Paramount Fitness PH-S-112-GY User manual

Questions, problems, missing parts?
(8 ) – Friday a.m. – p.m., ST
c @
DANGER
DANGER
DANGER
WARNING
WARNING
WARNING
ATTACH YOUR
RECEIPT HERE
, PH-S-112-GY
WARNING
+
_
Electronic ignition.
Requires (1) AAA.
(Not Included)

BEFORE YOU BEGIN
TABLE OF CONTENTS
Before You Begin Page 2
BEFORE YOU BEGIN
(8 ) Monday – Friday
a.m. – p.m., ST, c
Safety Information Page
Package Contents Page
Hardware Contents Page
Assembly Page -
Operating Instructions Page -1
Care and Maintenance Page 1
Page 1
gnitoohselbuorrTT oubleshooting
Page 3
Page 1

WARNING

SAFETY INFORMATION
DANGER
r
l
t
f
WARNING
CAUTION
M
CAUTION
WARNING
WARNING
o
r
c
c
DANGER
o
k
WARNING
WARNING:
FOR OUTDOOR USE ONLY
CARBON MONOXIDE HAZARD

PACKAGE CONTENTS
PART DESCRIPTION QUANTITY
packed in inner carton
packed under Base
packed in 1 inner carton
attached to Head Assembly
packed in inner carton
packed in 1 inner carton
packed in inner carton
(secures LPG cylinder) packed with post supports
A
B
D
EF
G
H
J*
K
L
I
*Some models come with an optional sandbox feature. See page 5 for details on sandbox assembly.
AA
Bolt
Qty: 6
(Step 3)
BB
Bolt
Qty: 5
(Step 1 & 2)
CC
Bolt w/Lock Washer
Qty: 4
(pre-assembled with burner)
(Step 7)
DD
Screw
Qty: 4
(pre-assembled in
base/sandbox)
EE
Screw
Qty: 12
(Step 8)
FF
Flat Washer
Qty: 9
(Step 6 & 9)
HH
Nut
Qty: 4
(pre-assembled in
base/sandbox)
II
Cap Nut
Qty: 12
(Step 8)
GG
Flange Nut (GG)
Qty: 6
(Step 3)
HARDWARE CONTENTS
C
JJ
Wing Nut
Qty: 3
(Step 9)
LL
Wrench (LL)
Qty: 1
KK
,g×gU¿³½-¿Å_
Qty : 3
(Step 6)

ASSEMBLY
*Optional Sandbox: For models that come with a sandbox, the
remove the 4 Screws (DD) and Nuts (HH) that secure the
base to the sandbox. Pull open the plastic cap on top of the
plastic cap. Slide Base back over the sandbox and align the
holes in the base with the holes in the sandbox. Insert Screws (DD)
through the holes in the base and secure by tightening Nuts (HH)
sandbox prior to attaching wheels.
1Wheel Assembly KBase J Wheel Assembly Base
Bolts (BB) r
Wheel Assembly Base J
Wrench (LL)
Hardware Used:
2Post Supports IBase J Post Support
Base Bolt (BB)
Base Post
Supports Wrench
Hardware Used:
Plastic Cap
Sandbox
Base
PREPARATION
ESTIMATED ASSEMBLY TIME:
Tools Required for Assembly (NOT included):
2 x Bolts (BB)
Wrench (LL)
3 x Bolts (BB)
5

ASSEMBLY
3Lower Post GPost Supports I Post Supports I
Base JLower Post G
Post Supports Bolt (AA)
Post Supports and insert a Flange Nut (GG)
Post Support
Wrench
Hardware Used:
4Upper Post FLower Post G
5Tank Housing DUpper/Lower Posts F G Post Supports I
Tank Housing Base J
6Head
Assembly C
Washer Head Assembly C
Hardware Used:
6 x Bolt (AA)
6 x Flange Nut (GG)
(KK)
ÿҿ,gÛgUÁµ¿-ÁÉ_¿£¤
3 x Flat Washer (FF)
Flat

ASSEMBLY
7Head Assembly CUpper Post F Gas Hose EUpper/lower Posts F G
Hardware Used:
8NOTE: MAKE SURE TO REMOVE PROTECTIVE PLASTIC COVER ON REFLECTOR PIECES
PRIOR TO ASSEMBLY!
Ass
sections, loosen each screw prior to further assembly and
retighten after sections are aligned.
AScrew (EE)
Cap Nut (II)
A
B
Panels AScrew (EE) Cap Nut (II)
Screws (EE) Cap Nuts (II)
Hardware Used:
Head Assembly C
Upper Post FBolts with
Lock Washer (CC)
Wrench (LL)
Wrench (LL).
Ç¿Ò¿-UµgÑ¿£¤
12 Cap Nut (II)

ASSEMBLY
9Head Assembly C
3 Flat Washers (FF)
Flat Washers (FF)
Wing Nuts (JJ)
Wing Nuts (JJ)
Hardware Used: 6 x Flat Washer (FF)
10 only Tank Housing D
Post Supports IRegulator
HGas Hose ERegulator
Chain LTank Housing
NOTE: Use this heater only with a propane vapo r withdrawal
supply system. See chapter 5 of the standard for storage and
3 x Wing Nut (JJ)

OPERATING INSTRUCTIONS
r