Neousys Technology Nuvo-9501 Reference manual

Nuvo-9501
Quick Introduction Guide
• Only qualified service personnel should install and service this
product to avoid damage or injury.
• Observe all ESD procedures during installation to avoid damaging
the equipment.
Unpack the equipment and make sure the following tools are
available and delivered contents are correct.
1-1. User-provided tools
1-2. Packing List
• Anti-static wrist wrap
1Preparing tools
2
Warning
Overview - Front Panel
01
02
03
04
Nuvo-9501 system
CPU bracket
3-pin pluggable terminal block
Screw pack
1
1
1
1
Item Description Quantity
Power Button
3
The power button is a non-latched switch for ATX mode on/off
operation. To turn on the system, press the power button and the
PWR LED should light-up green. To turn off the system, issuing a
shutdown command in OS is preferred, or you can simply press the
power button. To force shutdown when the system freezes, press
and hold the power button for 5 seconds. Please note that there is a
5-second interval between on/off operations (i.e. once the system is
turned off, there is a 5-second wait before you can power-on the
system).
System Status LED
4
There are four LED indicators on the I/O panel: PWR (power),
WDT (Watchdog timer), HDD (hard disk drive). The descriptions
of the LED are listed in the following table.
Reset Button
5
The reset button is used to manually reset the system in case of
system halt or malfunction. To avoid unexpected reset, the button is
purposely placed behind the panel. To reset, please use a pin-like
object (eg. tip of a pen) to access the reset button.
2.5G Ethernet Port
6
The system offers two 2.5Gb Ethernet ports using Intel® I226
controller, and each port each come with screw-lock mechanism
(indicated in ). When plugged in and connected via the Ethernet
cable, the LEDs on the RJ45 connector indicate connection status
and speed.
red

CMOS Reset Button
9
DisplayPort 8
7USB3.2 Gen1 Port
The system has a DisplayPort (DP) output which is a digital display
interfaces that mainly connect video source and carry audio to a
display device. When connecting a DP, it can deliver up to 4K UHD
(4096 x 2304) in resolution. The system is designed to support
passive DP adapter/ cable. You can connect to other display
devices using DP-to-HDMI cable or DP-to-DVI cable.
With the VGA output on the rear panel, the system supports dual
independent display outputs. To support dual display outputs and
achieve best VGA/ DisplayPort output resolution in Windows, you
need to install corresponding graphics drivers.
The system offers four USB 3.2 Gen1 (SuperSpeed USB) ports on its
front panel with screw-lock mechanism. They are backward
compatible with USB 2.0, USB 1.1 and USB 1.0 devices. UEFI USB is
also supported so you can use USB keyboard/ mouse in UEFI shell
environment. USB 3.2 Gen1 driver is supported natively in Windows
10. The screw-lock mechanism is available on the three ports
indicated in and and due to the width of the
connector, only t
.
blue red
red
, screw-lock
he USB ports indicated in can be connected
simultaneously when using the screw-lock mechanism
The CMOS Reset button is used to manually reset the motherboard
BIOS in case of system halt or malfunction. To avoid unexpected
operation, it is purposely placed behind the panel. To reset, please use
the tip of a pen, press and hold for at least 5 seconds to reset the BIOS.
Depending on the design of your screw-lock USB connector, the CMOS
reset button may be obstructed if the USB pot below is connected.
10 Overview - Rear Panel
Note
4-Pole 3.5mm Microphone-in/ Speaker-out Jack
11 VGA Port
Note
Please make sure your VGA cable includes SDA and SCL (DDC clock and
data) signals for correct communication with monitor to get
resolution/timing information. A cable without SDA/ SCL can cause blank
screen on your VGA monitor due to incorrect resolution/timing output.
12
VGA connector is the most common video display connection. The
VGA output supports up to 1920x1200@60Hz resolution.
With the DisplayPort on the front panel, the system supports dual
independent display outputs. To support dual display outputs and
achieve best VGA/ DisplayPort output resolution in Windows, you
need to install corresponding graphics drivers.
There is a female 4-pole audio jack for headphone (speaker)
output and microphone input. To utilize the audio function in
Windows, you need to install corresponding drivers.

COM2/3/4 Port
14
The port s it
3
provide up to 921600 bps baud rate, can be configured in
the BIOS as single RS-422/ 485 port (COM2) or three 3-wire RS-232
ports (COM2/ / 4). An optional 1-to-3 Y-cable is available to
connect three RS-232 devices.
15 USB2.0 Port
The USB2.0 ports are implemented via native xHCI (eXtensible
Host Controller Interface) in the Intel 600 chipset and are
backward compatible with USB 1.1 and USB 1.0 devices. UEFI
USB support is also provided so you can use USB keyboard/
mouse in UEFI shell environment.
xHCI driver is supported natively in Windows 10, therefore you do
not need to install xHCI driver to utilize USB functions.
3-pin Terminal Block & Remote ON/ Off
12
The system accepts a wide range of DC power input from 8 to 35V
via a 3-pin pluggable terminal block, which is fit for field usage
where DC power is usually provided. The screw clamping
mechanism on the terminal block offers connection reliability when
wiring DC power.
The Remote On/ Off connection allows for external switch
extension. It is useful when the system is placed in a cabinet or a
not easily accessed location.
Please make sure the voltage of DC power is correct before you
connect it to the system. Supplying a voltage over 35V will
damage the system.
Warning
13 COM1 Port
The port s itprovide up to 921600 bps baud rate, is
a software-configurable RS-232/422/485 port via
9-pin D-Sub male connector. The operation mode,
slew rate and termination of COM1 can be set in
BIOS setup utility. The following table describes
the pin definition of COM ports.