Oursson HB6060 User manual

Hand blender HB6060
Operation manual

Congratulations on purchasing the Oursson Hand Blender!

CONTENTS
5
6 Chapter1:Introduction
6 Safety Instructions
8 Recommendations
9 Complete set
10 Parts of the structure
11 Chapter2:Operation
11 Whiskattachment
11 Measuring cup
12 Nozzle for blending
12 Bracket for vertical mounting and storage
13 Chopper attachment
15 Operation
15 Power Control
16 Recommendations for grinding various products
17 Cleaning and Maintenance
17 Quick Clean
17 Mounting the wall bracket
18 Chapter3:Other
18 Specifications
19 Product Certification
20 Servicing

INTRODUCTION
6
Dangersymbol
A reminder to user about high voltage.
Warningsymbol
A reminder to user about the necessity
of operating exactly according to the instructions.
When using electrical appliances should take
the following precautions:
• Use the device according to the following
operation guide.
• Install the device on a stable surface.
• Use only the tools which are the included
in the product set.
• To protect against risk of electrical shock
do not put motor body, cord, or electrical
plug of the blender in water or other liquid.
If for some reason the water got into the
unit, contact an authorized service center
(ASC) OURSSON AG.
• For power supply use a power grid with
proper characteristics.
• Do not use the device in areas where
the air can contain vapors of flammable
substances.
• Never attempt to open the device by
yourself – it could possibly be the reason
of an electrical shock, can lead to product
malfunction and will invalidate the
manufacturer’s warranty. For repair and
maintenance, contact only authorized
service centers meant for repair of products
under the trademark OURSSON.
• When moved from a cool to a warm place
and vice versa unpack it before use and
wait 1-2 hours without turning it on.
• In order to prevent electrical shock do not
immerse the entire product or the wires into
the water.
220-240 В
SAFETYINSTRUCTIONS

INTRODUCTION
7
• Be particularly careful and cautious when
using the device near children.
• Do not touch any moving parts, as this may
cause injury.
• The power cord is specially made relatively
short in order to avoid the risk of injury.
• Do not allow the cord to hang over
the sharp edge of the table or touch hot
surfaces.
• Do not connect this device to a grid which
is overloaded with other appliances:
it can lead to the fact that the device
will not function properly.
• Do not install the device near gas and
electric stoves and ovens.
• After use, make sure to disconnect the
device from the power grid.
• Keep the device from bumps, falls, vibration
and other mechanical influences.
• Make sure to disconnect the device from
the power grid before cleaning or changing
accessories.
• Do not use the device outdoors.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge.
They can only use the device under the
supervision of the person responsible for
their safety, or after instruction on the safe
use of the device. Do not allow children to
play with the product.
• Use the product for its intended purpose.
• This product is intended only for use
in the home.
• If the power cord is damaged, it must be
replaced by a specialist from the authorized
service center ( ASC ) OURSSON AG
to avoid danger.
•
Do not use abrasive cleaning materials, organic
cleaning products (alcohol, gasoline etc.).

INTRODUCTION
8
• Do not operate without making sure
that the cap for chopping bowl is closed
correctly and firmly.
• Use only the parts included in the product kit.
• When cleaning the device it is allowed to
use a small amount of neutral detergent.
• Do not immerse the motor unit into water,
it may cause electrical shock.
• During operation, do not substitute the
blender blades close to hand, as well as
kitchen utensils to avoid injury and / or
damage to the instrument. Spatula can
be used only when the unit is turned off.
• To not dull knives, do not use the device
for crushing ice, coffee or a very solid
products, as well as for mixing solids.
• Before using the device, please read
the user manual. After reading, please
keep it for future use.
• All illustrations in this manual are schematic
representations of real objects, which may
differ from the actual images.
• To avoid injury before establishing knives,
put the chopping cup on a clean flat
surface.
RECOMMENDATIONS
NOTE! The operation of this device
in any case does not imply
the use of physical force to it,
as this may cause damage
to the product through the fault
of the user.

INTRODUCTION
9
COMPLETESET
Motor unit
Whisk attachment
Nozzle for blending
Chopper attachment 500 ml
Measuring cup 500 ml
Bracket for vertical mounting and storage
Operating manual with warranty card
1 pc.
1 pc.
1 pc.
1 pc.
1 pc.
1 pc.
1 pc.

INTRODUCTION
10
Blade for chopping
Chopping bowl
Adapter for whisk attachment
Whisk attachment
Measuring cup 500 ml
Cover lid
Bracket for vertical mounting and storage
4
5
6
7
8
9
2
3
4
5
6
7
9
8
10
11
12
13
14
1
1
2
3
12
13
14
10
11
PARTSOFTHESTRUCTURE
Speed Switch
On / Off button
Button for TURBO Mode
Motor unit
Nozzle for blending
Chopper
Cap for chopper

OPERATION
11
Used for whipping egg whites, creams, biscuit
dough, dough for pancakes, stirring desserts.
Nozzleassembly
Insert the motor unit in the nozzle and turn
it clockwise until it stops. Dip the whisk
in a bowl with food and turn on the blender.
It is comfortable to use the measuring cup
for whipping a small amount of products.
For best results, whisk a small amount of
ingredients at the same time. For example,
no more than four egg whites. Use a wide
bowl and move the whisk clockwise.
MEASURINGCUP
The maximum volume of glass - 500 ml.
Comfortable bowl for mixing or chopping
a small amount of ingredients. Do not mix
/ whisk in the measuring cup products of
more than 300 ml in order to avoid splashing.
Miscible / whippable products should not
be too hot, otherwise there is a risk of injury
from splashing.
Motor unit
Measuring cup
Whisk

Œß
WHISKATTACHMENT

OPERATION
12
NOZZLEFORBLENDING
Used for soups-purees, baby food, pies and
sauces.
Nozzleassembly
Insert the motor unit to the nozzle and turn
counterclockwise until it stops.
Œß
Motor unit
blade for chopping
Nozzle for
blending
Œß
chopping bowl

OPERATION
13
CHOPPERATTACHMENT
Used for the preparation of baby food, a small
amount of meat, chopping onions, nuts, garlic,
making pates, butter with additions etc.
Chopper attachment is not intended for liquid
foods.
Assembly
1. Set the blades on the pin located in the
center of the bowl for grinding. The blades are
sharp, be careful not to cut yourself, always
hold them by the plastic rod.
2. After installing the blades, put products in
the bowl and placing the lid on top of the bowl,
turn it clockwise until it stops. Make sure it
is properly closed (the ledge inside the bowl
should enter the deepening in the lid) and
tight.
3. Screw the motor unit into the lid clockwise
as well.
Œß
NOTE! Chop in the chopper only
boneless meat, carefully
removing the tendons; cut
the meat into small pieces.
Maximum meat portion for
minced meat – 200 gr.

OPERATION
14
закрыть
close
NOTE! To avoid injury before
establishing knives, put the
chopper bowl on a clean flat
surface. When disassembling
the blender first disconnect
the motor unit. Never remove
it with the lid.

OPERATION
15
OPERATION
Before first use, wash the blender (see «Quick
Clean»). The time when the device idles shall
not exceed 15 seconds.
Before assembling or removing nozzles
ensure that the device is unplugged from the
power outlet. Maximum time of continuous use
of the device with a whisk or chopper should
not exceed 1 minute, then you should turn off
the blender for 3 minutes.
Maximum time of continuous use of the device
with a whisk for whipping must not exceed
2 minutes, then you should turn off the blender
for 3 minutes. The consecutive alternation of
these two intervals will provide reliable and
trouble-free operation of the device.
1. Assemble the necessary attachment device
as described above.
2. Plug the device into a power outlet.
3. Select the required speed by setting its
speed switch. The blender has a smooth
speed control (from low speed to high).
Then press and hold the on / off button.
4. You can also turn on the blender by holding
down the Turbo Mode. In this case, the
device will operate at maximal speed all the
NOTE! The blades are very sharp,
be careful.
_+
н
и
з
к
а
я
с
р
е
д
н
я
я
в
ы
с
о
к
а
я
POWERCONTROL
The device is equipped with a smooth speed
control. To change the speed, use the slider from
low to high in a clockwise direction.
low
medium
high
time. The speed will not change even if you
change the position of the switch.
5. To switch off, release the Turbo Mode.
6. Unplug the power cord from the outlet.
7.  Then you can disassemble the device.
You can open the lid of the chopper after
removing the motor unit.
8. After using the blender, place it in the large
hole of the bracket.

OPERATION
16
Ingredients Maximum
amount
Time
ofchopping
Speed
Onion 200 gr ~ 20 sec from low
to medium
Parsley 30 gr ~ 20 sec TURBO
mode
Garlic 20 cloves ~ 20 sec from low
to high
Boiled carrots 200 gr ~ 15 sec from low
to high
Almonds/
hazelnuts 200 gr ~ 30 sec TURBO
mode
Walnut 200 gr ~ 25 sec
from
medium
to high
Parmesan cheese 250 gr ~ 30 sec TURBO
mode
RECOMMENDATIONSFORGRINDINGVARIOUS
PRODUCTS

OPERATION
17
QUICKCLEAN
If you want to wash quickly the nozzle before
the next use, lower the whisk attachment in the
measuring cup half filled with water, and turn on
the device for a few seconds.
MOUNTINGTHEWALLBRACKET
You can attach the wall bracket as follows:
1. Drill two holes in the wall, by strictly adhering to
the dimensions shown in the figure below.
2. Hammer two dowels in the holes. Fasten the
bracket to the wall using two screws.
CLEANINGANDMAINTENANCE
1. Disconnect the device from the outlet and
remove the nozzle.
2. Rinse the whisk attachment under running
water without the use of abrasive cleaners or
detergents. After washing, place the nozzle
vertically to dry it.
4 мм
48 мм
4 mm
48 mm
NOTE! Do not dip the upper part of
whisk attachment in water as
the lubrication of the bearings
inside can be flushed.
3. Wash the chopping bowl, the measuring cup,
the whisk attachment and the knives in warm
soapy water. Whisk attachment and chopper
bowl are not recommended to be washed
in the dishwasher, as this will destroy the plastic.
4. Wipe the device with a damp cloth. Never
immerse it in water because of the danger
of electrical shock.
5. Thoroughly dry all parts.
6. Attach the whisk attachment to the motor unit
and place it vertically in the wall bracket as
shown in the figure.
NOTE! The blades are very sharp,
be careful.

Other
18
Specifications
Model HB6060
Power consumption, W 600
Power parameters ~ 220-240 V; 50 Hz
Class of protection against electric shock II
Storage and transportation temperature from -25°C to +35 °C
Temperature of operation from +5°C to +35°C
Requirements for air humidity 15-75%
Dimensions of the device, mm 390х64х64
Weight, kg 0,86
NOTE! Only a qualified specialist from the authorized service center OURSSON AG
should make the repair of the hand blender.

OTHER
19

Other
20
TheproductiscertifiedinRussiabythe
certificationbodyofproducts:
РОСС RU.0001.11AE61
AUTONOMOUS NONCOMMERCIAL
ORGANIZATION OF EXPERTISE AND
QUALITY CONTROL CENTER CERTIFICATION
«EURO TEST»;
Registered address: 109147, Moscow, Small
Kalitnikovskaya street, 7, 1037700252314, tel. 8
495 229 5603, fax: [phone];
e-mail: euro t[email protected]
In the absence of a copy of the new certificate in
the box ask it fromthe seller.
Thisproductmeetstherequirementsof
normativedocuments:
СТБ МЭК 60335-2-14-2005,
ГОСТ Р 51318.14.1-2006 (СИСПР 14-1:2005),
ГОСТ Р 51318.14.2-2006 (СИСПР 14-2:2001),
ГОСТ Р 51317.3.2-2006 (МЭК 61000-3-2:2005),
ГОСТ Р 51317.3.3-2008.
Certificatenumber:ТСRU C-CH.
AE61.B.00037.
Validity: from 18/06/2012 to 06/17/2015.
Manufacturer:«OURSSON AG», Utoquai 39,
8008 Zurich, Switzerland.
FactoryAddresses: «Guangdong Midea
Microwave and Electrical Appliances
Manufacturing Co., LTD», No.6, Yong an Road,
Beijao, Shunde, Foshan, Guangdong, PRC.
PRODUCTCERTIFICATION