Oneida Air Systems Dust Deputy AXD002030 User manual

Pat. # 7,282,074
The Original
Super Dust Deputy Owner’s Manual
AXD002030
Made in the USA
ZBM000036SDDM / 1-2014
1.800.732.4065 www.oneida-air.com
Fire Hazards and Codes
Warning! Explosion and re hazard! Never vacuum ammable uids or gas, oil, alcohol, solvents, etc. Do not
operate near ammable uids or gas. Never vacuum warm uids or materials at more than 140 deg. F (60 deg.
C), such as burning cigarettes, ashes, glowing coals, etc.
Warning! Do not vacuum hazardous / carcinogenic dust unless a HEPA lter is installed.
Always keep lter cartridge clean so the vacuum operates properly.
Empty Dust Deputy waste can frequently. Never leave ammable material in your Dust Deputy or shop vacuum.
Oneida Air Systems makes every effort to accurately represent our products and prices, however OAS
reserves the right to make changes to products and prices at any time. As a manufacturer, OAS reserves
the right to change product specications at any time in an effort to achieve better quality products.
Returned Goods Policy
Buyer must inform O.A.S. of any shortage or damage, by so noting in writing, on the freight delivery bill prior
to signing to indicate receipt of shipment. All claims, including claims covered under the limited warranty, are
subject to inspection and investigation by O.A.S. O.A.S. reserves the right to inspect, investigate all returned
products before Buyer’s claim is settled. All products returned for a cash refund must be unused, resaleable and
purchased within 30 days. There are no refunds on ex hose, custom made components or partial kit items. Kits
must be returned in full (all components) for credit. There will be a 25% restocking fee applied to any returned
items. Buyer must call and get an RMA (Return Authorization Number). Merchandise must be shipped
to us prepaid.
Limited Warranty
Terms & Conditions
Oneida Air Systems™ warrants the products manufactured by Oneida Air Systems, for a period of 90 days or
more depending on the product, to the original purchaser from the date of purchase unless otherwise specied.
Purchaser is responsible for returning warranty items to OAS at their expense. All parts must be returned with
an OAS provided Returned Material Authorization Number (RMA#). Any shipment without an RMA will be
refused. Items not manufactured by Oneida Air Systems are limited to their own manufacturer’s warranties. All
electrical items such as magnetic starters, remotes, sensors, pumps and accessories are limited to 90 days.
Oneida Air Systems warrantees that the product will be free from defects in materials and workmanship. This
warranty does not apply to defects due directly or indirectly to misuse, negligence, accidents, abuse, repairs,
alterations, improper wiring or lack of maintenance. This is Oneida Air Systems sole written warranty and
any and all warranties that may be implied by law, including any merchantability or tness, for any particular
purpose, are hereby limited to the duration of this written warranty. Oneida Air Systems does not warrant or
represent that the merchandise complies with the provisions of any law or acts unless the manufacturer so
warrants. In no event shall Oneida Air Systems’ liability under this warranty exceed the purchase price paid for
the product and any legal actions brought against Oneida Air Systems shall be tried in the State of New York,
County of Onondaga.
ONEIDA AIR SYSTEMS SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR
PROPERTY OR FOR INCIDENTAL, AND CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES
ARISING FROM THE USE OF OUR PRODUCT.
Before Purchasing or Installing a dust collection system the buyer is cautioned to do so in accordance with
prescribed Federal, State, Local, OSHA, NFPA, and any other applicable codes or regulations relating to the
type of dust(s) you are collecting.
SOME TYPES OF DUST UNDER CERTAIN CONDITIONS HAVE THE POTENTIAL TO BE EXPLOSIVE.
Oneida Air Systems is not responsible for how the dust collector is used or installed. Dusts with deagration or
explosion risks, such as wood dust, may require additional safety equipment including but not limited to; vent-
ing, spark detection, suppression systems, back draft dampers or may require installation in an outside location
or in a protected area away from personnel. The customer assumes the responsibility for contacting their insur-
ance underwriter with regard to specic engineering controls or application requirements. (We suggest you
reference NFPA 664, 654 and 68 codes for more information) Oneida Air Dust Collection Systems may not be
suitable for some applications and are not designed to be used in explosive atmospheres. Oneida Air Systems
equipment should only be installed and wired by a licensed electrician following all applicable local and
national electrical codes.

System Start-Up Information
Read the installation and maintenance instructions as well as the recom-
mended safety practices in this manual and your shop vacuum’s owner’s
manual before assembling and using the Dust Deputy®.
Some dusts are highly ammable or explosive. Learn / know what you
are dealing with. Follow all local, state, federal & NFPA codes and
guide lines.
Safety Instructions to be Strictly Followed.
Wood dust mixtures are highly ammable and can be explosive.
NEVER introduce sparks or sources of ignition into collector.
1.) Dump drum after each use.
2.) Ground system. (See pg. 9) For added safety.
The Dust Deputy® is made from static dissipating plastic. Additional
grounding is recommended for increased safety. See grounding instruc-
tions.
Keep re extinguishers handy at all times.
Can be used for collecting non-ammable liquids.
Dispose of waste in a FIRE SAFE AREA.
NEVER leave wood dust in a building or vehicle.
Always read your shop vacuum owner’s manual for safety proce-
dures regarding the operation of your shop vacuum.
Do not vacuum, or use this Dust Deputy® near ammable or combus-
tible liquids, gases, or explosive dusts, such as gasoline or other fuels,
lighter uid, cleaners, oil-based paints, natural gas, hydrogen, coal dust,
magnesium dust, grain dust, aluminum dust, sugar dust, our dust or
gun powder.
Do not vacuum anything that is burning or smoking, such as cigarettes,
matches, or hot ashes or any hot substance!
To reduce the risk of health hazards from vapors or dusts, do not
vacuum toxic materials unless a HEPA lter is used. Do not use or store
near hazardous materials.
WARNING / SAFETY
1. 6.
Troubleshooting
Dust Deputy not separating well. (Only a tiny amount of dust should reach the
collector.)
Low air volume.
Material swirls in cyclone and won’t drop down into drum.
Air leak. Check cyclone ange / drum lid / barrel. Even small leaks will affect
performance.
Vacuum lter clogged. Blockage in hose.
Air leak in bottom of cyclone / drum lid or dust drum.
Large, bulkier material might swirl. Restart or temporarily cut off
air ow to drop material down.

Dimensions
Super Kit Contents Super Dust Deputy® - AXD002030
U.S. Patent #7,282,074
2.5.
Super Dust Deputy®- AXD002030
- Drum Cyclone 16” Cyclone - VXC160001 (1)
- Adapter Spiral 5” Dia. - DAS050000 (1)
- Roll of Gasket - 24”x 1/4”x 1/4” RGZ250250 (1)
- Bolts 1/4-20 x 3/4” Hex Head - AFS015920 (6)
- Washer Flat 1/4”- AFW025000 (6)
- Whiz Lock Nut 1/4”- AFT000005 (6)
- Owner’s Manual - ZBM000036SDDM
Accessories
DRL060500
DRL060400
DRL050400
DRL050300
SEK170601
6” to 5”
6” to 4”
5” to 4”
5” to 3”
17 Gal. Steel
Drum Kit
DHF030000
DHF040000
DHF050000
DHF060000
3” Dia.
4” Dia.
5” Dia.
6” Dia.
Sold in pre-cut lengths
of 5’ / 10’ / 20’
Sold in packs of ten.
You may need reducers depending
on the size of the dust ports on your
machines.
Other drums are available also.
Please check the website.
May be needed to connect 6” Flex
Hose to outlet.
1.5 mil. 16”x 14”x 36”
6” Adapter
AXD600300
DAO060000
Part #
Part #
Part #
Part #
Part #
Description
Description
Description
Description
Description
Heavy Duty Plastic Bags
Adapter
Flex Hose
Dust Drums
Reducers

3. 4.
General Assembly Instructions
2. Turn cyclone upside-down and place it on the oor or
other at surface. Turn drum lid over and align bolt holes in
lid with bolt holes in cyclone base. Put bolt through washer,
then put bolt and washer through lid from the underside
of lid and add another washer and attach with whiz nut.
Tighten nut and repeat with all six bolts. Thoroughly tighten
hardware to eliminate air leaks. (Fig. 2 & 4)
3. Put cyclone and lid on top of optional dust drum then
attach and seal with clamp ring. (Fig. 3)
1. Apply gasket around the inlet hole in the drum lid,
making sure that the gasket goes inside the bolt holes and
around the inlet hole. An air tight seal is extremely impor-
tant for good dust collection. Make sure ends of gasket
butt together and there are no gaps. (Fig. 1)
3.
2.
1.
4. When you attach the hose from your tool to the 5” inlet,
you may need to use a reducer depending on the size of
your tools’ dust colllection outlet.
4.
5.
5. Attach 6” hose to the Super Dust Deputy’s top outlet with
a hose clamp, then connect the other end to your collectors’
fan blower as shown in the diagram below.(Fig. 5)
6. Make sure there are no air leaks at the connections. Make
sure to check your dust drum frequently so you do not overll
it.
7. You may need to use an
adapter to connect the 6”
ex hose to outlet. See ac-
cessories page. (Fig.6)
#DAO060000
Bolt
Washer
Nut
Flange
Gasket
Drum Lid
6.
Accessories
- Super Cartridge Filter Retrot Kit
Catches the micro-ne dust.
Small footprint.
Quick clean out dust pan.
May be required for installation:
Elbows / Reducers
Flex Hose / Duct Hanger / Pipe Hangers
High Efciency Filter Cartridge / Dust Drum
Filter Cap with Holes for Hanging / Hardware
High Efciency Axtar Spun-Bonded Media
Teon-Like Coating to Facilitate Dust Cake Release
Filter Media Captures 99.9% of Test Material
from 0.2 - 2 Microns @ 11 FPM / Accredited,
Independent Lab Tested
*Oneida reserves the right to change or modify specs and
system appearance without notice. Actual system appearance
may vary.
Optional
FXK010039
FXK010000
39” L x 13” D / 7” Inlet / 95 Sq. Ft.
62” L x 18” D / 8” Inlet / 130 Sq. Ft.
Part # Description
Filter Media
Included
ASHRAE
Tested
7” or 8”
Holes for
Hanger
Straps
Holes for
Hanger
Straps
Patented
Internal
Silencer
Quick Release
Dust Pan
Super
Cartridge
Filter
39”
or
62”
13”
or
18”
HEPA Filter Retrot Kit for
Single Stage Collectors.
Collector Not Included.
FXK011820 HEPA Filter Retrot Kit
Part # Description
Keep your shop clean by preventing ultra-ne dust from
blowing out of your single-stage bag collector and into your
shop air.
Add a best-in-ltration GE H12 HEPA lter to your current
single stage dust collector.