ORiNG EN50155 User manual

Quick Installation Guide
Version 1.0
Quick Installation Guide
Introduction
PRINTED ON RECYCLED PAPER
Q I G
TRGPS-9084GT-M12X-BP2-MV is a managed Gigabit Ethernet switch with
8 Gigabit PoE-enabled ports and 4 Gigabit non-PoE ports in M12
connector. The non-PoE ports act as two sets of bypass ports to ensure
constant network connectivity when power outage or node failure occurs.
The switch supports various Ethernet redundancy protocols such as O-Ring
, O-Chain and MSTP (RSTP/STP compatible) to protect your mission-
critical applications from network interruptions or temporary
malfunctions. With EN50155 compliance and M12 connectors, the
device is a perfect choice for rolling stock applications.
Package Contents
Installation
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative
for assistance.
Preparation
Before you begin installing the device, make sure you have all of the
package contents available and a PC with Microsoft Internet Explorer 6.0 or
later, for using web-based system management tools.
Elevated Operating Ambient: If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow: Make sure the amount of air flow required for safe
operation of the equipment is not compromised during installation.
Mechanical Loading: Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Circuit Overloading: Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when
addressing this concern.
Safety & Warnings
For pin assignments of power, console and relay output ports, please refer to the following tables.
Contents
TRGPS-9084GT-M12X-BP2-MV
Pictures Number
1
Console Cable 1
Dimension
Panel Layouts
Front View
1. Reset button
2. Power status LED
3. R.M. status LED
4. Ring status LED
5. Fault LED
6. Power connector
7. Relay output port
8. Console port
Wiring
Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the grounding pin on the power connector to the grounding
surface prior to connecting devices.
Power port pinouts
The device supports two sets of power supplies and uses the M12 S-
coded 5-pin female connector on the front panel for dual power
inputs.
Step 1: Insert a power cable to the power connector on the device.
Step 2: Rotate the outer ring of the cable connector until a snug fit is
achieved. Make sure the connection is tight.
Relay output port pinouts
Relay N.C.
3A@24VDC
Network Connection
The switch has eight 10/100/1000Base-T(X) PoE and four 10/100/1000Base-T(X) non-PoE
Ethernet ports in the form of M12 connector. Depending on the link type, the switch uses CAT 3, 4,
5,5e UTP cables to connect to network devices (PCs, servers, switches, routers, or hubs). Please
refer to the following table for cable specifications.
TRGPS-9084GT-M12X-BP2-MV
TRGPS-9084GT-M12X-BP2-MV 1907-2-29-TRGPS9084GTM12XBP2MV-1.0
S w i tc h
E N 5 0 1 5 5
EN50155 Rack-mount managed
Gigabit PoE Ethernet switch
I N D U S T R I A L
The switch uses the M12 A-coded 5-pin female connector
on the front panel for relay output. Use a cable with an M12
A-coded 5-pin male connector to connect the relay. The
relay contacts will detect user-configured events and form
an close circuit when an event is triggered.
Cable
Type
Max. Length
Connector
10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft)
8-pin female M12
X-coding connector
100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft)
8-pin female M12
X-coding connector
1000BASE-T Cat. 5/Cat. 5e 100-ohm UTP UTP 100 m (328 ft)
8-pin female M12
X-coding connector
For pin assignments of the Ethernet ports, please refer to the following tables.
Rack-mounted kit (L&R) 1
Console port pinouts
RSVD
RXD
RS-23 2, 115200bps, 8, N , 1
GND
TXD
N.C.
V1+
V1-
N.C
CD 1
QIG 1
Rack-Mount
N.C.
Pow er
72~110 VDC
Rel ay Con sole
Res et
LNK /ACT LNK /ACT
PoE
Spe ed
TRGPS-908 4GT- M12X-BP 2-M V
Spe ed
Rin g
Fau lt
R.M
PWR
G1 G2 G3 G4 G 5 G6 G7 G8 G 9
G9 G11G10 G 12
G10 G11 G1 2
Powe r
Fail ure
Bypa ss
1.BI _DA+/ PoE Vout +
2.BI _DA- /P oE Vout+
3.BI _DB+/ PoE Vout -
4.BI _DB- /P oE Vout-
G1~ G8 G9~G1 2G1~ G12
1.BI _DA+
2.BI _DA-
3.BI _DB+
4.BI _DB-
5.BI _DD+
6.BI _DD-
7.BI _DC-
8.BI _DC+
5.BI _DD+
6.BI _DD-
7.BI _DC-
8.BI _DC+
1
2
5
3
4
67 8
9. PoE-enabled Gigabit Ethernet ports
10. Link/ACT LED for PoE-enabled Gigabit ports
11. PoE indicator for PoE-enabled Gigabit ports
12. Speed LED for PoE-enabled Gigabit ports
13. Non-PoE Gigabit Ethernet ports with bypass
14. Link/ACT LED for non-PoE Gigabit ports
15. Speed LED for non-PoE Gigabit ports
910 11
12
13 14
15
Rack-mounting
Step 1: Install left and right front mounting brackets to the switch using 4 M3 screws on each side
provided with switch.
Step 2: With front brackets orientated in front of the rack, nest front and rear brackets
together. Fasten together using remaining M4 screws into counter sunk holes.
Step 3: Fasten the front mounting bracket to the front of the rack.
6
5
7
3
2
1
8
4
10/100/1000Base-T(X) M12 X-coding
Pin No.
Pin Definition
#1
BI_DA+
#2
BI_DA-
#3
BI_DB+
#4
BI_DB-
#5
BI_DD+
#6
BI_DD-
#7
BI_DC-
#8
BI_DC+
10/100/1000Base-T(X) P.S.E. M12
X-coding
Pin No.
Pin Definition
#1
BI_DA+ with PoE Vout+
#2
BI_DA- with PoE Vout+
#3
BI_DB+ with PoE Vout-
#4
BI_DB- with PoE Vout-
#5
BI_DD+
#6
BI_DD-
#7
BI_DC-
#8
BI_DC+

Q I G Quick Installation Guide
PRINTED ON RECYCLED PAPER
Quick Installation Guide
Version 1.0
Q I G
Specifications
S w i tc h
E N 5 0 1 5 5
1. Launch the Internet Explorer and type in IP address of the device. The default static
IP address is 192.168.10.1
Follow the steps below to log in and access the system:
2. Log in with default user name and password (both are ).admin
3. After logging in, you should see the following screen. For more information on
configurations, please refer to the user manual. For information on operating the device
using ORing’s Open-Vision management utility, please go to ORing website.
Resetting
To restore the device configurations back to the factory defaults, press the button for a fewReset
seconds. Once the power indicator starts to flash, release the button. The device will then reboot
and return to factory defaults.
Configurations
After installing the and connecting cables, he green power LEDswitch t
should turn on. Please refer to the following tablet for LED indication.
Power
Redu nd ant Input Power
Physical Chara cteristic
Enclosure IP-30
Dimension (W x D x H) 44 0 (W ) x 32 5 (D ) x 44 ( H) m m (1 7. 32 x1 2. 8x1.73 inch)
Weight (g)
Environmenta l
-40 to 85 C (-40 to 185 F)
o o
Storage Temperature
5% t o 95 % Non-condensing
Operating Humidity
Regulatory App rovals
EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS),
EN61000-4-8, EN61000-4-11
EMS
IEC60068-2-27
Shock
IEC60068-2-32
IEC60068-2-6
Vibration
Free Fall
MTBF
EN60950-1
Safety
Fault Contact
Relay Relay output to carry capacity of 3A at 24VDC on M12 connector (5-pin M12 A-c od in g)
Overload Current Protec ti on
Revers e Polarity P ro tection Present
-40 to 75 C (-40 to 167 F)
o o
Operating Tempe rature
ORing Switch Model
10/100/1000 Base-T(X ) Ports
in M12 Auto MDI/MDIX with
P.S .E .
8 x M12 connect or (8 pin X-coding)
Physical Ports
Technology
Ethernet Standard s
IEEE 802.3 for 10Base-T
IEEE 802.3u for 100Base -TX
IEEE 802.3ab for 1000 Ba se -T
IEEE 802.3x for Flow co nt rol
IEEE 802.3ad for LACP ( Li nk A ggregation Contro l Pr otocol)
IEEE 802.1p for COS (Cl as s of Service)
IEEE 802.1Q for VLAN Tagging
IEEE 802.1w for RSTP (Rapid Spa nn ing Tree Pr ot ocol)
IEEE 802.1s for MSTP (M ul tiple Spanning Tree Protocol)
IEEE 802.1x for Authent ic ation
IEEE 802.1AB for LLDP (Li nk L ay er D iscovery Protocol)
IEEE 802.3at PoE specificatio n
8K
MAC Table
8
Priority Queues
10/100/1000Base -T( X) p orts
in M12 4 x M12 connect or (8-pin X-coding)
Store-and-Forward
Processing
Sw itch Properties
Sw itching latency: 7 us
Sw itching bandwidth: 24 G bp s
Max. Number of Ava ilable VLANs: 4094
VLAN ID ra nge: VID 1 to 4094
IGMP multicast grou ps : 128 for each VLAN
Port rate limi ti ng: User Define
Security Features
Device Binding securi ty f eature
Enable/disable po rt s, MAC based port securit y
Port b as ed network access contr ol ( 802.1x)
MAC- ba sed authentication (8 02 .1x)
VLAN (802.1Q) to segr eg ate and secure network traffi c
Radi us c entralized password manag em ent
SNMPv3 encrypted au th entication and access s ec urity
Https / SSH enhance network s ec urity
Web and CLI authen ti cation and authoriz at ion
IP source guard
Software Fea tures
IEEE 802.1D Bridge, aut o MA C address learning/ ag ing and MAC address (st at ic )
MSTP (RSTP/STP comp at ible)
Redu nd ant Ring (O-Ring) wit h re co ve ry t ime less than 30ms
TOS/ Di ffserv supported
Quality of Service (802 .1 p) for real-time traffic
VLAN (802.1Q) with VLAN t ag ging and GVRP support ed
Guest VLAN
IGMP v2/v3 Snooping
Application based Q oS m an agement
DOS/DDOS auto preventio n
Port c on figura tion, status, stati st ics, monitoring, se cu rity
DHCP Server / Client suppor t
SMTP Client
NTP server
Network Redundancy
O-Ring
O-Chain
MSTP (RSTP/STP comp at ible)
PoE Ou tp ut Pow er
LED
Color
Status
Description
PWR Green On DC power module activated
R.M Green On Device operating in Ring Master mode
Ring Green
On Ring enabled
Blinking Ring structure is broken
Fault Amber On Errors occur (i.e. power failure or port malfunctioning)
10/100/1000Base-T(X) P.S.E Ethernet ports
LNK/ACT Green On Port is linked
Blinking Transmitting data
PoE Green On Power supplied over Ethernet
Speed
Green On Port is running at 1000Mbps
Amber On Port is running at 100Mbps
Green/Amber Off Port is running at 10Mbps
10/100/1000Base-T(X) Ethernet ports
LNK/ACT Green On Port is linked
Blinking Transmitting data
Speed
Green On Port is running at 1000Mbps
Amber On Port is running at 100Mbps
Green/Amber Off Port is running at 10Mbps
Up to 9.6K Bytes
Jumbo frame
RS-232 Serial Conso le Port RS-232 in 5-pin M12 connector with console cable. 11 52 00 bp s, 8, N, 1
Powe r Co nsumption(Typ.)
ORing Industrial Networking Corp.
Copyright© 2018 ORing
All rights reserved.
TEL: [phone]
FAX: [phone]
Website: www.oringnet.com
E-mail: [e-mail]
TRGPS-9084GT-M12X-BP2-M V
72~110VDC on 4-pin S-coded M12 connector
20 W (not include PoE output)
61 .6W
4,550g
Warranty
5 ye ar s
29 8,128 hours
FC C Part 15, CISPR (EN55022) class A, EN 50 15 5 (E N5 01 21 -3 -2 , EN 55 01 1)
EMI
Present
128Mbits
Flash Memory
1Gbits
DRAM Size
TRGPS-9084GT-M12X-BP2-MV EN50155 Rack-mount managed
Gigabit PoE Ethernet switch
I N D U S T R I A L
Rack-Mount
TRGPS-9084GT-M12X-BP2-MV
TRGPS-9084GT-M12X-BP2-MV