No Butts Bin SR7896 User manual

Assembly Instructions
Product code: SR7896
Doc. No.: SR7896-01-191021-USA

12
5X
11
2X
10
2X
9
5X
8
16X
13
4X
15
4X
1
8X
6
4
1X
3
9X
13
4X
8
16X
1
8X
10
2X
2
8X
6
2X
3
9X
5
EXPLODED VIEW AND TOOLS
2
Tools required:
Drill/Screwdriver
Mallet
Wrench
Torx bit
ITEM
NO.
PART
NO.
DESCRIPTION
DIMENSION IMAGE
QTY.
1
S1
Full Frame
2000 x 1035
8
2
CB1
Corner Bracket - CB1
110 x 110 x
40 8
3
JF1
Joint Flat - JF1
110 x 40
9
4
ST3
Roof Tie - ST3
40 x 40 x
2060 1
5
EC40
40x40 PLASTIC END
CAP
STD. STOCK
ITEM
2
6
FT1
FT1 BRACKET
40X40X100
2
7
FT3
FT3 Bracket
40 x 80 x 106
7
8
DR
Rafter Bracket
110 x 40 x 52
16
9
DR1R
Rafter
1142.5 5
10
DR1I
Infill Panel
1134 x 200
2
11
DR1PO
Roof Panel Outer
1211 x 1055
2
12
DR1T
Roof Trim
1211 x 80
5
13
DRATO
DR Ally-Angle Trim
Outer
50 x 50 x
1055 4
14
DR1PI
DR1 Roof Panel Inner
1210 x 1035
2
15
DRATI
DR Ally-Angle Trim
Inner
50 x 50 x
1035 4

3
PARTS LIST AND FITTINGS
Fittings Bolt set M10 T25 T38 AB1210
M10 x 60mm Nut Washer
Black
Cap
25 mm
Tech
screw
38 mm
Tech
screw
M10/12 x 100
mm Concrete
Bolt
Pack A+B 40 40 80 80 136 66 13
Required 19 19 38 38 100 30 9
Image
ITEM
NO.
PART
NO.
DESCRIPTION
Size (inch) IMAGE
QTY.
1
S1
Full Frame
78.74 x 40.74
8
2
CB1
Corner Bracket -
CB1
4.3 x 4.3 x 1.57
8
3
JF1
Joint Flat - JF1
4.33 x 1.57
9
4
ST3
Roof Tie - ST3
81.1 1
5
EC40
40x40 PLASTIC
END CAP
1.57 x 1.57
2
6
FT1
FT1 BRACKET
1.57 x 1.57 x 3.94
2
7
FT3
FT3 Bracket
1.57 x 3.15 x 4.17
7
8
DR
Rafter Bracket
4.3 x 1.6 x 2
16
9
DR1R
Rafter
45 5
10
DR1I
Infill Panel
44.6 x 7.9
2
11
DR1PO
Roof Panel Outer
47.7 x 41.5
2
12
DR1T
Roof Trim
47.7 x 3.1
5
13
DRATO
DR Ally-Angle Trim
Outer
2 x 2 x 41.5
4
14
DR1PI
DR1 Roof Panel
Inner
47.6 x 40.75
2
15
DRATI
DR Ally-Angle Trim
Inner
2 x 2 x 40.75
4

42.32
164.57
42.32
A
Check overall dimensions
to ensure correct alignment
CB1
JF1
S1 FRAME
ST3
NOTE: Insert EC40 into
ST3 before installation.
DETAIL A
SCALE 1 : 7
CB1 UNDERNEATH
JF1 ON INNER
ST3 TIE BAR
CB1CB1CB1CB1
Ensure correct
alignement on all corners
Step 1
Assemble S1 frames to make up the main structure using CB1 brackets
for the corners and JF1 brackets for straight joints. Also use CB1 and JF1
brackets to secure the ST3 tie bar.
4

1035 1035
C
39.17
40.75 40.75 40.75 40.75
SCALE 1 : 30
DR
DR
DR
DR1I
DR1I
DR1R
DR1R
DR1R
Step 2
Attach the DR1R rafters using the DR brackets and 1 inch tech screws.
The Infill panels (DR1I) are also attached using 1 inch tech screws but must be
placed into positioned at the same time as the end rafters.
5

DRATO
DRATODRATO
DRATO
DRATIDRATIDRATIDRATI
DR1PO
DR1PO
DR1PI
DR1PI
DR1T
DR1T
DR1T
DR1T
DRATO
DRATO
DRATO
DRATO
DRATI
DRATI
DRATI
DRATI
DR1T
Step 3
Arrange the roof panels by lining up the end panels( DR1PO ) flush with the outer
rafters and equally space the middle pieces( DR1PI ) between the outers. Seal
the gaps between the panels and the outer edges with the DR1T strips. Then
cap the bottom of the rafters using the DRATO and DRATI angles.
6

FT3
FT3
FT1
FT1
Step 4
Move the shelter into its final position and attach the floor brackets.
FT1 brackets are used where there is only a single leg and FT3
brackets used where there are two legs next to each other.
7

164.57
167.36 TO FOOT HOLE CENTERS
41.12 40.75 85.49
44.71
39.17
41.12 40.75 40.75 40.75
41.12
8
GROUND ANCHOR POSITIONS AND OVERALL SIZE
SUGESTED SIZE FOR BASE: 8Inch OVERSIZES ON ALL 4 SIDES
Scale 1:20

9
MAINTENANCE:
To ensure your products give you many years of use we recommend that you:
THANK YOU
FOR PURCHASING THIS PRODUCT
Clean panels regularly with soapy water •
Ensure all fitting are tight (for example after a big storm) •
Touch up any exposed metal should it get scratched •
CONTACT DETAILS:
No Butts Bin Company, Inc.
16 Birch Lane, Madison, CT 06443
Email: [email protected]
Web: www.nobutts.com
Tel: [phone]
All Parts and Fixing checked by:
Print Name: Signature