Poly Blackwire 8225 User manual

Blackwire 8225
User Guide
PLANTRONICS + POLYCOM. NOW TOGETHER AS

Contents
Overview 3
Setup and software 4
Power and setup 4
Load software 4
Fit 5
Adjust the headband 5
Position the boom 5
Adjust the boom 5
Basics 6
Make/take/end calls 6
Volume 6
Mute 6
ANC 6
Online indicator 6
Troubleshooting 7
Troubleshoot 7
Support 8
2

Standard LEDs and functions
Icons Inline control LEDs What they mean
Call button Flashing green Incoming call
Solid green On a call
Slow flashing green Call on hold
Volume up button Increases the listening volume
Volume down button Decreases the listening volume
Mute button Solid red Headset muted
ANC Active Noise Canceling
Microsoft Teams LEDs and functions*
Icons Inline control LEDs What they mean
Call button Solid purple Headset connected; Microsoft Teams connected
Flashing purple x3 Microsoft Teams failed to connect
Flashing blue Incoming call
Solid blue On a call
Slow flashing blue Call on hold
Pulsing purple Microsoft Teams notification
Volume up button Increases the listening volume
Volume down button Decreases the listening volume
Mute button Solid red Headset muted
ANC Active Noise Canceling
NOTE * Requires Microsoft Teams variant and application
Overview
3

Power on your headset by connecting to your computer or mobile device.
•USB-A/USB-C connector
Download Poly Hub for Windows and Mac by visiting poly.com/software. This allows you to
customize your device behavior through advanced settings and options.
Setup and software
Power and setup
Load software
4

Lengthen or shorten the band until it fits comfortably. The cushions should sit comfortably over
the center of your ears.
This headset can be worn on the left or right side.
Rotate the boom to align with your mouth.
CAUTION To avoid breaking the boom, only rotate it up and over 180°.
Gently bend the boom in or out so it is approximately two finger widths from the corner of your
mouth.
Fit
Adjust the headband
Position the boom
Adjust the boom
5

Headset call control is a software feature and dependent on a compatible softphone. If you have
not installed Poly Hub (poly.com/software) or do not have a compatible softphone, press the
headset call button first and then make/take/end the call using the softphone application.
Answer or end a call
Tap the Call button or use your softphone.
Make a call
Dial using your softphone application.
Redial
When not on an active call, double-tap the call button to redial the last call.
Hold
To put a call on hold, press and hold the Call button until you hear a beep or voice prompt.
Listening volume
Press the Volume up (+) or Volume down (-) button.
Adjust headset microphone volume (softphone)
Place a test softphone call and adjust softphone volume and PC sound volume accordingly.
During a call, briefly press the mute button to mute the microphone on the inline controller. To
unmute press the button again.
Active Noise Cancelling (ANC) reduces external noise and enhances your music and sound quality.
Slide the ANC switch to choose:
• Mid: recommended for office
• High: recommended for loud environments
Your headset LEDs flash red to inform others that you are on a call. Manage settings in Poly Hub.
Basics
Make/take/end calls
Volume
Mute
ANC
Online indicator
6

I cannot hear caller. • Listening volume is too low. Press the volume up button on the
headset. and/or ensure that the volume setting on your computer
is set accurately.
• Your headset is not set as the default audio device. Use the audio
settings in your sound control panel/preferences to select your
headset as the default audio device.
Callers cannot hear me. • Headset is muted. Tap the mute button to unmute the
microphone.
• Headset microphone boom aligned incorrectly. Align the headset
boom with your mouth.
• Your headset is not set as the default Voice device. Use the audio
settings in your sound control panel/preferences to change the
input device.
The sound in the headset is
distorted.
I can hear an echo in the headset.
• Lower the listen volume on your softphone until the distortion
disappears.
• Adjust volume on headset.
When I use my headset with a
softphone, the headset call control
and mute buttons don't work.
• Make sure the softphone you are using is supported by viewing
www.plantronics.com/softphonecompatibility.
• If required to enable headset control (answer/end and mute)
functionality, ensure you have Plantronics Hub for Windows/Mac
installed. See Load software.
• Your mobile device may not support call control functionality.
Check with device manufacturer.
The other headset I was using to
listen to music does not work any
more.
• Your headset will set itself as the default audio device in Windows.
Use the audio settings in your sound control panel/preferences to
change the audio device.
My phone is not finding my headset
during a call or while listening to
music.
• When on a call or listening to music, make sure that audio is
routing to the desired headset by going to your settings and
ensuring it is defaulted.
Troubleshooting
Troubleshoot
7

Support
NEED MORE HELP?
poly.com/support
Plantronics, Inc. Plantronics B.V.
345 Encinal Street
Santa Cruz, CA 95060
United States
Scorpius 171
2132 LR Hoofddorp
Netherlands
©2020 Plantronics, Inc. All rights reserved. Poly, the propeller design, and the Poly logo are
trademarks of Plantronics, Inc. Bluetooth is a registered trademark of Bluetooth SIG, Inc. and any
use by Plantronics, Inc. is under license. All other trademarks are the property of their respective
owners. Manufactured by Plantronics, Inc.
217736-06 05.20
8