ParaBody 221 User manual

221 LEG PRESS ADAPTER KIT
FOR 220 GYM SYSTEM
/
WAI~LNING:
Readandfollow all directions
for eachstep to insure proper
assemblyof this product.
CLASS H
PART# 7031101
REV.B
USER’S GUIDE
I I
Version: 221101
Revision: 03/05/01

TABLE OF CONTENTS
SafetyStatement............. 2
GeneralNotes.................. 3
ToolsRequired................ 3
GymLayout..................... 4
Partslistl......................... 5
AssemblyInstructions..... 5;-10
GeneralMaintenance....... 11
WarrantyStatement.......... 12
ProdUctServices...::......... 13
Insei:~-RegistrationCard
I IMPORTANT SAFETY INFORMATION
THEREIS A RISKASSUMEDBYINDIVIDUALSWHOUSETHISTYPEOF
EQUIPMENT.TOMINIMIZERISKFOLLOWTHESERULES,!
"! Beforeusing, read ait the warningsandinstructions
on the useof this machineUseonly for intended
exercise. DONOTmodify the machine.
2. Obtain a medica!exambefore beginning any
exercise program.
3Keepbodyandc!,othingfreeofe,~":~,.~.... ..... gobje..’;:.s."
4. Inspect the machinebefore use. DONOTuseit if it
appearsdamaged.DONOTattempt to fix a broken or
jammedmachine¯ Notify your authorized ParaBody
dealer before useand haverepairs madeby an
authorizedservice technician.
5. Becertain that weightpin is completelyinserted.
Useonly the pin providedby the manufacturer.If
unsure, call your authorized ParaBodydealer.
6. Neverpin the weightsor propplate, into an eievated
position. DONOTusethe machineif foundin this
condition. DONOTattempt to fix. Notify your
authorized PataBodydealer¯
7 inspect cab!esandtheir connectlo~sbeforet~.ing
machine.PayFaitictfia~ a~.e~tionto ’:he cab!eends¯
DONO1"a~emptto fix. Notify your authel-ized
ParaBodydea{er before useand haverepairs rn~de by
anauthorizedservice technician.
8. Makesureall spring loadedpull pins are fully
engagedin the adjustmentposition andfully tighten
thumbscrewbefore use.
9. Children mustnot be allowednear this machine.
Superviseteenagers.
NOTE: In a continualeffort to improveourproducts,specificationsare subjectto change
©2001Life Fitness, a division of BrtmswickCorporation.All rights reserved.
ParaBodyis a trademarkof BrunswickCorporation
www.parabody.com

IIMPORTANTNOTES{
Please note:
* Thankyoufor purchasingthe ParaBody221LegPress AdapterKit. Please read these
instructions thoroughlyand keepthemfor future reference. This productmustbe assembled
ona flat, level surfaceto assureits properfunction.
* This productmustbe assembledon a flat, level surface to assure its proper function. DONOT
securelytighten anyfi’ameconnectionsuntil the entire framehas beenassembled,unless
otherwisestated.
[’Tools Requiredfor Assembly’"]
*9/16" wrench
*Ratchetwith 9/16" sockets
* Adjustable wrench
* Tape measure
[ ,, Bolt Length Ruler,
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
, , ’ II1iiii!!1
BOLT LENGTH
BOLT LENGTH RULER:
2[ i 1 ! 0.I I I II..I 5 I 6
I I II I t

7~
8~
1’ 2’ 3’ 4’ 5’ 6’ 7’ 8’ 9’
! Square= I’X 1’
MinimumRequired Usable Space
Length
Width
Height
=82 inches (208.5 cm)6’ 10"
= 71inches(180.5cm)5’1"11"
=83 inches(211 cm)6’ 11"
DimensionsIncluding LegPress(optional)
Length
Width =82inches(208.5cm)6’ 1(~)"
= 108inches (180.5 cm)9’
4

KEY
1
2
3
4
"PARTS LIST
PART# DESCRIPTION
70’309 FRONT LEG
7014202 LEG CABLE
3116201 3-1/2" PULLEY’
6467001 2" COVERCAP
3108102 QUICK DISCONNECTLiNK
I
1
1
2
1
KEY PART# DESCRIPTION QTY
6 3102501 3/8" WASHER 7
73102802 4
83102~24 1
9 3102904 3/8 X 3" BOLT 2
10 3102906 3/8 X 4" BOLT 2
3/8" LOCKNUT
3/8 X1-3/4" BOLT
NOTE:The LEGPRESSATTACHMENT(100) must be assembled ~efore connecting it to the
PARABODY220 GYMSYSTEMand can be attached to either side of the 220 GYMSYSTEM
FIGURE 1
STEP1:
¯ DISCARD!
Removethe LEGCABLEby removingthe bolts shownin FIGURE1. Discard the old LEGCABLEand the bolt holding the CABLE
to the base. 5

FIGURE2
STEP2:
¯ Slide two2" COVERCAPS(4) over the FRONTLEG(1) as shownin FIGURE
¯ SECURELYassemblethe FRONTLEG(1) to the 220 GymSystemusing two3/8 X4" BOLTS(10), one previougly removed
3/8" WASHEtLthree 3/8" WASHERS(6), one previously removed3/8" LOCKNUTand one 3/8" LOCKNUT(7) as shown
FIGURE2.
I1/2 11/2 I1/2 I1/2 I1/2 I 1/2 I
6
4, I I I I
3I I 1 I
2I I I I 1I I I I 6

;TEP3:
¯ Assemblethe new LEGCABLE(2) using the pre~5ously removedbolts as shownin FIGURE3. (NOTE:Makesure the
CABLEis runningin the grooves of all pulleys and abovethe retaining bolts.)

3/8 X
STEP4:
o SECURELYassemble one 3-1/2" PULLEY(3) to the FRONTLEG(1) using one 3/8 X1-3/4" BOLt"(8) and one 3/8" LOCK
(7). See FIGURE
[ 1/2 I~/~ [ 1/2 Il/’Z [~/~ [ ~]
6
45[ I _1
0 1 [ I I I .....
I I [ I I I8

3/8 X3"i
SECURELYattach the 100 LEGPRESSlo the FRONTLEG(1) using two 3/8" X 3" BOLTS(9), four 3/8" WASHERS(6),
two 3/8" LOCKNUTS(7). See FIGURE
¯Route LEGCABLE(2) around the 3-1/2" PULLEYon the LEGPRESSas shownin FIGbqtE5. (NOTE:Pulley mayneed to
temporarily removed.)
¯Attach the end of the LEGCABLE(2) to the QUICKDISCONNECTLINK(5). See FIGURE
¯SECURELYtighten the QUICKDISCONNECT(5) to the tab on the FRONTLEG(1) as shown in FIGURE

FIGURE 6
STEP6:
¯The100 LEGPRESSis equippedwith a spring pin adjustment to accommodatedifferent sized users and allow easy. entry andexit
fromthe machine.Touse, youmustslightly pushagainst the foot plates to take tension off the pin.
¯ Before setting the correct amountof tension in the cables; push the HEADPLATEdown,insert the WEIGHTSELECTORPIN,
and performseveral repetitions at the leg press station. This will relax the cable systemandprevent the ttEADPLATEfrom
lifting up.
¯ If CABLEADJUSTMENTis needed, adjust the 100 LEGPRESSinto the last adjustment hole (so the LEGPRESSis spread out)
and reference the 220 GYMSYSTEMassembly instructions.
THIS CONCLUDESTHE ASSEMBLY OF THE 221 LEG PRESS ADAPTER KIT
Thankyoufor purchasingthe Parabody221LegPress AdapterKit. If unsureof properu~eof equipment,call
yourlocal Parabodydistributor or call the Parabodycustomerservice departmentat (81t0) 328..9714.
10