ParaBody 661101 User manual

661101 LEG PRESSADAPTER KIT
Part #7049801
Rev. B Revision: 07/19/011
ASSEMBLY INSTRUCTIONS

IMPORTANT NOTES
Please note:
Tools Required forAssembly
* Thank you for purchasing the 661101 Leg PressAdapter Kit. Please read these
instructions thoroughly and keep them for future reference. This product must be assembled
on a flat, level surface to assure its proper function.
* Rubber mallet or hammer
* 3/4” wrench
* 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* 7/32” Allen wrench
* Adjustable wrench
* Tape measure
2
NOTE:BOLTLENGTHISMEASURED FROMTHEUNDERSIDEOFTHEHEAD OFTHEBOLT.
BOLT LENGTH RULER:
* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased from your Parabody customer service representative
at [phone].
Bolt Length Ruler
0123456
1/2 1/2 1/2 1/2 1/2 1/2
BOLT LENGTH
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
2. Do not allow minors or children to play on or around this equipment.
1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
3. Exercise with care to avoid injury.
4. If unsure of proper use of equipment, call your local Parabody distributor or call the
Parabody customer service department at [phone].

STEP 1
FIGURE 1
PART #
6747708
3116201
3108102
6427101
3118701
3201501
6271801
6747901
KEY
1
2
3
4
5
6
7
8
QTY
1
2
1
1
1
1
1
1
PART #
3102701
3102501
3102802
3102502
3102801
3102902
3102910
3102909
DESCRIPTION
3/8”HEXNUT
3/8”WASHER
3/8”LOCKNUT
1/2”WASHER
1/2”LOCKNUT
3/8X2-1/4”BOLT
1/2X3”BOLT
3/8X1”
QTY
2
3
2
4
4
2
4
1
DESCRIPTION
FRONTLEG
3-1/2”PULLEY
QUICKDISCONNECTLINK
KEYHOLECLEVIS
2”PULLEY
SWIVELSNAP
72”ELASTICCORD
LEGPRESSCABLE
KEY
9
10
11
12
13
14
15
16
NOTE: The LEG PRESS ATTACHTMENT (100101) must be assembled before connecting it to the
PARABODY 660101 HOME GYM
PARTS LIST
• REMOVE the four 3/8” X 1” BUTTON HEAD CAP SCREWS from the rear SHROUD. Remove the SHROUD from the 660101
HOME GYM. See FIGURE 1.
REAR SHROUD
3/8” X 1” BUTTON
HEAD CAP SCREW
3
3/8” X 1” BUTTON
HEAD CAP SCREW

STEP 2
FIGURE 2
4
REAR
SHROUD
• If the 663101 SECOND STACK OPTION is not installed, the rear SHROUD opening must be removed. Apply pressure to the
bottom of the SHROUD where the “V” groove is and carefuly remove the weight stack opening on the SHROUD as shown in
FIGURE 2.
0123456
1/2 1/2 1/2 1/2 1/2 1/2

FIGURE 3
STEP3
• Remove two 3/8” LOCK NUTS, two 3/8” HEX NUTS, two SWIVEL SNAP (keep elastic cords attached), two 3/
8 X 1/2” SPACERS, and one 3/8”THREADED SHAFT from the bracket on the BASE as shown in FIGURE 3.
BASE
5
HEXNUT
• Discard the two 3/8 X 1/2” SPACERS.
HEXNUT
3/8 X 1/2”
SPACERS
(DISCARD)
3/8”THREADED SHAFT
SWIVELSNAP
3/8”LOCKNUT
SWIVELSNAP
3/8”LOCKNUT
ELASTICCORD

6
FIGURE 4
BASE
HEXNUT 3/8” LOCK NUT
2
STEP4
• Assemble the two previously removed 3/8” HEX NUTS, two previously removed SWIVEL SNAPS, one 3-1/2” PULLEY (2), and two
previouslyremoved 3/8” LOCK NUTSto the previously removed3/8”THREADED SHAFT as showninFIGURE 4.
HEXNUT
3/8”LOCK NUT
0123456
1/2 1/2 1/2 1/2 1/2 1/2
3/8”THREADED SHAFT
SWIVELSNAP
SWIVELSNAP
FIGURE 5
STEP5
• Removeone3/8X 2” BOLT,two3/8”WASHERS, one 2-7/8” L-BRACKET, one 4-1/2” PULLEY,andone 3/8” LOCK NUT from the
upper flat on the BASE as shown in FIGURE 5.
BASE
3/8”WASHER
4-1/2” PULLEY
3/8”WASHER
3/8”LOCK NUT
2-7/8”L-BRACKET
3/8”X2”BOLT

FIGURE 7A
(WITHOUT 663101
SECOND STACK
OPTION)
STEP 7A
3/8”LOCK NUT
TOPBOOM
9 3/8”HEX NUT
• SECURELY assembleone 2” PULLEY(5) tothe 3/8”THREADEDSHAFTontheTOPBOOMusing one previously installed3/8”
WASHER, one 3/8”HEXNUT (9)andone previously installed 3/8”LOCKNUTas shown inFIGURE 7A.
5
3/8”WASHER
FIGURE 6
STEP6
• SECURELY assemble thepreviouslyremoved 4-1/2” PULLEYtotheBASE using one 3/8X2-1/4”BOLT(14), two previously
removed3/8”WASHERS,one previously removed 2-7/8”L-BRACKET, oneSWIVELSNAP(6), one 3/8” HEX NUT(9), and one
previouslyremoved3/8”LOCKNUT.SeeFIGURE6.
BASE
14 3/8X2-1/4”
3/8”WASHER
4-1/2” PULLEY
2-7/8”L-BRACKET
6
9 HEXNUT
3/8”LOCK NUT
• If the 663101 SECOND STACK OPTION is installed follow STEP 7B .
3/8”WASHER
• Remove one 3/8” WASHER and one 3/8” LOCK NUT from the 3/8”THREADED SHAFT on theTOPBOOM.
7

FIGURE 7B (WITH
663101 SECOND
STACK OPTION)
STEP 7B
• If the 663101 SECOND STACK OPTION is NOT installed proceed to STEP 8 .
TOPBOOM
3/8” X 1” 16
10
5 11 3/8”LOCKNUT
• SECURELYassemble one 3/8 X 1” BOLT(16), one 3/8”WASHER(10),one2” PULLEY(5) and one 3/8” LOCK NUT(11) to the
bracket on the TOP BOOM as shown in FIGURE 7B.
STEP8
• SECURELY attach one 3-1/2” PULLEY(2) to the FRONT
LEG(1)using one 3/8X2-1/4”BOLT(14), two 3/8”WASH-
ERS(10),and one3/8”LOCKNUT(11). See FIGURE8.
• Attach the open end of PRESS LINK CABLE (8) to the
QUICKDISCONNECTLINK(3).SeeFIGURE8.
• SECURELY tighten the QUICK DISCONNECT(3) to the
tabon the FRONT LEG (1) asshowninFIGURE 8.
FIGURE 8
2
3/8X2-1/4” 14
SECURELY
TIGHTEN!
8
10
10 11
1
3
8
0123456
1/2 1/2 1/2 1/2 1/2 1/2

9
STEP9
FIGURE 9
• RouteLEGPRESS CABLE (8)aroundthe3-1/2”PULLEYon the LEGPRESSandUNDERthe3-1/2”PULLEYon the FRONTLEG(1)
asshown in FIGURE 9.
• SECURELYattach the LEG PRESS tothe FRONTLEG (1) using two 1/2” X 3”BOLTS (15), two 1/2” WASHERS (12), andtwo 1/2”
LOCKNUTS(13).SeeFIGURE9.
LEGPRESS
1/2X 3” 15
13
12 8
1

10
FIGURE 10
STEP10
• SECURELYattach the FRONT LEG (1) to 660 BASE using two 1/2 X 3” BOLTS (15), two 1/2” WASHERS (12) and two 1/2” LOCK
NUTS (13). See FIGURE 10.
• RouteLEGPRESSCABLE(8)underthe3-1/2” PULLEY on the 425 BASE as shown in FIGURE 10.
8
13 12
1
1/2 X 3” 15
BASE
0123456
1/2 1/2 1/2 1/2 1/2 1/2