket (mux with
mSATA)
M.2 1x M.2 2242 B key socket with dual front-accessible SIM sockets,
supporting dual SIM mode with selected M.2 LTE module
Expandable I/O 1x MezIOTM expansion port for Neousys MezIOTM modules
Power Supply
DC Input 1x 3-pin pluggable terminal block for 8~35VDC input
Remote Ctrl. &
Status Output 1x 3-pin pluggable terminal block for remote control and PWR LED output
Maximum
Power
Consumption
With 120W NVIDIA®GPU
With i7-8700 (35W mode): 211W (Max.) @ 24V
With i7-8700 (65W mode): 240W (Max.) @ 24V
Mechanical
Dimension 240mm (W) x 225 mm (D) x111 mm (H)
Weight 4.5 Kg (including CPU, GPU, memory and HDD)
Mounting Wall-mount bracket
Environmental
Operating
Temperature
With 35W CPU and Quadro P2200
-25°C ~ 60°C **
With 65W CPU and Quadro P2200
-25°C ~ 60°C */** (configured as 35W TDP mode)
-25°C ~ 50°C */** (configured as 65W TDP mode)
Storage
Temperature -40°C ~85°C
Humidity 10%~90% , non-condensing
Vibration Operating, MIL-STD-810G, Method 514.6, Category 4
Shock Operating, MIL-STD-810G, Method 516.6, Procedure I, Table 516.6-II
EMC CE/FCC ClassA, according to EN 55032 & EN 55024

Nuvo-7160/ 7162/ 7164/ 7166GC Series
15
1.1.2 Nuvo-7162GC Specifications
System Core
Processor
Supporting Intel®9th/ 8th Gen Coffee Lake 6 core CPU (LGA1151 socket,
65W/ 35W TDP)
- Intel® Core™i7-8700/ i7-8700T/ i7-9700E/ i7-9700TE
- Intel® Core™i5-8500/ i5-8500T/ i5-9500E/ i5-9500TE
- Intel® Core™ i3-8100/ i3-8100T/ i3-9100E/ i3-9100TE
Chipset Intel®Q370 Platform Controller Hub
Graphics Integrated Intel®UHD Graphics 630
Memory Up to 64GB DDR4 2666/ 2400 SDRAM (two SODIMM slots)
AMT Supports AMT 12.0
TPM Supports TPM 2.0
I/O Interface
Ethernet port 6x Gigabit Ethernet ports (I219 and 5x I210)
PoE+ Optional IEEE 802.3at PoE+ PSE for Port 3 ~ Port 6
100 W total power budget
USB 4x USB 3.1 Gen2 (10 Gbps) ports
4x USB 3.1 Gen1 (5 Gbps) ports
Video Port
1x VGA connector, supporting 1920 x 1200 resolution
1x DVI-D connector, supporting 1920 x 1200 resolution
1x DisplayPort connector, supporting 4096 x 2304 resolution
Serial Port 2x software-programmable RS-232/ 422/ 485 ports (COM1/ COM2)
2x RS-232 ports (COM3/ COM4)
Audio 1x 3.5mm jack for mic-in and speaker-out
Storage Interface
SATA HDD 2x internal SATA port for 2.5” HDD/ SSD (support up to 15mm thickness),
supporting RAID 0/1
M.2 NVMe 1x M.2 2280 M key NVMe socket (PCIe Gen3 x4 and SATA signal) for
NVMe/ SATA SSD or Intel®OptaneTM memory installation
mSATA 1x full-size mSATA port (mux with mini-PCIe)
Internal Expansion Bus
PCIe 1x PCIe x16 slot @ Gen3, 16-lanes PCIe signal in Cassette for installing
NVIDIA® Quadro P2200
Mini PCI-E 1x full-size mini PCI Express socket with internal SIM socket (mux with
mSATA)
M.2 1x M.2 2242 B key socket with dual front-accessible SIM sockets,

Nuvo-7160/ 7162/ 7164/ 7166GC Series
16
* For i7-8700/ i7-9700E operating at 65W mode, the highest operating temperature shall be
limited to 50°C and thermal throttling may occur when sustained full-loading applied. Users
can configure CPU power in BIOS to obtain higher operating temperature.
** For sub-zero operating temperature, a wide temperature HDD or Solid State Disk (SSD) is
required.
supporting dual SIM mode with selected M.2 LTE module
Expandable I/O 1x MezIOTM expansion port for Neousys MezIOTM modules
Power Supply
DC Input 1x 3-pin pluggable terminal block for 8~35VDC input
Remote Ctrl. &
Status Output 1x 3-pin pluggable terminal block for remote control and PWR LED output
Mechanical
Dimension 240mm (W) x 225 mm (D) x111 mm (H)
Weight 4.5 Kg (including CPU, GPU, memory and HDD)
Mounting Wall-mount (standard)
Environmental
Operating
Temperature
With 35W CPU and Quadro P2200
-25°C ~ 60°C **
With 65W CPU and Quadro P2200
-25°C ~ 60°C */** (configured as 35W TDP mode)
-25°C ~ 50°C */** (configured as 65W TDP mode)
Storage
Temperature -40°C ~85°C
Humidity 10%~90% , non-condensing
Vibration Operating, MIL-STD-810G, Method 514.6, Category 4
Shock Operating, MIL-STD-810G, Method 516.6, Procedure I, Table 516.6-II
EMC CE/FCC ClassA, according to EN 55032 & EN 55024

Nuvo-7160/ 7162/ 7164/ 7166GC Series
17
1.1.3 Nuvo-7164GC Specifications
System Core
Processor
Supporting Intel®9th/ 8th Gen Coffee Lake 6 core CPU (LGA1151 socket,
65W/ 35W TDP)
- Intel® Core™i7-8700/ i7-8700T/ i7-9700E/ i7-9700TE
- Intel® Core™i5-8500/ i5-8500T/ i5-9500E/ i5-9500TE
- Intel® Core™ i3-8100/ i3-8100T/ i3-9100E/ i3-9100TE
Chipset Intel®Q370 Platform Controller Hub
Graphics Integrated Intel®UHD Graphics 630
Memory Up to 64GB DDR4 2666/ 2400 SDRAM (two SODIMM slots)
AMT Supports AMT 12.0
TPM Supports TPM 2.0
I/O Interface
Ethernet port 6x Gigabit Ethernet ports (I219 and 5x I210)
PoE+ Optional IEEE 802.3at PoE+ PSE for Port 3 ~ Port 6
100 W total power budget
USB 4x USB 3.1 Gen2 (10 Gbps) ports
4x USB 3.1 Gen1 (5 Gbps) ports
Video Port
1x VGA connector, supporting 1920 x 1200 resolution
1x DVI-D connector, supporting 1920 x 1200 resolution
1x DisplayPort connector, supporting 4096 x 2304 resolution
Serial Port 2x software-programmable RS-232/ 422/ 485 ports (COM1/ COM2)
2x RS-232 ports (COM3/ COM4)
Audio 1x 3.5mm jack for mic-in and speaker-out
Storage Interface
SATA HDD 2x internal SATA port for 2.5” HDD/ SSD (support up to 15mm thickness),
supporting RAID 0/1
M.2 NVMe 1x M.2 2280 M key NVMe socket (PCIe Gen3 x4 and SATA signal) for
NVMe/ SATA SSD or Intel®OptaneTM memory installation
mSATA 1x full-size mSATA port (mux with mini-PCIe)
Internal Expansion Bus
PCIe 1x PCIe x16 slot @ Gen3, 16-lanes PCIe signal in Cassette for installing
NVIDIA® Tesla T4 GPU
Mini PCI-E 1x full-size mini PCI Express socket with internal SIM socket (mux with
mSATA)
M.2 1x M.2 2242 B key socket with dual front-accessible SIM sockets,

Nuvo-7160/ 7162/ 7164/ 7166GC Series
18
* For i7-8700/ i7-9700E running at 65W mode, the highest operating temperature shall be
limited to 50°C and thermal throttling may occur when sustained full-loading applied. Users
can configure CPU power in BIOS to obtain higher operating temperature.
** For sub-zero operating temperature, a wide temperature HDD or Solid State Disk (SSD) is
required.
supporting dual SIM mode with selected M.2 LTE module
Expandable I/O 1x MezIOTM expansion port for Neousys MezIOTM modules
Power Supply
DC Input 1x 3-pin pluggable terminal block for 8~35VDC input
Remote Ctrl. &
Status Output 1x 3-pin pluggable terminal block for remote control and PWR LED output
Mechanical
Dimension 240mm (W) x 225 mm (D) x111 mm (H)
Weight 4.5 Kg (including CPU, GPU, memory and HDD)
Mounting Wall-mount (standard) or DIN-Rail mounting (optional)
Environmental
Operating
Temperature
With 35W CPU
-25°C ~ 60°C **
With 65W CPU
-25°C ~ 60°C */** (configured as 35W TDP mode)
-25°C ~ 50°C */** (configured as 65W TDP mode)
In compliance with NVIDIA® Tesla T4 warranty policy, an operating
temperature of 0°C~50°C is required for systems with Tesla T4 installed
Storage
Temperature -40°C ~85°C
Humidity 10%~90% , non-condensing
Vibration Operating, MIL-STD-810G, Method 514.6, Category 4
Shock Operating, MIL-STD-810G, Method 516.6, Procedure I, Table 516.6-II
EMC CE/FCC ClassA, according to EN 55032 & EN 55024

Nuvo-7160/ 7162/ 7164/ 7166GC Series
19
1.1.4 Nuvo-7166GC Specifications
System Core
Processor
Supporting Intel®9th/ 8th Gen Coffee Lake 6 core CPU (LGA1151 socket,
65W/ 35W TDP)
- Intel® Core™i7-8700/ i7-8700T/ i7-9700E/ i7-9700TE
- Intel® Core™i5-8500/ i5-8500T/ i5-9500E/ i5-9500TE
- Intel® Core™ i3-8100/ i3-8100T/ i3-9100E/ i3-9100TE
Chipset Intel®Q370 Platform Controller Hub
Graphics Integrated Intel®UHD Graphics 630
Memory Up to 64GB DDR4 2666/ 2400 SDRAM (two SODIMM slots)
AMT Supports AMT 12.0
TPM Supports TPM 2.0
I/O Interface
Ethernet port 6x Gigabit Ethernet ports (I219 and 5x I210)
PoE+ Optional IEEE 802.3at PoE+ PSE for Port 3 ~ Port 6
100 W total power budget
USB 4x USB 3.1 Gen2 (10 Gbps) ports
4x USB 3.1 Gen1 (5 Gbps) ports
Video Port
1x VGA connector, supporting 1920 x 1200 resolution
1x DVI-D connector, supporting 1920 x 1200 resolution
1x DisplayPort connector, supporting 4096 x 2304 resolution
Serial Port 2x software-programmable RS-232/ 422/ 485 ports (COM1/ COM2)
2x RS-232 ports (COM3/ COM4)
Audio 1x 3.5mm jack for mic-in and speaker-out
Storage Interface
SATA HDD 2x internal SATA port for 2.5” HDD/ SSD (support up to 15mm thickness),
supporting RAID 0/1
M.2 NVMe 1x M.2 2280 M key NVMe socket (PCIe Gen3 x4 and SATAsignal) for
NVMe/ SATA SSD or Intel®OptaneTM memory installation
mSATA 1x full-size mSATA port (mux with mini-PCIe)
Internal Expansion Bus
PCI Express 2x PCIe x16 slot @ Gen3, 8-lanes PCIe signal in Cassette for installing
NVIDIA® Tesla T4 GPU and one additional PCIe card
Mini PCI-E 1x full-size mini PCI Express socket with internal SIM socket (mux with
mSATA)
M.2 1x M.2 2242 B key socket with dual front-accessible SIM sockets,

Nuvo-7160/ 7162/ 7164/ 7166GC Series
20
* For i7-8700/ i7-9700E running at 65W mode, the highest operating temperature shall be
limited to 50°C and thermal throttling may occur when sustained full-loading applied. Users
can configure CPU power in BIOS to obtain higher operating temperature.
** For sub-zero operating temperature, a wide temperature HDD or Solid State Disk (SSD) is
required.
supporting dual SIM mode with selected M.2 LTE module
Expandable I/O 1x MezIOTM expansion port for Neousys MezIOTM modules
Power Supply
DC Input 1x 3-pin pluggable terminal block for 8~35VDC input
Remote Ctrl. &
Status Output 1x 3-pin pluggable terminal block for remote control and PWR LED output
Mechanical
Dimension 240mm (W) x 225 mm (D) x111 mm (H)
Weight 4.5 Kg (including CPU, GPU, memory and HDD)
Mounting Wall-mount (standard) or DIN-Rail mounting (optional)
Environmental
Operating
Temperature
With 35W CPU
-25°C ~ 60°C **
With 65W CPU
-25°C ~ 60°C */** (configured as 35W TDP mode)
-25°C ~ 50°C */** (configured as 65W TDP mode)
In compliance with NVIDIA® Tesla T4 warranty policy, an operating
temperature of 0°C~50°C is required for systems with Tesla T4 installed
Storage
Temperature -40°C ~85°C
Humidity 10%~90% , non-condensing
Vibration Operating, MIL-STD-810G, Method 514.6, Category 4
Shock Operating, MIL-STD-810G, Method 516.6, Procedure I, Table 516.6-II
EMC CE/FCC Class A, according to EN 55032 & EN 55024