Panasonic ET-RFF200 User manual

Thank you for purchasing this Panasonic product.
■Please read these operating instructions and the projector operating
instructions carefully, and then use this product correctly.
■Please save this Operating Instructions for future use.
Model No. ET-RFF200
Replacement Filter Unit Commercial Use
Operating Instructions
ENGLISH
DPQX1007ZA/X1
Mainlterunit
Pre-lter

2 - ENGLISH
Before replacing the air lter unit
Thisproductconsistsoftwotypesoftheairlters(eachonepiece).
-Mainlterunit
-Pre-lter
Attention
zTurn off the power and disconnect the power plug from the wall outlet before you replace
the air lter unit.
zWhenreplacingtheairlterunit,makesurethattheprojectorisstable,andworkinan
environmentthatissafe,evenifyoudroptheairltercover,themainlterunitorthepre-lter.
zDonotputanythingintotheairvents.Doingsomayresultinmalfunctionoftheprojector.
Note
zIllustrationscontainedinthismanualthatshowtheprojectormaydifferfromtheactualobjects
they depict.
How to replace the air lter unit
Knob Main filter unit
Fig. 2
Tabs
Air filter cover Main filter unit compartment and the projector’s air intake port
Fig. 1
1) Turn off the power of the projector and set the <MAIN POWER> switch to
<OFF> and disconnect the power plug from the power outlet.
zWhenthepoweristurnedoff,beabsolutelysuretofollowtheprocedure
described
in “Switching off the projector” in the operating instructions of the projector.
2) Remove the air lter cover (Fig. 1).
zPullouttheairltercoverfromthehookoftheprojectorwhileslightlypushing
upwardthetabsoftheairltercoverandopenitinthedirectionofthearrowingure.
zWhenpullingopentheairltercover,besuretormlyholdtheairltercoverwith
yourhand.Openingtheairltercoverquicklymayresultinthecoverfalling.
3) Remove the main lter unit.
zPulloutthemainlterunitfromthetabsoftheprojectorwhileslightlypressingthe
knobatthecenteroftheframeattheconnectingterminalside(rearside)inward
asshownbythearrow,andremovethemainlterunit.(Fig.2)
zAfterpullingoutthemainlterunit,removeforeignobjectsanddustfromthemain
lterunitcompartmentandtheprojector’sairintakeportifthereareany.
4) Remove the pre-lter from the air lter cover.
zPutyourngerinthegrooveandremovethepre-lterfromtheclaws.(Fig.3)
z
Afterremovingthepre-lter,removeforeignobjectsanddustifthereareanyontheair
ltercover.
Replacing the air lter unit

ENGLISH-3
Replacing the air lter unit (continued)
Air filter cover
Groove to put the finger in
Pre-filter
Claws
Fig. 3
5) Attach the unused main lter unit to the projector.
zPerformStep3) in the reverse order.
zPushinthemainlterunitsecurelyuntilitclicksintoplace.
6) Attach the unused pre-lter to the air lter cover.
zThereisnospecicationofthefrontandbackforattachingthepre-lter.
zPutthepre-lterintotheclaws(3places)ononesideoftheairltercover(Fig.4),
and then push each portion slowly in the direction of the arrows into the claws
(3places)ontheotherside(Fig.5).Pleasemakesurethatthereisnodamageor
deformationatthecontactareasofthepre-lterwiththeclawswhenattachingit.
Air filter cover
Pre-filterClaws
Claws
Fig. 4 Fig. 5
7) Attach the air lter cover to the projector.
zPerformStep2)inthereverseordertoclosetheairltercover,andpushintheair
ltercoversecurelyuntilitclicksintoplace.
8) Connect the power plug, set the <MAIN POWER> switch to <ON>, and press the
power button <v/b> on the control panel or on the remote control to turn on the
power and start the projection.
9) Press the <MENU> button to display the main menu, then press as to select
[PROJECTOR SETUP].
10) Press the <ENTER> button.
11) Press as to select [FILTER COUNTER].
12) Press the <ENTER> button.
zThe [FILTER COUNTER] screen is displayed.
13) Press as to select [FILTER COUNTER RESET].
14) Press the <ENTER> button.
zThe [FILTER COUNTER RESET] screen is displayed.
15) Press qw to select [OK], then press the <ENTER> button.
zThelterusagetimeisreset.

W0316GC0 -ST
JDisposal
When discarding this product, please contact your local authorities or dealer and ask for
thecorrectmethodofdisposal.
WebSite:http://panasonic.net/avc/projector/
© Panasonic Corporation 2016
Panasonic Corporation
Replacing the air lter unit (continued)
Attention
zMakesurethatthemainlterunitandthepre-lterareproperlyattachedbeforeusingthe
projector.Iftheyarenotattached,theprojectorwillsuckindirtanddustcausingamalfunction.
zDisposeofthepackagingmaterialsproperlyafterunpackingtheproduct.
zDonotdisassemblethemainlterunit.
Note
zIfyouusetheprojectorwithoutattachingthemainlterunit,thelterindicatorblinksinredand
themessageappearsontheprojectedimageforabout30seconds.Turntheprojectoroff,and
thenattachthemainlterunitbeforeturningtheprojectoronagain.
zThereplacementcycleoftheairlterunitsvariesgreatlydependingontheusageenvironment.
zForproceduresonmaintainingtheairlterunit,refertotheoperatinginstructionssuppliedwith
the projector.