Osram RGBWA+UVIR Slimpar Series User manual

P25
RGBWA+UV IR Slimpar Series
User manual
P le a se rea d t he ins t r u ction s ca refu ll y before use

2
TABLE OF CONTENTS
1. S af ety I nst r uctions ..................................................................................................3-4
2. Technical Specifications ...........................................................................................5
3. How To Control The Unit ................................................................................... 6-8
4. shape .......................................................................................................................... 9
5. Trouble shooting ......................................................................................................10
6. Fixture Cleaning .......................................................................................................11
statement
The product has well capability and intact packing when leave
factory. All of the user should comply with warning item and manual, any
misuse cause of the damages are not included in our guarantee, and
also can not be responsible for any malfunction & problem owing to
ignore the manual.

3
1. S af ety I nst r uctions
Please keep this User Guide for future consultation. If you sell the unit to another
user, be sure that they also receive this instruction booklet.
 Unpack and check carefully there is no transportation damage before using
the unit.
 Before operating, ensure that the voltage and frequency of power
supply match the power requirements of the unit.
 It’s important to ground the yellow/green conductor to earth in order
to avoid electric shock.
 The unit is for indoor use only. Use only in a dry location.
 The unit must be installed in a location with adequate ventilation, at
least 50cm from adjacent surfaces. Be sure that no ventilation slots are
blocked.
 Disconnect main power before replacement or servicing.
 Make sure there are no flammable materials close to the unit while operating as
it is fire hazard.
 Use safety cable when fixes this unit. DO NOT handle the unit by taking its head
only, but always by taking its base.
 Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the
temperature is higher than this Unit surface temperature may reach up to 85℃.
DO NOT touch the housing bare-hand during its operation. Turn off the power
and allow about 15 minutes for the unit to cool down before replacing or serving.
 In the event of serious operating problem, stop using the unit
immediately.Never try to repair the unit by yourself. Repairs carried out by
unskilled people can lead to damage or malfunction. Please contact the
nearest authorized technical assistance center. Always use the same type
spare parts.

4
 DO NOT touch any wire during operation as high voltage might be causing
electric shock.
Warning:
 To prevent or reduce the risk of electrical shock or fire, do not expose the unit to
rain or moisture.
 DO NOT open the unit within five minutes after switching off.
 The housing, the lenses, or the ultraviolet filter must be replaced
if they are visibly damaged.
Caution:
There are no user serviceable parts inside the unit. DO NOT open the housing
or attempt any repairs yourself. In the unlikely event your unit may require
service, please contact your nearest dealer.
Installation:
The unit should be mounted via its screw holes on the bracket. Always ensure that
the unit is firmly fixed to avoid vibration and slipping while operating.
And make sure that the structure to which you are attaching the unit is secure
and is able to support a weight of 10 times of the unit’s weight. Also always use a
safety cable that can hold 12 times of the weight of the unit when installing the
fixture.
The equipment must be fixed by professionals. And it must be fixed at a place
where is out of the touch of people.

5
2. Technical Specifications
Light Sources:
5/7/12 Leds*6in1 8W
Beam Angle:25°
Power Voltage: AC 100-240V, 50/60Hz
Dimension: 225*70*220mm
Net Weight: 1.5 Kgs
Gross Weight:1.8Kgs
Control
DMX Channel: 10 Channel
Control Modes: DMX512,Master-Slave/Music mode/Auto Run
IR remote control
Construction
Display: Digital Display
Data In/Out socket: 3-pin XLR sockets
Power Socket: IEC power in/out socket
Protection Rating: IP20
Features
Dimmer: 0~100% smooth dimming
Fast, quiet operation

6
3. How To Control The Unit
Th e D M X512 is w id ely used in intellig ent ligh ti ng co n tr ol,with a DMX 512
controller.connect several lights together,dmx in and dmx out,
3 p in XLR co nn ectors : Pin 1: G ND , Pin 2: Nega tive s ig n a l (-), Pin 3: P o s itive s i gna l
(+)
Display:
MENU To select the programming functions
DOWN To go backward in the selected functions
uP To go forward in the selected functions
ENTER To confirm the selected functions
Set DM X Address Code
1 Press "Menu" to "Set DMX Address",and press"ENTER" keys to enter into
2 Show "Set DMX Address DMX Address:001",Press the "UP and DOWN"
keys to amended
3 Press "ENTER"keys to save and Exit,Press the"MENU"Keys does not save and
Exit

7
Display
Menu
→
→
→
Function
Addr
A001~A512
DMX mode
AUTO
AUT1
SP-1~SP-9
St00~St99
FADE
AUT2
SP-1~SP-9
St00~St99
Color Jump
changing
COLO
CO01~CO51
St00~St99
51 colors
STAT
red
r000~r255
St00~St99
0-255 to adjust the
brightness of colors
including strobe
effect
Gree
G000~G255
St00~St99
blue
b000~b255
St00~St99
whit
U000~U255
St00~St99
Ambe
A000~A255
St00~St99
PURP
P000~P255
St00~St99
SOUN
SOU1
SEN0~SEN9
Sound mode,adjust
mic senstivity
SOU2
SEN0~SEN9
SLAV
SLA
Slave mode
rEno
On~oFF
Turn on/off IR
receiver
Ver
10
Soft Version

8
DMX channel´s functions and values (10 DMX channels):
Mode/
Channel
Value
Function
1
Full Dimmer :
0-255
Intensity 0 to 100%
2
Red dimmer :
0-255
Intensity 0 to 100%
3
Green dimmer :
0-255
Intensity 0 to 100%
4
Blue dimmer
0-255
Intensity 0 to 100%
5
White dimmer
0-255
Intensity 0 to 100%
6
Ambe dimmer
0-255
Intensity 0 to 100%
7
PURP dimmer
0-255
Intensity 0 to 100%
8
1-255
strobe
9
0-50
dimmer
51-101
FADE
102-152
JUMP
153-203
Sound1
204-255
Sound2
10
0-255
SPEEED / Mic senstivity adjustment

9
4. IR Remote controller Operation
1.Key “Auto” is Auto Run mode. It is also the switch for AUT1 and AUT2 mode.
Press”+”,”-“to set its run speed.
2.Key “Sound” is Sound mode. It is also the switch for”SOUND1” and “SOUND2”
mode. Press”+”,”-“to set mic senstivity.
3.Key”DMX”. Press DMX key, the indicator light show Red color, continuously
press three-digit number (the number should be between001-512), then set DMX
add.Item run into DMX work mode
4.Key”Black Out” is the switch for tun on/Off
5.Key Red,Green,Blue,White,”9”,”8” is switch for RGBW Amber, UV color
6.Key”Jump” is for color jump changing, Press”+”,”-“to set the speed
7.Key”Fade”, fade mode, Press”+”,”-“to set the speed.
8.Key “Color” select color, Press”+”,”-“to select
9.Key”Flash”,strobe mode. Press”+”,”-“to set the speed.
Notice: If the item work in DMX mode, IR remote control funcation will not work;
IR remote control only work when item not work in DMX model

10
5. Trouble shooting
F ollo w ing a r e a few c o mm on p r oble m s th a t m a y occu r d uring ope r a tion . He r e a r e
s o m e s ug g es tion s fo r ea s y tr ou b leshooting :
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Ch eck th e c on nect ion of p owe r a nd m a in fu s e .
2. M eas ure th e m a ins volt a g e on th e m a i n co nn e ct o r .
3. Ch eck th e pow er on LED .
B. N o t responding t o D MX c on t ro ll er
1. D M X LED s h ou ld b e on. If no t, che ck D M X co n nectors, ca b l es to s ee if link
p r ope r ly .
2. If th e D M X LE D i s on a nd no r espons e t o th e c h a nn el, che ck th e a dd r ess
s etti ng s a nd D M X p ol a r ity .
3. If y ou h a ve i nter m ittent D M X s ig n a l p r oble m s , che ck th e p ins on c onn ecto r s or on
PCB of th e u nit or the p r ev iou s on e.
4. Tr y to us e a no th er D M X co ntroller .
5. Ch eck if th e D M X ca b le s r un ne a r or run a lon g s id e t o h ig h volta g e c a b les th a t
m a y c a us e d a m a g e or in terfer ence to D M X inter face circui t.
C . One of the cha nn el s is no t w o r k ing w el l
1. Th e s tep p er moto r m ig h t b e dam a g ed or the c a b le c on nect ed to th e PCB is
b r oken.
2. Th e m oto r ’ s d r ive IC on th e PCB m ig h t b e o ut of co ndition.