Oneida Air Systems Deluxe Dust Deputy User manual

Rev: 04/11/2022 Doc. # ZBM000050
Appearance may vary slightly
Dust Deputy Deluxe
10 Gallon
# AXD250010
U.S. Pat.
6833016
RE40048
7282074

Oneida Air Systems2
System Start-Up Information
1. Do not vacuum anything that is burning or smoking, such as cigarettes,
matches, hot ashes, or any hot substance!
2. Do not vacuum (or use this cyclone near) ammable or combustible
liquids, gases, or explosive dusts, such as gasoline or other fuels,
lighter uid, cleaners, oil-based paints, natural gas, hydrogen, coal dust,
magnesium dust, grain dust, aluminum dust, sugar dust, our dust or
gun powder.
3. To reduce the risk of health hazards from vapors or dusts, do not
vacuum toxic materials unless a HEPA lter is used. Do not use or store
near hazardous materials.
4. Dust can be ammable and explosive. Some dust can be toxic or cause
allergic reactions.
5. Wood dust mixtures are highly ammable and can be explosive.
NEVER introduce sparks or sources of ignition into collector.
a. Empty drum after each use.
b. Ground system.
6. NEVER leave wood dust in a building or vehicle.
7. Keep re extinguishers handy at all times.
8. Can be used for collecting non-ammable liquids.
9. Dispose of waste in a FIRE SAFE AREA.
READ THE SAFETY PRACTICES INSTALLATION
AND MAINTENANCE INSTRUCTIONS AND YOUR
WET/ DRY VACUUM’S OWNER’S MANUAL BEFORE
ASSEMBLING AND USING THE DUST DEPUTY
SOME DUSTS ARE HIGHLY FLAMMABLE OR
EXPLOSIVE. LEARN/ KNOW WHAT YOU ARE
DEALING WITH. FOLLOW ALL LOCAL, STATE,
FEDERAL & NFPA CODES AND GUIDELINES.

3oneida-air.com
System Dimensions
Nominal dimensions shown. Dimensions subject to slight
variations in manufacturing.
19"
483 mm
34-1/4"
870 mm
32 -7/16"
824 mm
19 -3/16"
488 mm
15-5/8"
397 mm
13-3/4"
349 mm
2-1/2" O.D.
64 mm
2-5/16" I.D.
58 mm
8-1/2"
216 mm
7-5/8"
194 mm
2-5/16" I.D.
58 mm

Oneida Air Systems4
System Contents
ID Part number Part description Qty
A VXC150225 Anti-Static Cyclone 1
B AXG000004A* Cyclone Gasket 1
C AHX000016* Cyclone Hardware Pack 1
C1 AFS015920* 1/4" - 20 x 3/4" Hex Head Bolt 6
C2 AFW025000* 1/4" Flat Washer 6
C3 AFT000005* 1/4" Whiz-Lock Nut 6
D SEX100000 Steel Lid for 10 Gallon Drum 1
E SES100000 10 Gallon Steel Drum with Clamp 1
F SDD000004* Dolly Legs 3
G AFS015800* 1/4"-20 x 1/2" Hex Head Bolt 3
H AFT000005* 1/4" Whiz-Lock Nut 3
I RBB000010 * Retainer Clips Pack of 6 1
J AHK000012* Caster Hardware Pack 2
J1 ————* Nylock Nuts 3
J2 ————*† Washers 6
J3 ————* 38mm Polypropylene Casters 3
K VFA050015 * Metal Grounding Tape 30"
L AXD250066 2.5" x 5.5' Wire-ReinforcedVacuum Hose 1
Please unpack the parts carefully and conrm you have received each
item listed here.
* Combined inside hardware package (AHX250010).
†Additional washers are included in your hardware
package (AHK000012).

5oneida-air.com
Please unpack the parts carefully and conrm you have received
each item listed here.
System Contents (Cont.)
B
A
E
D
J1
J2
J3
J
CC1 C2
C3
K L
F
I
G
H
×2

Oneida Air Systems6
You will need the following:
• 7/16" Open End Wrench
• Wet/Dry Vacuum
• Vacuum Hose
• Vacuum hose adapters
• 1/2" Nut Driver
Assembly Instructions
FIG. 1a
FIG. 1b
Arrange the Dolly Legs (F) in a descending stack as shown
in [FIG. 1a] and [FIG. 1b].
1
Note: Due to a variety of factors associated with the molding process,
the base of the Dust Deputy 2.5 cyclone may appear warped rather
than perfectly at. is is normal and does not impact performance
as long as the cyclone is installed according to these instructions.

7oneida-air.com
G
H
Assembly Instructions (Cont.)
FIG. 2a
FIG. 2b
Secure Dolly Legs (F) together using three Bolts (G) and
three Whiz-Lock Nuts (H) as shown in [FIG. 2a] and [FIG.
2b].
2

Oneida Air Systems8
Assembly Instructions (Cont.)
Thread each of the six Casters (J3) through the Dolly Leg
Assembly (F) and a Retainer Clip (I). Secure together
using six Nylock Nuts (J1) [FIG. 3a] [FIG. 3b].
Note: For ease of assembly, hardware should be nger
tightened when connecting the Drum (D).
3
FIG. 3a
FIG. 3b
F
J1
I
J3

9oneida-air.com
Assembly Instructions (Cont.)
Place the Drum (E) onto the Assembled Dolly [FIG. 4a],
then slide the Retainer Clips (I) into position over the
bottom lip of the drum to securely hold the container in
place. [FIG. 4b] Start by tightening two opposing Nylock
Nuts (J1) until the lip of the drum is fully secured. [FIG.
4c] Then repeat the process for the next two opposing pairs,
making sure that the drum is centered as you go.
4
FIG. 4a
FIG. 4b
FIG. 4c

Oneida Air Systems10
Turn Cyclone (A) upside-down. Place Gasket (B) on the
base of the Cyclone and the topside of the Lid (D) against
Gasket (B) and align all the holes. Secure Cyclone, Gasket,
and Lid together using six Bolts (C1), six Washers (C2), and
six Whiz-Lock Nuts (C3) as shown in [FIG. 5].
Note: oroughly tighten hardware to eliminate air leaks.
5
C1
C2
C3
FIG. 5
Assembly Instructions (Cont.)