Oneida Air Systems 2 HP Commercial Cyclonic Dust Collector User manual

2 HP
Commercial Cyclonic
Dust Collector
Oneida Air Systems, Inc. 1001 West Fayette St., Syracuse, N.Y. 13204
Ph ne 1-800-732-4065 315-476-5151 Fax [phone] www. neida-air.c m
Owners Manual
W
O
O
D
M
A
G
A
Z
I
N
E

I. System Start-Up Information
1. Read the installation and maintenance instructions as well as the recommended
safety practices in this manual.
2. Install Ductwork completely before operating collector:
A. Seal ductwork with silicone sealant or duct tape.
B. Have Dust Bin in place and sealed.
3. Have licensed electrician wire Fan / Blower according to wire diagram on pg. 13
in this owners manual.
4. Have licensed electrician check current draw on motor with all gates open. Current
draw should not exceed maximum motor amperage. (OAS is not responsible for
damage to motors caused by improper installation, wiring or failure to follow these
directions.
Caution
The Direct Drive Fan / Bl wer makes the system t p heavy!
Use extreme care when setting the unit up!
Warning
If amperage is t high - shut d wn immediately!
(See tr ublesh ting secti n.)
Warning
D n t perate Fan / Bl wer unless Cycl ne and Dust Bin
are in place. M t r will ver heat!
Warning
Check amperage draw during perati n with all blast gates
pen. Make certain amperage is n t utside perating limit
indicated n m t r plate!
2
O.A.S. 2004
c
2HP C mmercial W d Dust C llect r Owners Manual

II. 2hp Commercial Configurations
1. No Filter - Vent Outside -
3. External Tube Filters -
2. External Cartridge Filter -
Cartridge Filter Media
1 Pleated Cartridge Filter 39 80 Sq. Ft. or 62 130 Sq. Ft.
Spun bonded Polyester BIA ZHI / 487 Test - Rated C
Captures 99.9% of Test Material between 0.2 - 2.0 microns
@ 11 FPM Face Velocity
D NOT rem ve fabric straps fr m filter.
Tube Filter Media
12 oz. Needle Felted Polyester Tube Filters, singed on the inside.
10 to 1 air to cloth ratio is recommended.
FT-19 Tube Filters / 18.8 ft of filter area / 12 dia. x 6 long /
7.5 - 8 ceiling height
FT-25 Tube Filters / 25 ft of filter area / 12 dia. x 8 long /
9 - 10 ceiling height
FT-31 Tube Filters / 30 ft of filter area / 12 dia. x 10 long /
12 ceiling height
BIA ZHI / 487 Test - Rated C
Captures 99.5% of test material between 0.2 - 2.0 microns @ 11
FPM face velocity.
1. No Filter
Caution:
If exhaust air is vented outside you must provide make up / return air.
Flue gases (carbon monoxide can be drawn into the shop from furnaces,
water heaters or other appliances.
2. External
Cartridge
Filter
3. External
Tube
Filter
2HP C mmercial W d Dust C llect r Owners Manual O.A.S. 2004
c
3
Silencer
included
/ Filter
Silencer Included with Filter

2HP C mmercial W d Dust C llect r Owners Manual O.A.S. 2004
c
4
III. General Specifications Fan Performance Curves
- Sleeve kit adds 7 (4 is minimum
- 35 gal. bin is 22 dia. x 22.5 h / 55 gal. bin is 22 dia. x 35.5 h
- Several Filter Options Available- Galvanized steel construction
- The collector can be hung on the wall, from the ceiling, or free standing support using
the 11 ga. angle iron ring at the top
(See assembly instructions
2.0 hp
Height without
Dust Bin
Cyclone
Diameter
Inlet
Diameter
Weight without
Dust Bin
TEFC Baldor
Motors
SF 1.15 / F4 Class
115v / 20 amps
208 - 230v /
11.4 - 10 amps
Thermal Overload Protection
64.25 21 7
Approx. Wt.
122 lbs.
w/o drum or filter
Static pressure and volume together determine
a fans performance. Several factors, such as
layout of ductwork and diameter of openings,
can affect a fans performance.
2hp Commercial System
1405 max cfm
Industrial TEFC 2hp motor
115v / 20 amps. 208 - 230v / 11.4 - 10 amps
18 gauge galvanized cyclone & integral blower
7 dia. inlet / rectangular outlet
13.5 dia. x 4 wide cast aluminum fan wheel
back inclined non-sparking, non-ferrous balanced to .3 mil
Sound 74 -75.5 dB with Filter and Silencer
2hp Commercial System Performance Curve
1600
1400
1200
1000
800
600
400
200
0
Air Flow (CFM
Static Pressure @ Cyclone Inlet
012345 7689
1405 1349
1251
1146
954 779
551
Max. CFM 1405
1405
1349
1251
1146
954
779
551
1.86
1.82
1.81
1.77
1.74
1.61
1.40
HP
(Output
CFM

5
2HP C mmercial W d Dust C llect r Owners Manual O.A.S. 2005
c
IV. Dimensions
For Minimum Mounting Heights
*Dimensi ns subject t slight variati n in manufacturing.
2hp Outlet Detail
Outlet
C
4 13/16
6.5
7.5
Outlet - Can be rotated
independent of the inlet.
Inlet
21
23
Rotation
Top View
21.75
Bolt
Circle
24.5
Outlet
Wall Mounts
13 (39
18 (62
Cyclone
Barrel
1.5
30
2.625
12
12
External Tube Filter
Number of
tubes depends
on mounting
height and
filter area
required.
FTS060000 - 72 L
FTS080000 - 96 L
FTP080000 with zippers 96 L
(No 5 gal. bucket needed.
FTP100000 - 120 L
Note: Check drum height, it will
affect your bracket height.
Always check the
actual system
height to
determine your
mounting height.
4 (62
25.125
52.5 (62 Filter 50 (39 Filter
9
10.5
16.5
26.5
6.5 Flex
22.5 - 35 gal. 34 - 55 gal.
85 - 35 gal. / 94 - 55 gal.
2 Collar
on
drum
7 Dia.
2 Collar
1 for 62 Filter
54
4 13/16
Overall - 92.5 (35 gal. & 39 Filter 96(35 gal. & 62 Filter / 105.5 (55 gal.
80 w/ 55 gal. drum
71 w/ 35 gal. drum
To lowest Bracket hole.
35 gal. - 70.5
55 gal. - 79.5
6 (39
Included
Internal
Silencer
39 Filter
or
62 Filter
52.5 (62 Filter 50 (39 Filter

6
V. General Tube Filter Layout Dimensions
8 hole double wide plenum
32 3/4 wide x 76 long x 12 high
with 1/4 flange
7 hole single wide plenum
15 wide x 112 1/2 long x 12 high
6 hole double wide plenum
32 3/4 wide x 62 long x
12 high
5 hole single wide plenum
15 wide x 82 1/2 long x 12 high
4 hole single wide plenum
15 wide x 68 1/2 long x 12 high
5 hole double wide plenum
32 3/4 wide x 62 long x
12 high
4 hole double wide plenum
32 3/4 wide x 48 long x
12 high
Offset
Inlet
Plenum
(Plenum
will be 1 1/4
off wall
27.125 8 12 18
2hp Cyclone
with Fan
Plenum can g t the right r left f the cycl ne.
Many c nfigurati ns are p ssible.
Inlet
Outlet
Outlet can be r tated and
riented independent f inlet.
Square to Round
Transition
w/ gasket
Silencer Large Radius
Adjustable Elbow
w/ centerline radius
of 1.75
13
External Filter
Plenum 39
24.875
2 HP Cycl nic W d Dust C llect r Owners Manual O.A.S. 2004
c
18
External Filter
Plenum 62
27.375

7
2HP C mmercial W d Dust C llect r Owners Manual O.A.S. 2004
c
Plenum Box
Standard 5 gallon buckets
(Not provided with system
Tube Filters
16oz. Needle Felted Polyester
1 Micron Filtration
HC - 12
Hose Clamps
HC - 12
Hose Clamps
Fan / blower exhaust air is blown into chamber
evenly dividing the air between the filter bags
U.S. TEFC Motor
Angle Iron Wall
Brackets
support fan
housing and
cyclone
Cyclone inlet
7 dia. - 2hp
8 dia. - 3hp
Connect to main duct
run out to
woodworking
machines
Cyclone
Barrel
Cyclone Preseparator
separates 99% of the
wood waste from the
air stream. Eliminates
wear on the fan wheel
and maintenance on
the filter.
Cone
Flex Hose
Dust Bin
Light weight 35 or 55
gal. fiber dust bin. Steel
drum available for
outside applications.
Note: For cyclonic preseparation there must be an air tight seal between cyclone and dust
container. Dust bin must be located vertically under cyclone, material drops down by gravity.
Hose Clamp
Hose Clamp
VI. General Assembly
Vortex Tube
Fan
Blower
Outlet
Band Clamp
Rubber Gasket
Rubber Gasket
Band Clamp

2HP C mmercial W d Dust C llect r Owners Manual O.A.S. 2004
c
11.25
VII. Bracket Assembly
1. You must determine the direction the fan outlet will point to
proceed with this mounting assembly. The collector will seem
quieter if the outlet is aimed away from the area people tend to
work. Slots in the brackets are .406 x 1.00
Note: Bolts included to mount bracket to collector. Hardware
NOT included to mount to wall.
2. Mount wall bracket. For wall mounting, the bolt centers on
the brackets are at 16 to accomodate most wall stud spacing.
See Fig. 1 & 2. Use a Level to ensure straightness.
3. Attach bracket to wall with lag screws, concrete anchors, or
other suitable hardware. See Fig. 2 & 3. N te: When installing
the brackets n a c ncrete wall, m unt 2 x 4s between wall and
brackets t stabilize and dampen vibrati n.
4. Position Angle Ring holding the fan housing over bracket.
Line up one hole in Ring with hole in each bracket at desired
rotation of outlet. If rotation you desire does not correspond to
an existing hole in Angle Ring, drill new ones. Use three 3/8
bolts (included with washers & lock washers to secure the fan.
See Fig. 4.
6. Attach tightly with bolts. See Fig. 4.
1
.406 x 1.00
Note: Please do not install an Oneida Dust Collection System alone. Competent
assistance is advisable. Units are heavy!
4
* Optional Mounting Direction
8
3 3/16
16
23 1/4
12 Ga.
2
3
Level
80 w/ 55 gal. drum
71 w/ 35 gal. drum
Height to lowest hole.

O.A.S. 2004
c
2HP C mmercial W d Dust C llect r Owners Manual
9
VIII. General Assembly Instructions - All Models
1. Wire motor according to wiring diagram on page 13. Use
a cord rated for a minimum of 20 Amps. Make sure the cord
you use is rated for the same power as the motor. Always
follow motor plate diagram and wire for correct rotation. (See
Wiring diagram secti n)
2. Secure fan assembly to Bracket (See Bracket assembly
Pg. 8 then attach cyclone barrel with ductwork clamp ring to
the fan assembly. Check to see if rubber seal is attached to
barrel top. Align the inlet of the cyclone in the proper direction
for the system. See Fig. 1.
3. Attach the cone to the barrel with the metal clamping ring.
Lightly tighten the ring bolt. It is important that there is no air
leakage between the cone and barrel of the collector. There
should be a black rubber seal between the cone and barrel.
See Fig. 2
4. Attach flex hose to bottom of collector and to lid of dust bin.
Securely fasten hose clamps. Cut excess length of flex hose
if needed. Longer flex hoses are available for installations
requiring more height. There must be an air tight seal between
the collector and dust bin. See Fig. 3
5. Make sure the dust bin lid sits securely and the rubber
gasket on the bin lid is in place on the barrel. Maintain an air
tight seal between cyclone and dust bin to prevent motor from
overheating
due to over amperage draw.
6. Attach the ductwork from the woodworking machines to the
inlet of the collector.
7. For External Cartridge, Tube Filter or No Filter models see
following pages 10 and 11.
8. On external filter models, attach Filter Plenum Assembly or
External Cartridge Assembly with 4 bolts. See Filter Assembly
Secti n, pages 10 & 11 f r details.
Fan
Assembly
Cyclone
Barrel
Clamp
Ring
1
3
Collector
Hose Clamp
Hose Clamp
Flex Hose
Dust Bin
2Barrel
Cone
Clamp
Ring
Wiring should be done by a licensed electrician!
Rubber
Seal
Outlet
Inlet
IMPORTANT:
Do not operate the collector until the dust bin is in place
and the connector is air tight or motor damage could result!
Stay clear of fan exhaust hile collector is operating.
Quick
Release
Clamp
Rubber
Seal