Paradox Magellan MG32LRF Service manual

MG32LRF - User’s Quick Reference Guide
KEYPAD OVERVIEW
Partition 1 Status Partition 2 Status
MG32LRF Keypad
To Regular Arm:
1. Close all zones in the desired partition.
2. Press [ARM].
3. Enter your [ACCESS CODE].
To Stay Arm:
1. Press the [STAY]key.
2. Enter your [ACCESS CODE]*.
To Sleep Arm:
1. Press the [SLEEP]key.
2. Enter your [ACCESS CODE]*.
* If needed, press button(s) corresponding to desired partition(s). For two partitions, press the other key after the confirmation beep.
ARMING AND DISARMING
TO ARM
WHEN LEAVING... TO ARM
WHEN STAYING...
To Disarm:
[OFF] +[ACCESS CODE]*
Off Light (red)
On = Disarmed
Off = System armed
Power and Rx/Tx Light
On = Power on
Off = Power off
Fast Flash = Transmission/
reception in progress
Slow Flash = AC loss on keypad
StayD (grn)
On = StayD mode enabled
Slow Flash = Low battery on keypad
= Press once + [MASTER
CODE]for Quick Menu
Programming)
Zone Display:
The numbers [1] to [32] correspond
to zones 1 to 32 respectively. Open
or entry delay zones are illuminated,
and flash in alarm.
Arm (red), Sleep (yel), Stay (grn):
On = Partition armed
Off = Partition disarmed
Flash = Exit Delay
Fast Flash* = Exit Delay (final 10
sec.)
Fast Flash* = Partition in alarm
*Audible Indicators:
Continuous beep = Alarm,
Variable beep = Fire alarm
Intermittent beep = Beginning of exit delay
Fast beep = Final 10 sec. of exit delay
[TBL] Trouble display
ON = Trouble(s) occurring
[MEM] Alarm memory display
ON = Alarm(s) occurred
[BYP] Bypass programming
ON = Zone(s) bypassed
lnfo Key
Refresh display to see all open
zones.
MG32LRF_EQ01.fm Page 1 Friday, February 9, 2007 8:23 AM

Bypassed zones remained unarmed when the
partition is armed.
1. Press the [BYP] key.
2. Enter your [ACCESS CODE]*.
3. The corresponding LED of all open
zones will illuminate. Select the zone(s)
you want to bypass by entering the two-
digit zone number (i.e. zone 3 = 03). The
corresponding zone LED will flash.
4. Press the [ENTER]key to save and exit.
BYPASS PROGRAMMING
paradox.com
Printed in Canada 02/2007 MG32LRF-EQ01
To send a silent or audible alarm to your
Security Company, press and hold one of the
button combinations listed for 3 seconds.
When a trouble condition occurs, the [TBL]key
will illuminate.
1. Press the [TBL] key. The key will flash
and number(s) corresponding to the
trouble(s) will illuminate.
2. Read the corresponding explanation of
the trouble from the trouble list in the
MG5000 User Guide. If no repair
instructions are given, call your security
company for repairs.
3. Press the [CLEAR]key to exit.
\
To view the alarms that occurred during the
last armed period:
1. Disarm the system.
2. Press the [MEM] key.
3. The corresponding zone numbers that
were in alarm the last time the system
was armed will illuminate.
4. Press the [CLEAR]key to exit.
To mute the keypad:
Press and hold the [CLEAR]key for 6
seconds to enable or disable Keypad
Muting.
To modify the backlight:
1. Press and hold the [S]key for 3 sec-
onds.
2. The [MEM]key will illuminate.
3. Press the [S]key to set the desired
backlight level.
4. Press [CLEAR] or [ENTER]to exit.
PANIC ALARMS
Panic Alarm Type Button Combinations
Police
Medical
Fire
Press [1] & [3]
Press [4] & [6]
Press [7] & [9]
TROUBLE DISPLAY
ALARM MEMORY DISPLAY
KEYPAD SETTINGS
© Paradox Security Systems Ltd., 2005-2007. Magellan
is a trademark or registered trademark of Paradox
Security Systems Ltd. and its affiliates in Canada, the
United States and/or other countries. All rights reserved.
MG32LRF_EQ01.fm Page 2 Friday, February 9, 2007 8:23 AM