Paramount Fitness PH-T-107-SS User manual

Questions, problems, missing parts?
(8 ) – Friday a.m. – p.m., T
c @
FOR YOUR SAFETY:
If you smell gas:
1. Shut off gas to the appliance.
3. If odor continues, keep away from the
appliance and immediately call your gas
DANGER indicates an imminently
hazardous situation which, if not avoided,
will result in death or serious injury.
Failure to comply with the precautions
and instructions provided with this heater
can result in death, serious bodily injury
and property loss or damage from hazards
and/or carbon monoxide poisoning. Only
persons who can understand and follow
the instructions should use or service
this heater.
Do not store or use gasoline or other
vicinity of this or any other appliance.
An LP-cylinder not connected for use
shall not be stored in the vicinity of this
or any other appliance.
Improper installation, adjustment,
alteration, service or maintenance can
cause property damage, injury or death.
Read the installation, operation and
maintenance instructions thoroughly
before installing or servicing this
equipment.
FOR OUTDOOR USE ONLY!
Keep a copy of your proof of
which will be needed if you
need to contact us about
warranty coverage.
Serial No.
Purchase Date
, or email us
.
Model Number: 60262/61322/62969
Item Number: PH-T-107-SS / PH-T-107-MK

BEFORE YOU BEGIN
BEFORE YOU BEGIN
(8 ) Monday – Friday
a.m. – p.m., ST, c

SAFETY INFORMATION
DANGER
r
l
t
f
WARNING
CAUTION
M
CAUTION
WARNING
WARNING
o
r
c
c
DANGER
o
k
WARNING
WARNING:
FOR OUTDOOR USE ONLY
CARBON MONOXIDE HAZARD
3

PART DESCRIPTION QTY
4
4
4
4
4
420
Hardware
Package List QTY
3
Wing Nut
6mm Washer
M5x25 Bolt
M5x8 Bolt
M5 Nut
60mm
M5x8 SS Bolt
Stud
Wrench
M5X12 Bolt 1
3
4
4
5
3
4
1
M4 self tapping screw
M5x8mm Bolt
M5X12mm Bolt
M5 Nut
M5X8 SS Bolt
PACKAGE CONTENTS

Before beginning assembly of this appliance, make sure all parts are present.
Compare all parts with package contents list and hardware contents as listed on the previous page. If any part is
missing or damaged, do not attempt to assemble this product. Contact customer service for replacement parts.
Phillips screwdriver w/medium blade Slip joint/adjustable pliers Adjustable wrench (2)
Remove all parts of the heater from the
packaging. ( Plastic ring on tank
housing should already be in place but if not,
slide the plastic ring over the bottom of tank
housing.)
STEP 3
Place the Burner on the Tank Housing,
then join them using 4 M5x8 Bolts.
STEP 4
Fix the Regulator to the Tank Housing
using a M5x12mm Bolt and M5 Nut.
STEP 1
STEP 2
1¸g¿w¿uÒÇu¿Á¸¿Á¿ÚÒ¿Ág¿Á>¿ɸy¿
to the base and cast iron weight( Note:
weight is preassembled to base),then
fasten with 4 M5 nuts from the inside of
the tank housing.
Use Wrench to tighten the bolts and nuts
as shown above.
PACKAGE CONTENTS

STEP 5
Connect 60mm Stud into each of the 3
holes at the top of the Emitter Screen,
STEP 6
Place the Emitter Screen on the Burner. Use 4
to connect the Emitter Screen
to the Burner. Tighten the Bolts.
STEP 7
Lower the Guard over the Emitter Screen
and insert the feet of the Guard into the
holes near the edge of the Burner.
STEP 8
Place a Washer on each of the 3 Studs.
M5x8 SS Bolts
ASSEMBLY

ASSEMBLY

OPERATING INSTRUCTIONS : SAFETY FIRST

1. Make 2-3 oz. of leak test solution
detergent and three parts water).
2. Apply several drops of solution
where hose attaches to regulator.
3. Apply several drops of solution
where regulator connects to cylinder.
4. Make sure all patio heater valves are OFF.
5. Turn cylinder valve ON.
Turn cylinder valve OFF.
If leak is detected at hose/regulator connection, tighten connection and
perform another leak test. If bubbles continue to appear, call customer
service at [email protected] or [phone], Monday to Friday,
7:30 a.m.-4:00p.m. PT
If leak is detected at regulator/cylinder valve connection, disconnect,
reconnect, and perform another leak test. If you continue to see bubbles
after several attempts, cylinder valve is defective. Contact customer service
Note: Whenever gas connections are loosened or removed, you must perform a
complete leak test.
Perform all leak tests outdoors.
NEVER leak test when smoking
Do not use heater until all connections
have been leak tested and show no signs
of leakage.
Your heater was designed and
approved for
. Do NOT use it inside a
building, garage, or any other
enclosed area.
Make sure surrounding areas are
free of combustible materials,
Ensure that there is no
obstruction to air ventilation. Be
sure all gas connections are tight
and there are no leaks.
Be sure the cylinder is clear of
debris. Be sure any component
removed during assembly or
servicing is replaced and
fastened prior to starting.
Heater should be thoroughly
inspected before each use, and
at
least annually. If re-lighting a
hot heater, always wait at least
5 minutes.
Inspect the hose assembly for
evidence of excessive abrasion,
cuts, or wear. Suspected areas
should be leak tested. If the
hose leaks, it must be replaced
prior to operation. Only use the
replacement hose assembly
OPERATING INSTRUCTIONS
valve is defective. Email us at [email protected] or [phone],
Monday to Friday, 7:30 a.m.-4:00p.m. PT

FOR YOUR SAFETY
Heater will be hot after use. Handle with
extreme care.
For a safe and heating experience, perform this check
before each use:
I am familiar with entire owner’s manual and understand all
precautions noted.
All components are properly assembled, intact and operable.
No alterations have been made.
All gas connections are secure and do not leak.
Wind velocity is below 10 mph.
Heater is for use outdoors (outside any enclosure).
Heater is away from windows, air intake openings, sprinklers and
other water sources.
Heater is at least in. on top and at least 24 in. on sides from
combustible materials.
Heater is on a hard and level surface.
All burner passages are clear.
All air circulation passages are clear.
Clothing or other protective material should not be hung from the
heater, or placed on or near the heater.
Any guard or other protective device removed for servicing the heater
must be replaced prior to operating the heater.
The heater should be inspected before each use and at least annually
surface
temperatures and should stay away to avoid burns or clothing
ignition.
area of the heater.
imperative that control compartment burner and circulating air
passageways of the heater be kept clean and free of debris and/or
spider or insect nests.
Turn control knob
clockwise to OFF while
depressing the knob.
(urner make a slight
popping noise when
extinguished).
isconnect
when heater is not in use.
NOTE: After use, some
discoloration of the
emitter screen is normal.
1. Gas control knob is in
OFF position.
2. Gas tank valve is OFF.
3. Disconnect gas line.
4. Heater is stored upright
in a secure location.
OPERATING INSTRUCTIONS