ParaBody 870 User manual

1
870 VERTICAL DUMBBELL RACK
CLASSH
PART # 7081401
REV.A Revision: 03/26/01
USER’S GUIDE
WARNING:
Read and follow all directions
for each step to insure proper
assembly of this product.
Version: 870107

THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF
EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES!
1. Before using, read all the warnings and instructions
on the use of this machine. Use only for intended
exercise. DO NOT modify the machine.
2. Obtain a medical exam before beginning any
exercise program.
3. Keep body and clothing free of all moving objects.
4. Inspect the machine before use. DO NOT use it if it
appears damaged. DO NOT attempt to fix a broken or
j
ammed machine. Notify your authorized ParaBody
dealer before use and have repairs made by an
authorized service technician.
5. Be certain that weight pin is completely inserted.
Use only the pin provided by the manufacturer. If
unsure, call your authorized ParaBody dealer.
6. Never pin the weights or prop plate into an elevated
position. DO NOT use the machine if found in this
condition. DO NOT attempt to fix. Notify your
authorized ParaBody dealer.
7. Inspect cables and their connections before using
machine. Pay particular attention to the cable ends.
DO NOT attempt to fix. Notify your authorized
ParaBody dealer before use and have repairs made by
an authorized service technician.
8. Make sure all spring loaded pull pins are fully
engaged in the adjustment position and fully tighten
thumbscrew before use.
9. Children must not be allowed near this machine.
Supervise teenagers.
.
IMPORTANT SAFETY INFORMATION
TABLE OF CONTENTS
Safety Statement.............2
General Notes..................3
Tools Required................3
Parts List.........................4
NOTE: In a continual effort to improve our products, specifications are subject to change
2001 Life Fitness, a division of Brunswick Corporation. All rights reserved.
ParaBody is a trademark of Brunswick Corporation
www.parabody.com
2
Assembly Instructions.....4
General Maintenance.......5
Warranty Statement..........6
Product Services..............7
Insert-Registration Card
©

IMPORTANT NOTES
Please note:
Tools Required forAssembly
* Thank you for purchasing the ParaBody 870 DUMBBELL RACK. Please read these
instructions thoroughly and keep them for future reference. This product must be assembled
on a flat, level surface to assure its proper function.
* 3/4” inch socket
* 9/16” inch socket
*Adjustable wrench
* Rubber mallet or hammer
3
NOTE:BOLTLENGTHISMEASUREDFROMTHEUNDERSIDEOFTHEHEADOFTHE BOLT.
BOLT LENGTH RULER:
* This product must be assembled on a flat, level surface to assure its proper function. DO NOT
securely tighten any frame connections until the entire frame has been assembled, unless
otherwise stated.
Bolt Length Ruler
0123456
1/2 1/2 1/2 1/2 1/2 1/2
BOLT LENGTH

4
PARTS LIST
0123456
1/2 1/2 1/2 1/2 1/2 1/2
PART #
6215708
6284702
6013708
3102942
3102501
3102802
KEY
1
2
3
4
5
6
QTY
1
1
1
2
4
2
PART #
6011401
6405201
6236701
6177001
DESCRIPTION
SAFETYLOCK PIN
2” SQ. END CAP
1-3/4” SQ. END CAP
2-1/2 X 5-1/2” NON SKID STRIP
QTY
1
1
1
4
DESCRIPTION
FOOT BRACE ASSY
ADJUSTABLE TUBEASSY
CONNECTOR PLATE
3/8 X 3-1/2” BOLT
3/8” FLATWASHER
3/8” LOCK NUT
KEY
7
8
9
10
STEP5:
FIGURE 5
• Remove the hardware from the FRONT LEG of BENCH assembly
• Insert one 1-3/4 END CAP(9) into the open end of theADJUSTABLE TUBEASSEMBLY (2) as shown
• Assemble theADJUSTABLE TUBEASSEMBLY(2) and the CONNECTOR PLATE (3) to the BENCH using
two 3/8 X 3-1/2” BOLTS (4), four 3/8” FLAT WASHERS (5) and two 3/8” LOCK NUTS (6).
(NOTE: THE BRACKET ONTHEADJUSTABLE TUBEASSEMBLYIS FLUSH (EVEN) WITHTHE
TUBE,ASSEMBLEFLUSH SIDE UP)
• Insert one 2” SQ END CAP (8) into the front end of the FOOT BRACE (1) as shown
• Attach four NON SKID STRIPS (10) to the FOOTBRACE (1)
• Slide the FOOT BRACE (1) over theADJUSTABLE TUBEASSEMBLY(2) to the desired hole setting and
hold in place with the SAFETY LOCK PIN (7)
3
6
1
8
2
4
10
9
5
7
FRONT
BENCH
FRAME