PNI SafeHome PT225G User manual

PNI SafeHome PT225G
EN User manual ......................................................... 2
BG Ръководство за употреба ............................. 16
DE Benutzerhandbuch .............................................. 32
ES Manual de usuario ............................................... 48
FR Manuel utilisateur ............................................... 62
HU Használati utasítás .............................................. 78
IT Manuale utente .................................................. 92
NL Handleiding ........................................................ 106
PL Instrukcja obsługi ............................................... 120
RO Manual de utilizare ............................................. 134

3 - User manual
PNI SafeHome PT225G
Smart gas detector
User manual

3 - User manual 4 - User manual
PNI SafeHome PT225G is a gas detector
equipped with a high sensitivity semiconductor
sensor. In the event of a gas leak and the gas
concentration exceeds the preset limit, the
detector will trigger an audible and light alarm
and send a notification to the Tuya Smart
application.
A
B
C
D

3 - User manual 4 - User manual 5 - User manual
A - Gas inlet
B - Test Button
C - Reset button
Technical specifications
• Supply voltage: 230VAC
• Average consumption: ≤1.5W
• Alarm sound: 70dBm
• Detected gases: CH4 (methane gas),
LPG, natural gas
• Gas density alarm level: 6% LEL ± 3% LEL
• WiFi frequency: 2.4GHz
• Transmission power: 100mW
• Working temperature: -26°C ~ +80°C

4 - User manual 5 - User manual 6 - User manual
Installation
Before deciding where to install the detector,
determine if the detected gas is heavier or
lighter than air. If the gas is heavier than air (eg
LPG), install the detector 0.3-1m away from
the floor. If the gas is lighter than air (eg natural
gas, methane gas), install the detector 0.3-1m
away from the ceiling. The distance from the gas
source must be less than 1.5m.
Control from the Tuya Smart app
1. Download and install the Tuya Smart
application on your smart phone. Search for the

5 - User manual 6 - User manual 7 - User manual
app in the Google Play / App Store or scan the
QR code below:
Android iOS
2. After installation, open the application,
create an account and log in.
3. Enable WiFi (2.4GHz) and GPS Location on
your mobile phone.
4. To add the detector to the application, tap the
“+” icon in the upper right corner

6 - User manual 7 - User manual 8 - User manual
5. In the application select from the left menu
Sensors - Gas detector (WiFi)
6. Select the WiFi network you want to connect
to and add the network password.
7. Plug in the detector. The green LED will flash
quickly. If it does not flash quickly, press the
Reset key for about 5 seconds until the green
LED flashes quickly.
8. Tap Next and select Blink quickly.
9. Wait for the application to identify the
detector.
10. After identifying your detector, press the
Done button.
11. After pairing, the LED (test button) lights
green (monitoring state). In the event of an
alarm, the LED turns red.

7 - User manual 8 - User manual

9 - User manual 10 - User manual

9 - User manual 10 - User manual 11 - User manual
Detector testing
To test the alarm function, press the Test button
on the detector or in the application. The red
LED will flash and the built-in buzzer will sound.
Warning
If an alarm occurs, proceed as follows:
• Turn o the gas source immediately.
• Open windows or doors.
• Do not light bulbs or any source of fire or
sparks.

10 - User manual 11 - User manual 12 - User manual
Troubleshooting
After powering up the detector, the LED flashes
for a long time
• The detector has probably not been
powered on for a long time or you have
tried to test the detector during the sensor
priming period. Power on the detector and
wait for the sensor to fully prime.
The LED flashes and the audible alarm sounds
continuously.
• The sensor is defective. Call a specialist
service center.
Cannot add the detector to the application.
• Too far from the router. Move the detector
closer to the router (max. 10 m).

11 - User manual 12 - User manual 13 - User manual
• Check your WiFi network password.
Resume the procedure.
Warnings
• Do not use detergents to clean the
detector.
• Do not spray substances in front of the
detector.
• The lifespan of the semiconductor sensor
is up to 5 years. Replace the detector in a
timely manner.
• Is normal for the detector housing to heat
during the operation of the detector. This
does not indicate a fault.

12 - User manual 13 - User manual 14 - User manual
Simplified EU Declaration of Conformity
SC ONLINESHOP SRL declares that the
Smart gas detector PNI SafeHome PT225G
is in compliance with the EMC Directive
2014/30/EU and the RED Directive 2014/53
/ EU. The full text of the EU Declaration of
Conformity is available at the following internet
address:
https://www.mypni.eu/products/8597/
download/certifications
CERTIFICATE OF QUALITY AND
COMMERCIAL WARRANTY
The products identified in this certificate on
the basis of the trade name and the unique
serial number S / N, benefit from a commercial

13 - User manual 14 - User manual 15 - User manual
guarantee as follows: The warranty period
for individuals is 24 months from the date of
delivery formanufacturingandmaterialdefects.
The warranty period for legal entities is
12 months from the date of delivery for
manufacturing and material defects.
The warranty period is calculated from the date
of invoicing of each product.
The average duration of use of the product is
48 months, provided that the installation and
operating instructions that accompany the
product are followed.
The commercial guarantee does not aect the
consumer’s rights provided by the applicable
legislation in force, respectively the Emergency
Ordinance 140 / 28.12.2021 on certain aspects

14 - User manual 15 - User manual
regarding the contracts of sale of goods,
OG 21/1992 on consumer protection with
subsequent amendments and completions and
Law 296/2004 on the Consumer Code as
subsequently amended and supplemented.
Download the warranty certificate:

17 - Ръководство за употреба
PNI SafeHome PT225G
Интелигентен газов детектор
Ръководство за употреба

17 - Ръководство за употреба 18 - Ръководство за употреба
PNI SafeHome PT225G е газов детектор,
оборудван с високочувствителен
полупроводников сензор. В случай на
изтичане на газ и концентрацията на газ
надвиши предварително зададената
граница, детекторът ще задейства звукова
и светлинна аларма и ще изпрати известие
до приложението Tuya Smart.
A
B
C
D

17 - Ръководство за употреба 18 - Ръководство за употреба 19 - Ръководство за употреба
A - Вход за газ
B - Бутон за тестване
C - Бутон за нулиране
Технически спецификации
• Захранващо напрежение: 230VAC
• Средна консумация: ≤1.5W
• Звук на аларма: 70dBm
• Открити газове: CH4 (газ метан), LPG,
природен газ
• Алармено ниво за плътност на газа: 6%
LEL ± 3% LEL
• WiFi честота: 2.4GHz
• Мощност на предаване: 100mW
• Работна температура: -26°C ~ +80°C

18 - Ръководство за употреба 19 - Ръководство за употреба 20 - Ръководство за употреба
Инсталация
Преди да решите къде да инсталирате
детектора, определете дали откритият
газ е по-тежък или по-лек от въздуха.
Ако газът е по-тежък от въздуха (напр.
LPG), монтирайте детектора на 0,3-1 m от
пода. Ако газът е по-лек от въздуха (напр.
природен газ, газ метан), монтирайте
детектора на 0,3-1 m разстояние от тавана.
Разстоянието от източника на газ трябва да
бъде по-малко от 1,5 m.

19 - Ръководство за употреба 20 - Ръководство за употреба 21 - Ръководство за употреба
Управление от приложението
Tuya Smart
1. Изтеглете и инсталирайте приложението
Tuya Smart на вашия смарт телефон.
Потърсете приложението в Google Play /
App Store или сканирайте QR кода по-долу:
Android iOS