Optex OA-PRESENCE TN User manual

The actual detection area may become smaller depending on the ambient light, the color / material of
the object or the floor as well as the entry speed of the object.
The sensor may not be activated when the entering speed of the object or a person is slower than
50mm / sec. or faster than 1500mm / sec.
NOTE
Mounting height : 2.2m(7'3")
Angle adjustment : +6°
Sensitivity : Middle
: Emitting spots
: Detection area
: Emitting spots
(can be eliminated)
Test conditions required by EN 16005
Floor :Grey paper
Detection object : EN 16005 CA reference body
Sensitivity : Middle
Speed of detection object : 50mm / sec.
To comply with EN 16005, make sure that the detection area is within the values of the chart below.
Detectionarea
The chart shows the values at depth angle +6°
Emitting area
A
X
E
G*
2.20 (7'3")2.00 (6'7")
0.25 (10")
1.12 (3'8")
2.65 (8'8")
3.00 (9'10")
0.34 (1'1")
1.53 (5')
3.60 (11'10")
0.23 (9")
1.02 (3'4")
2.41 (7'11")
The values above are those of the Detection area when tested referring to the test conditions of EN 16005.
(The emitting area is as shown in Emitting area above.)
*: When installed at higher than 3.0m(9'10"), EN 16005 requirements are fulfilled only within the area width "G"
of 3.6m(11'10").
[m(feet,inch)]
A
E
F
G
0
1.0
(3′3")
1.0(3′3")
1.0
(3′3")
2.0
(6′7")
2.0
(6′7")
2nd row
BC
D
A
B
C
D
E
F
2.20 (7'3")
0.25 (10")
0.39 (1'3")
0.65 (2'2")
1.33 (4'4")
2.70 (8'10")
0.31 (1')
3.00 (9'10")
0.34 (1'1")
0.48(1'7")
0.80 (2'7")
0.53 (1'9")
0.89 (2'11")
1.63 (5'4") 1.81 (5'11")
2.50 (8'2")
0.28 (11")
0.44 (1'5")
0.74 (2'5")
1.51(4'11")
2.00 (6'7")
0.23 (9")
0.35 (1'2")
0.59 (1'11")
1.21 (3'12")
2.05 (6'9") 2.51 (8'3") 2.79 (9'2")2.32 (7'7")1.86 (6'1")
G 2.78 (9'1") 3.40 (11'2") 3.79 (12'5")
3.50 (11'6")
0.39 (1'3")
0.61 (2')
1.03(3'5")
2.11 (6'11")
3.25 (10'8")
4.42 (14'6")3.15 (10'4")2.52(8'3")
[m(feet,inch)]
X
Mounting
surface
1st row
OA-PRESENCE TN
DETECTION AREA

Model
Cover color
Mounting height
Detection area
Detection method
Depth angle adjustment
Power supply (*1)
Power consumption
Operation indicator
Safety input
Safety output
Operating temperature
: OA-PRESENCE TN
: Silver / Black
: 2.0 (6'7") to 3.5m (11'6")
: See DETECTION AREA
: Active infrared reflection
: -6 to +6°
: 12 to 24VAC ±10% (50 / 60Hz)
12 to 30VDC ±10%
: < 1W (< 2 VA at AC)
: See Operation indicator table
: Opto coupler
Voltage 5 to 30VDC
Current 6mA Max. (30VDC)
: Opto coupler (NPN)
Voltage 5 to 50VDC
Current 100mA Max.
Dark current 600nA Max.
(Resistance load)
: -20 to +55°C (-4 to 131°F)
The specifications herein are subject to change without prior notice due to improvements.
NOTE
Operation indicator table
*1 : The sensor has to be connected to a door system which has a SELV circuit.
*2 : Overcurrent protection with less than 2A.
Operating humidity
Noise level
Output hold time
Response time
IP rate
Category
Performance level
ESPE
Weight
Accessories
: < 80%
: < 70dBA
: < 0.5sec.
: < 0.3sec.
: IP54
: 2 (EN ISO13849-1:2015)
: d (EN ISO13849-1:2015)
: Type 2
: 250g (8.8oz )
: 1 Operation manual
2 Mounting screws
1 Mounting template
1 Area adjustment tool
1 Cable 3m (9'10")
( 8×0.22mm² AWG24 ) (*2)
1sec. 1sec.
Stand-by (Installation mode)
Stand-by (Operation mode)
Setting error
Signal saturation
Sensor failure
1st row detection
2nd row detection
Status
Green
Red & Green blinking
Slow Green blinking
Fast Green blinking
Yellow
Red
Operation indicator color
Red blinking
OA-PRESENCE TN
SPECIFICATIONS

38(1 1/2")
61(2 3/8")
267(10 1/2")
125(4 15/16")
36(1 7/16") 43(1 11/16")
7.5(5/16")
[mm (inch)]
OA-PRESENCE TN
DETECTION AREA