New Holland T7 AutoCommand Mounting instructions

T7 AutoCommand™
Quick Instruction Guide
1

Contents
Getting Started……………………………………………………………….1
The CommandGrip™……………………………………………………...2
Intuitive Control Panel…………………………………………………...3
Additional SideWinder™ II Controls ……………………………….4
PTO Operation………………………………………………………………..5
‘C’ Pillar Controls…………………………………………………………….6
Hydraulic Remote Valves…………………………………………….....7
Remote Valve Management…………………………………………...8
Headland Turn Sequence (HTS)
Management ………………………………………………………………...9
Headland Turn Sequence (HTS)
Programming ……………………………………………………………….10

1
Getting Started
•Stage 1: Ensure the shuttle lever is in the park
position. Press lever down then forward.
•Stage 2: Depress clutch pedal. In order to start the
engine the clutch pedal must be depressed.
•Stage 3: Choose the required speed range.
3 speed ranges (target speeds) each in forward and reverse are
available. The target speed can be adjusted on the scroll wheel
from 0.03 and 43 or 53kph.
•Stage 4: Start driving! Select driving direction, with
shuttle lever. Ground speed can be changed using the command
grip or foot pedal depending on the selected mode.
•Stage 5: Acceleration. Your T7 will increase the ground
speed proportionally to the rate you move the CommandGrip™
or driving pedal. Quick movement = quick acceleration.
•Stage 6: Deceleration. Driving with the foot pedal: rate
of speed reduction depends on aggressively level set with
button on ICP. Level 1 is default and always available at key on.

The Command Grip
1
3 2
5
6 7 8
4
Electro-hydraulic remote (EHR) control
Rear hitch
IntelliSteer™ activation/cancel
Headland Turn Sequence (HTS)
2
3
4
1
Power shuttle (forward and reverse)
Target speed adjustment
Target speed selection
Cruise control
5
6
7
8
New Anti-Jack Knife
Increased safety on steep terrain as this feature brakes the implement while the
tractor continues at a fixed speed.
•Depress forward/reverse button depending on direction of travel
•The activation of the Anti-Jack Knife function is now
shown on IntelliView™ IV screen
•The transmission ratio will now always be
immediately frozen as long as the forward/reverse
button is depressed
•Press the brake pedal (the tractor moves on while
the implement brakes are activated)
2
The CommandGrip™
5
6
8
7

GENESIS® T8 Series SmartTrax™
Components
ICP Intuitive Control Panel
Constant engine speed: press button 1 or 2 actual engine
speed is saved constant speed function is activated. Fine
adjustment with arrow keys
Headland Turning Sequence:
•Recording
•Automatic or sequential
control
Hydraulic top link and lift rod
controls (if fitted)
Front and rear arms
raise/lower fine adjust
Auto PTO
Slip control activation
Traction management: automatic or
permanent engagement of 4wd and diff-lock
Front axle suspension. Locks
suspension below 12km/h,
keep button pressed for 3 sec
toggle between suspension
stiffness hard/medium/soft
Joystick control selects which
remotes are operated by the
joystick
Deceleration function
Manual mode M: Turns of the
ground speed management
(GSM)
3

Additional SideWinder™ II Controls
4
6
5
1
2
3
Controls under the lid:
Drop rate rear hitch
Sensitivity draft control system
Height limitation rear hitch
Slip control value [%]
Remote valve configuration –oil flow,
timer. Push-turn logic
Lift height limitation front hitch
1
2
3
4
5
6
Engine droop dial: Adjusts maximum RPM of the
engine depending on driver/implement
requirements (positioned as shown on T7HD and
behind PTO buttons on T7)
Emergency brake: spring loaded lever the
further you press the increase the pressure
on the brakes (T7 HD only) 4

PTO Operation
Brake release front / rear
PTO Speed Selection
PTO Fender on/off
PTO engage front / rear
2 Speed front PTO
Engine speeds:
•1000 @ 1886 rpm
•1000E @ 1585 rpm (T7 HD only)
4 speed Rear PTO
Engine Speeds:
•540 @ 1930 rpm
•540E @ 1583 rpm
•1000 @ 1886 rpm
•1000E @ 1585 rpm
Auto PTO
For Front and Rear PTO
1. Set lifting height values for rear and front hitch,
at which PTO shall switch off and on within the
IntelliView™ IV monitor. (through work
condition, settings)
2. Activate AUTO PTO switch on ICP while PTO is
on
5

‘C’ Pillar Controls
1 2
3
4 5
6
7
Hydraulic main switch
Up: Remote valves active
Centre: Remotes, rear hitch locked
Down: Remotes + rear hitch active
High mounted road lights / LED stripes in bonnet
IntelliSteer™ activation / lock
ISO BUS class 3 activation / engagement
Electronic battery isolator
Diagnostic plug
9 pin ISO BUS connector
1
2
3
4
5
6
7
6

GENESIS® T8 Series SmartTrax™
Belt Widths
Hydraulic Remote Valves
F –Float
L –Lower
N –Neutral
R –Raise
4 Paddle levers to control up to 4 remote valves
Control of rear and mid mounted
remotes can be switched between
joystick and paddle levers (using
button shown on ICP)
View of the hydraulic remote slices from
rear of the tractor
7

Remote Valve Management
Personalise which remotes are operated from either the paddle levers on the
armrest, the remote joystick or the remote buttons on the CommandGrip™
This can be done through the IntelliView™ IV screen as shown.
You can save custom settings against specific implement names depending on
what implement is being used. 8