Ogawa OG8020 User manual

OG8020
Assembly Instructions
Failure to follow instruction manual
can void warranty

OG8020 Instruction Manual
STEP 2: Open box 1 and remove all the packing materials. Then take the base out of the box
and get rid of the plastic bag which covers the base. As pictured below.
Box 2: Backrest
Box 1:The Base
Box 3: Side Boards
STEP 1: OG8020 massage chair arrives in three boxes. The base is packed in box 1, the back-
rest is packed in box 2, and the side boards packed in box 3. As pictured below.
STEP 3: Take the tablet holder from the footrest, remove the packing material and set aside. The
accessory box include the power cord, instruction manual, warranty card, tablet cover,
and arm hardware. As pictured below.

STEP 4:
STEP 5:
Cut the cable tie, used for shipping, securing the backrest actuator. Remove the
protective material which wrapped on the head of backrest actuator. Remove the cotter
pin and bolt and set aside. As pictured below.
Remove the protective material. Remove the cotter pin and bolt and set aside.
STEP 6: Preferably using two people, carefully set the backrest on the cradle points on the
base. With the backrest in a vertical position, ensure it properly engages to the base.
Caution: DO NOT rest the backrest onto floor while it is vertically otherwise
damage to the backrest bracket maybe occur.
Remove the cardboard.
Set the backrest on the cradle points on the base. the backrest properly engages to the base
Remove the two screw.
Open box 2 and remove packing materials. Take the backrest out of the box and set it
on the floor. DO NOT pull on the air hose. DO NOT pull on the backrest cable. DO
NOT pull on the pillow or damage could occur. As pictured below. STEP 7: Push the backrest forward and let it lean on the seat pad.
Use the bolt and cotter pin to attach the backrest and backrest actuator.
Attach backrest bracket to reclining actuator. Lock the bolt by cotter pin.
Aline the two brackets.

STEP 9: Locate connector on PCB tray.Securely attach the backrest harness to PCB tray and
lock it by screws on the connector.
STEP 10: Recline the backrest until it locks into position.
The air hose must upward.Locate the connecter on the inflator pump box.
STEP 8: Push the backrest forward and let it lean on the seat pad. Use the bolt and cotter pin to
attach the backrest and backrest actuator. Connect the backrest 4-way air hose
connecter to the air pump box.
STEP 11: Open box 3 and remove the two side boards. Locate the two zipper heads at bottom
edge of the side board. Unzip these two zipper heads to both ends. On the side board,
there are two metal plates. Locate the hole under each metal plate. As pictured below.
Unzip these two zipper heads to both ends.
Locate the hole under each metal plate.
connect the connector to PCB tray.
Make sure lock it by the screws.
Locate connector.

STEP 13:
STEP 12: Connect the air hose and then the wire harness to their appropriate connectors.
Carefully attach the side board onto the base. Align and insert the two metal bars on
the base into the holes under the metal plate. As pictured below.
Use two screws to attach the side board and close the zipper. As pictured below.
STEP 14: Remove the protective cloth strips on the backrest pad and attach the backrest pad
onto backrest. Attach the zipper to the backrest pad. Then attach the pillow. As
pictured below.
Connect the air hose and
wire connecters.

.
STEP 16: Connect the chair to power supply, turn on the power switch. Then you can enjoy your
massage chair. .
Locate the power switch

STEP 15: Attach the tablet holder onto right side armrest. Then attach the tablet cover onto the
holder. As pictured below.