PR Lighting PR-2203 XR 200 User manual

XR 200（BEAM）
PR-2203
This product manual contains important information about the safe installation and use of this
projector. Please read and follow these instructions carefully and keep this manual in a safe place
for future reference.
PR LIGHTING LTD.
http://www.pr-lighting.com

2/20
INDEX
SAFE USAGE OF THE PROJECTOR 3
INSTALLING THE PROJECTOR 4
FITTING LAMP 4
POWER SUPPLY – MAINS 5
CONTROL CONNECTIONS 5
DMX TERMINATOR 6
SETUP OPTIONS-PROJECTOR CONFIGURATION 6
TO SET THE DMX START ADDRESS 6
STAND-ALONE MODE 7
MASTER/SLAVEMODE 7
OPERATION MENU 8
REPLACING GOBOS 10
DMX PROTOCOL 11
INDICATION OF LED DIGITAL TUBE 13
MAINTENANCE 13
LUBRICATION 13
KEEPING THE PROJECTOR CLEAN 13
TROUBLESHOOTING 14
TECHNICAL DATA 15
ELECTRICAL DIAGRAM 18
COMPONENT ORDER CODES 19
Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without
notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of
product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence
arising from them.
Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good
condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the
unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.
ACCESSORIES
These items are packed together with the projector:
Name Quantity Unit Remark
G clamps 2 Pcs
XLR cable 1 Pc with plug
Safety cord 2 Pcs
This manual 1 Pc
Ωclamps 2 Pcs Optional

When unp
a
Should the
r
The projec
t
excessive
h
The projec
t
The projec
t
The projec
t
that no ven
t
Do not proj
e
A
void direc
t
Do not atte
m
Electrical c
o
Before inst
a
It is essenti
a
Do not con
n
Make sure
with other c
a
Keep the l
a
The projec
t
attached a
s
The lamp
u
cooled, thi
s
lamp and t
h
Never run t
The lamp s
Shields an
d
impaired, f
o
Exterior su
r
There is n
o
covers rem
If you have
Always
d
before a
t
a
cking and be
f
r
e be any da
m
t
or is for ind
o
h
eat, humidity
t
or is not desi
g
t
or is only inte
n
t
or must be in
s
t
ilation slots a
r
e
ct the beam
t
exposure to
t
m
pt to disma
n
o
nnection mu
s
a
llation, ensu
re
a
l that each p
r
n
ect this devi
c
that the pow
e
a
bles. Only ha
n
a
mp clean. D
o
t
or should al
w
s
shown in “in
s
u
sed in this pr
o
s
will require a
h
e projector.
B
he projector
w
hall be chang
d
lens shall b
e
o
r example b
y
r
face tempera
o
user service
a
oved.
any question
s
d
isconnec
t
t
tempting
a
SAF
E
f
ore disposin
g
m
age caused
b
o
or use only,
I
and dust. Do
g
ned or inten
d
n
ded for insta
l
s
talled in a lo
c
r
e blocked.
onto inflamm
a
t
he light from
n
tle and/or m
o
s
t only be car
r
re
that the volt
a
r
ojector is cor
r
c
e to any othe
e
r-cord is nev
e
n
dle the powe
r
o
not touch th
e
w
ays be insta
l
s
talling the pr
o
o
jector is a di
s
pprox 15 min
u
B
ut occasional
w
ithout a lamp
ed if it has be
c
e
changed if
y
cracks or de
e
tures of the lu
a
ble parts insi
d
s
, don’t hesita
t
from the
a
ny maint
e
E
USAG
E
g
of the carto
n
b
y transportat
I
P20. Use o
n
not allow co
n
d
ed to be mou
l
lation, operat
i
c
ation with ad
e
a
ble surfaces,
the lamp. Th
e
o
dify the proje
c
r
ied out by qu
a
a
ge and freq
u
r
ectly earthed
r types of dim
e
r crimped or
r
-cord by the
p
e
lamp glass
w
l
led with a se
c
o
jector” sectio
n
s
charge lamp.
u
tes. Switchi
n
breaks will p
r
.
c
ome damag
e
they have b
e
e
p scratches.
minaire after
5
d
e the projec
t
te to consult
y
mains, w
h
e
nance wo
3/20
E
OF TH
E
n
check if ther
e
ion, consult y
o
n
ly in dry loc
a
n
tact with wat
e
nted directly
o
i
on and maint
e
e
quate ventila
t
minimum di
s
e
light is harm
f
c
tor in any wa
y
a
lified person
n
u
ency of pow
e
and that elec
t
mer apparatu
damaged by
p
lug. Never p
u
w
ith bare han
d
c
ondary safe
t
n
.
After switchi
n
n
g the lamp o
n
r
olong the life
o
e
d or thermall
y
e
come visibly
5
minutes op
e
t
or, do not op
e
y
our dealer or
h
en the d
e
rk !
E
PROJ
E
e
is no transp
o
o
ur dealer an
d
a
tions. Keep t
h
e
r or any othe
r
o
n to inflamm
a
e
nance by qu
t
ion, at least
5
s
tance is 12m.
f
ul to the eye.
y
.
n
el.
e
r supply mat
c
t
rical installati
o
s.
sharp edges
u
ll out the plu
g
d
.
t
y fixing. A sa
n
g off don’t att
e
n
and off at s
h
o
f the lamp a
n
y
deformed o
r
damaged to
s
e
ration is 35℃
e
n the housin
g
manufacture
r
e
vice is no
t
E
CTO
R
o
rtation dama
g
d
do not use t
h
h
is device a
w
r
liquids.
a
ble surfaces.
alified person
n
5
0cm from adj
12m
c
h the power r
e
o
n conforms t
o
. Never let th
e
g
by tugging t
h
fety cord is s
u
e
mpt to resta
r
h
ort intervals
w
n
d projector.
r
reached its li
s
uch an exte
n
, when stead
y
g
and never
o
r
.
t
in use o
r
g
e before usi
n
h
e apparatus.
w
ay from rain
n
el.
acent wall su
r
e
quirements
o
o
all relevant
s
e
power-cord c
o
h
e power-cor
d
u
pplied for th
i
r
t the projecto
r
w
ill reduce the
fe limi
t
.
n
t than their
e
y
state is achi
e
o
perate the pr
o
r
before cl
e
n
g the project
o
and moistur
e
r
faces. Be su
r
o
f the project
o
s
tandards.
o
me into conta
c
d
.
i
s; it should b
r
until lamp h
a
life of both th
e
ffectiveness
i
e
ved 45℃,
o
jector with th
e
aning it
o
o
r.
e
,
r
e
o
r.
c
t
e
a
s
e
i
s
e
o
r

4/20
INSTALL THE PROJECTOR
Take 2 clamps and 1 safety cords out from the package and mount 2 clamps on the underside of fixture with 4 retainers
attached to each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the
WARNING on the underside of the base as shown above) Always ensure that the projector is firmly anchored to avoid
vibration and slipping whilst functioning. Always ensure that the structure that you are going to mount the projector is
secure and is strong enough to support the weight of the fixture.
WARNING
1. The projector MUST be lifted or carried by the HANDLES instead of clamps.
2. For safety the safety cord should support 10 times of the unit’s weight.
FITTING THE LAMP
Unplug the projector from power before lamp
installation or replacement and wait for it to
cool.
Lock the yoke before fitting/replacing the lamp.
Loosen 8 fast-fit screws and remove the back
cover,
you can see the structure as shown in the figure
2..
After unplug the power wires, hold the end of
the lamp and push it as directed by the arrow
resulting in the other end of the lamp
unblocked ,then pull the lamp out. Before
installing new lamp, plug the power wires for the
lamp tightly. Installation of the lamp is an reverse
sequence to the pull-out.
Fit new lamp and close the back cover by fastening 8 fast-fit screws. Note: don’t touch the bulb of the new lamp with
bare hand so as not to influence the beam output; Do not harm the sticking out point of the lamp during its installation.
WARNING: Care should always be taken when handling these lamps. Always read the manufacturers
"Instructions for use" enclosed with the lamp.
CONTROL
PANEL
CLAMP
HANDLE
SAFETY CORD
106
106
WARNING
To pass 1 SAFETY CORD
through 2 holes for safety
FAST-FIT SCREWS
LAMP
AB

5/20
POWER SUPPLY-MAINS
Connect the power cord as follows:
L (live) =brown
E (earth) =yellow/green
N (neutral) =blue
Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked
on the panel of the projector. It is recommended that each projector be supplied separately so that they may be
individually switched on and off.
IMPORTANT
It is essential that each projector is correctly earthed(yellow/green twin wire) and the electrical installation
conforms to all relevant standards.
CONTROL CONNECTION
Connection between controller and projector and between one projector and another must be made with a 2
core-screened cable, with each core having at least a 0.5mm diameter. Connection to and from the projector is via
cannon 3 pin (which are included with the projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown
in the figure above.
Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of
the plug is not connected in any way other than as shown above. The projector accepts digital control signals in protocol
DMX512 (1990).
Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input
and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown
in the figure below.
TO CONTROLLER
DMX512 DMX IN DMX OUT
TO TERMINATER
DMX IN DMX OUT DMX IN DMX OUT

6/20
DMX TERMINATOR
In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This
prevents electrical noise from disturbing and corrupting the DMX control signals.
The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2 and 3, which is
then plugged into the output socket on the last projector in the chain. The connections are illustrated below.
SETUP OPTIONS-PROJECTOR CONFIGURATION
Projector configuration can be set conveniently via switch button and LCD display. Turn the projector on and the LCD
display will show DMX address you set and save last time and it can be reset and saved again as you please.
Launch the projector. Press button ENTER more than 5 seconds to unlock panel. After this, the display shows the
projector’s function menu and each option has its own sub-menus. Each menu stands for special function, see details as
follows.
Press button UP or DOWN if you want to browse through the various Setup Options.
Press button ENTER to save your settings or enter the next menu. Press button UP or DOWN to change the
values(plus or minus)
Press button FUNC, it will return to the upper menu one by one. If the button not pressed, defaulted will show display
status automatically.
TO SET THE DMX START ADDRESS
Each projector must be given a DMX start address so that the correct projector responds to the correct control signals.
This DMX start address is the channel number from which the projector starts to “listen” to the digital control information
being sent out from the controller. XR 200 BEAM has 2 DMX modes. There are standard mode and short mode. For
example standard mode have 14 channels, so set the No. 1 projector’s address 001, No. 2 projector’s address 015, No.
3 projector’s address 029, No. 4 projector’s address 043, and so on.
Launch the projector. Press button ENTER more than 5 seconds to unlock panel.
Press button ENTER to display DMX address;
Press button UP and DOWN, you can set the address;
21
3
120
DMX TERMINATOR
CONNECTION
Connect a 120 (OHM) resistor
across pins 2 and 3 in an XLR plug
and insert into the DMX out socket
on the last unit in the chain.
PIN 3
PIN 2

7/20
Press button ENTER to confirm; after powered next time, It will display latest values.
Press button FUNC, it will return to the upper menu one by one.
STAND-ALONE MODE
Operate the projector without connecting a controller, enable the master mode in the operation panel, the
projector will run in Stand-Alone mode automatically.
MASTER/SLAVE MODE
Without using a controller, many projectors can run synchronously in the Master/Slave mode by linking them
with each other. Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the
second fixture’s input and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX
terminator as shown in the figure below. Then the first one is the master with setting options as master mode
enabled, and others are slaves.
Start Address for all slaves is 001. The Master can run at any mode for the Master and Slaves run at the
corresponding mode compared to the Master.
After powered , the group will run at Master/Slave Mode.
.
OPERATION MENU
1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL
AddR XX
X
(
1~512
)
CNFG
(Config Settings)
dmX
(DMX Mode
,Default: STD)
S
Td
(
DMX Mode Standard
)
S
HR
T
(
DMX Mode Shor
t
)
LA-C
(Lamp Control
,Default: CHAN)
CHAN
(By Control Channel)
P
O
WE
(
B
y
Power
)
xyCH
(Pan Tilt Swap,
Default: OFF)
O
F
F
O
N
xyCP
(Pan Tilt Invert,
Default: OFF)
O
F
F
O
N
mOR
S
(Master/Slave Options,
Default: SLAV
)
SLAV
(Slave)
mAST
(Master 1)
INPUT OUTPUT
MASTER SLAVE SLAVE
INPUT OUTPUT INPUT DMXTERMINATOR

8/20
FACT
（Factory Default Settings?）
yES
TRmd
(Parameters transmitted(2)?)
yES
INFO
(Information)
TImE
(Lighting Fixture Use Time) XXXX (Time displayed)
TLAM
(Lamp Use Time)
XXXX
(Time displayed)
VER
(Version No.) X.X.X
(Software Version No.)
TEST
(Test Modes)
STOB
(Strobe)
NO
(Without Strobe)
STO1
(Strobe 1)
STO2
(Strobe 2)
COwH
(Color Wheel)
NO
(White)
Cw1-CW1
4
(Color Wheel1-Color
Wheel14
)
FORw
(Rotation)
STOP
(Rotation Stops)
REVE
(reverse Rotation)
FGwH
(Fixed Gobo Wheel)
NO
(White)_
FGw1-FGW17
(Gobo1-Gobo17)
FORw
(Rotation)
REVE
(Reverse Rotation)
GWS1-GWS10
(Shake Effect 1-10)
PRIS
(Prism)
NO
(Prism not used)
PR!
(Effect 1)
PR2
(Effect 2)
PR3
(Effect 3)
PR4
(Effect 4)
PRRO
(Prism Rotation)
STOP
(Rotation Stops)
FORw
(Rotation)
REVE
(Reverse Rotation)
FOCU
(Focus) 0-255
(Linear Focusing)
PAN 0-255
TILT 0-255
X&YS
(PAN and Tilt Speeds) 0-255
RESE
(Reset?) Yes

9/20
mENU
(Operating Menu)
Dmx
(DMX Mode)
PR XX
(Preset Memory,PR01-PR16)
ET XX
(User Memory,ET01~ET16）
CH1
(Strobe) 0-255
CH2
(Dimming) 0-255
CH3
(Color Wheel) 0-255
CH4
(Fixed Gobo Wheel) 0-255
CH5
(Prism Wheel) 0-255
CH6
(Prism Rotation) 0-255
CH7
(Focusing) 0-255
CH8
(Pan) 0-255
CH9
(Tilt) 0-255
CH10
(Pan and Tilt Speeds) 0-255
CH11
Scene hold time
0-255
Time=X*40mS
LAMP
（Manual Ignition）
L-ON
(Lamp ON) YES
L-OF
(Lamp Off) YES
Remark:
1. In the synchronous control of multiple projectors parameters can be transmitted from the master including:
DMX mode, display setting, operation mode(user memory);
2. all projectors Accepting parameters will automatically be set to slave mode.
REPLACING GOBOS
Disconnect the fixture from power. Lock Tilt. Carefully lift off the cover by unfastening the 4 screws and see the structure
shown as above..
COLOR WHEEL GOBO WHEEL

10/20
For the replacement of color wheels, it can be directly taken off by hands with due care. New color filters must be tightly
glued in right direction to the color wheel..
Gobo Replacement: Gobo wheel is taken off in the same direction as color wheel after it is taken off by hand. After the
new gobos are tightly inserted into the gobo wheel in the right direction and fixed gobo wheels installed, then the color
wheel should be re-installed.
Note: Color filter must not be touched by hands, it should be touched with glabrous, clean and soft tissue or cloth matted
between hand and glass instead of with bare hand.
Close the rear cover and fasten 4 screws and unlock tilt.

11/20
DMX PROTOCOL
Short
mode Standard mode FUNCTION DMX DESCRIPTION
1 1 Strobe
000-015 Open
016-255 Strobe from Slow to Fas
t
2 2 Dimmer
000-255 From dark to brigh
t
3
3
Color Wheel
000-095 White
096-103 Color 1
104-111 Color 2
112-119 Color 3
120-127 Color 4
128-135 Color 5
136-143 Color 6
144-151 Color 7
152-159 Color 8
160-167 Color
168-175 Color 10
176-183 Color 11
184-191 Color 12
192-199 Color 13
200-207 Color 14
208-223 Rotation （From slow to Fast）
224-239 Stops with White
240-255 Reverse Rotation（From slow to
Fast）
4
4
Fixed Gobo
Wheel
000-07 White
008-015 Gobo 1
016-023 Gobo 2
024-031 Gobo 3
032-039 Gobo 4
040-047 Gobo 5
048-055 Gobo 6
056-063 Gobo 7
064-071 Gobo 8
072-079 Gobo 9
080-087 Gobo 10
088-095 Gobo 11
096-103 Gobo 12
104-111 Gobo 13
112-119 Gobo 14
120-127 Gobo 15

12/20
128-135 Gobo 16
136-143 Gobo 17
144-159 Rotation （From slow to Fast）
160-175 Reverse Rotation （From slow to
Fast）
176-183 Shake 1（From Fast to slow）
184-191 Shake 2 （From Fast to slow）
192-199 Shake 3（From Fast to slow）
200-207 Shake 4（From Fast to slow）
208-215 Shake 5（From Fast to slow）
216-223 Shake 6（From Fast to slow）
224-231 Shake 7（From Fast to slow）
232-239 Shake 8（From Fast to slow）
240-247 Shake 9（From Fast to slow）
248-255 Shake 10（From Fast to slow）
5 5
Prism Wheel
000-063 White
064-127 Prism
128-191 Frost Filter
192-255 CT filter
6 6
Prism Rotation
000-063 Sto
p
064-127 Rotation （From slow to Fas
t
）
128-191 Sto
p
192-255 Reverse Rotation （From slow to
Fast）
7 7
Focusing 000-25
5
Linear Focusing
8
Focusing Fine 000-25
5
Focusing in 16 bit precision
8 9 Pan 000-255 Pan(0°~540°)
10
Pan Fine 000-255 Pan in 16 bit precision
9 11 Tilt 000-255 Tilt(0°~270°)
12 Tilt Fine 000-255 Tilt in 16 bit precision
13
Pan & Tilt
Speeds 000-255 Pan & Tilt Speed from Fast to Slow
10 14
Control
000-031 Reserved
032-063 Lamp Off (stop in DMX value for 2 s)
064-095 Reserved
096-127 Lamp On ( stop in DMX value for 2 s)
128-159 Reserved
160-191 Rese
t
( stop in DMX value for 2 s)
192-255 Reserved

13/20
INDICATION OF LED DIGITAL TUBE
Decimal point of the first digital tube On DMX signal OK
Off No DMX signal
Decimal point of the third digital tube On Master / slave signal is OK
Off No master / slave signal
Decimal point of the fourth digital tube On When setting master mode
Off When setting slave mode
Parameters that LED digital tubes display Flash Parameters not saved, press “ENTER” to save them
MAINTENANCE
If the projector’s lens becomes damaged or broken it should be replaced. If the lamp becomes damaged or deformed in
any way it must be replaced. If the light from the lamp appears dim this would normally indicate that it is reaching the end
of its life and it should be changed at once, aged lamps run to the extremity of their life might explode. If the projector
does not function, check the fuses on the power socket of the projector, they should only be replaced by fuses of the
same specification. Should these be damaged call a qualified technician before replacement. The projector has thermal
protection device that will switch off the projector in case of overheating, should either of these operate, check that the
fans are not blocked, and if they are dirty clean them before switching on the projector again. Check that the fans are
operational, if not call a qualified technician.
Any maintenancework should only be carried out by qualified technicians.
LUBRICATION
To ensure the continuous rotation of the rotating gobos and linear motion of the lens for focusing, it is recommended that
the bearings for the rotating gobos and the 2 shafts for the focusing lens holder be lubricated periodically, preferably
every two months. Use only high quality, high-temperature resistant grease instead of any type of oil. When lubricating
the bearings, a syringe with a fine needle is the easiest way to introduce the grease to the bearings around each gobo.
KEEPING THE PROJECTOR CLEAN
To ensure the reliability of the projector it should be kept clean. It is recommended that the fans should be cleaned every
15 days. The lens and dichroic colour filters should also be regularly cleaned to maintain an optimum light output. Do
NOT use any type of solvent on dichroic colour filters.
Cleaning frequency depends on the environment in which the fixture operates: damp, smoke or particularly dirty
surroundings can cause greater accumulation of dirt on the unit’s optics. A soft cloth and typical glass cleaning products
should be used in cleaning. It is recommended to clean the external optics at least once every 20 days and clean the
internal optics at least once every 30 / 60 days.
Do not use any organic solvent, e.g. alcohol, to clean the reflector mirror, dichroic colour filters or housing of
the apparatus.

14/20
TROUBLESHOOTING
PROBLEM ACTION
The projector doesn’t switch on
¾Check the fuse on the power socket.
¾Replace the lamp.
The lamp comes on but the projector
doesn’t respond to the controller
¾Make sure that the fixture’s start address is right
¾Replace or repair the XLR singal cable.
The projector only functions intermittently
¾Make sure the fan is working well or fans and their filters not
blocked
Defective projection
¾Make sure the lamp is within its life limit
¾Remove dust or grease from the lenses.
The project image appears to have a halo
¾Make sure the lamp is installed correctly.
¾Carefully clean the optical group lenses and the projector
components.
The beam appears dim
¾Check the optics is clean or the lens in good condition(not
cracked)
¾Replace with a new lamp of the specified type and rating.

15/20
TECHNICAL DATA
VOLTAGES:
100V/200V/220V/230V/240V AC，50/60Hz
POWER CONSUMPTION:
280W@220V
LAMP:
PHILIPS MSD Platinum 5R
Colour Temperature 8000°K
Manufacturers Rated Lamp Life 2000 小时
Color s:
1 Color Wheel
14 dichroic colour filters plus white
variable speed and bi-directional rainbow effect
linear colour changing is available
GOBOS:
1 Fixed gobo wheel :
17 interchangeable gobos+ white
Shaking and bi-directional wheel scrolling at variable speeds
Gobo changing is available
Prism/Frost Wheel
8-facet rotating Prism(bi-directional with variable speeds)+CT filter+ Frost Filter + White
Focusing
0-100% linearly adjustable by Dmx
STROBE:
Double shutter blades, 0.3~20 F.P.S
HEAD MOVEMENT:
Pan 540º, Tilt 270º with auto position correction
BEAMANGLE
0°～4°, Linear zoom
CONTROL:
DMX512, 3 pin and 5 pin interfaces

16/20
10 channels in short mode, 14channels in standard mode
Self-test mode
OTHER FUNCTIONS:
Adjustable Pan & Tilt speed
Fixture and lamp usage time display
Modular construction for easy maintenance
DMX512 wireless receiver
DMX512 wireless transmitter (optional)
HOUSING:
Composite plastic, IP20
Power driven water proof cover, optional, water proof system control by DMX, IP44
WEIGHT:
16Kg
SIZES:

17/20

1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
D D
C C
B B
A A
Title
DESIGN
FILE
A 2
PR-2203 XR 200 Beam PR-2203 XR 200 Beam .SCH Trevor
VER :1.0.0
PR
CHANGE DATA: 2012/05/22 PRINT DATA: 2012/05/22
NO
page 1 of 1
NL
E
6.3A250V
Power Interface
Fuse
Switch
X1-1 X1-3
X3-4 X3-1
1
2
3
4
5
Lamp Driver 040070109 EUC 190d N/T01
X1 X3 + -
FG N
+
-
L
Power Supply
190010116 K18-UP400
CN2CN1
Lamp 100070026:MSD Platinum 5 R
L N
-V
+V
FG
+V
-V
Power Supply 190010113 K18-UP200S24
10 9 8 7 6 5 4 3 2 1
S-
S+
+5V
ISS
Y
GND
R
G1
B1
GND
A+ B- GND GND V+
W1
Y R
G2
B2
GND
W2
GND
DQ
+5V
Master Control Display
P/ N:230060122
WRISS DMX POWER
LED3 SOUT
PWM2 PWM1
TEMP
3 2 1 4 5 6 7 8 9
10
Wireless Rec eive Board
2 1
3
Male 3XRL
1 2
3
Female 3XRL
1
2
3
Male 5XRL Female 5XRL
4
5 5
4
3
2
1
4 3 2 1 GND +24V 4 3 2 1
Y2
VLED
GND
VLED
X2
X1
GND
Y1
+5V
B
GND
B
GND
A
GND
S
V
GND
S
V
A
X-Y Motor Driver
P/N:230060123
MY MX POWER
HY HX
SY SX DMXOUT DMXIN
Tilt
Motor
Pan
Motor
V
G
S
Tilt
Hall Sensor
V
G
S
Pan Hall Sensor
S2
S1
G
V
Tilt
Optic Coupling
S2
S1
G
V
Pan Optic Coupling
1
2
3
4
A+
B-
GND
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
+ -
GND
S
+5V
GND
S
+5V
GND
S
+5V
GND
S
+5V
7-Channel Motor Driver
P/N:230060125
M10 M9 M7 M5 M4 M3 M1
POWER
IN
Shutter
Two-Motor
Fix-Gobo Motor
Colour Motor
Effect Motor
Zoom
Two-Motor
R-Prism Motor
V G S
Colour Hall Sensor
V G S
Fix-Gobo Hall Sensor
V
G
S
Zoom Hall Sensor
V
G
S
Effect
Hall Sensor
S7 S6
S3 S2
Base Fan
Housing
Temperature Switch
G
S
V
Temperature Board
Head Fan

19/20
COMPONENT ORDER CODES
NAME PART NO. QUANTITY REMARK
5R Ballast 040070109 1
5R Lamp 100070026 1
200W Power Switch 190010110 1
400W Power Switch 190010116 1
Fuse 270041065 1 T20A250V 6.3*32mm
Pan Driver Belt 290151322 1 HTD-531-3M
Tilt Driver Belt 290151331 1 HTD-399-3M
Prism Wheel Belt 290151255 1 HTD-270-3M
Focusing Belt 290151310 1 72MXL
O SHAPE RUBBER RING 290260054 1
FAN 030069055 2
TURBO-FAN 030069068 1 WITH SQUARE BASE
TURBO-FAN 030069072 1
BASE FAN 030069005 3
PAN MOTOR 030040160 1
TILT MOTOR 1
PRISM MOTOR
030040154
1
FIXED GOBO WHEEL MOTOR 1
COLOR WHEEL MOTOR 1
PRISM ROTATION MOTOR
030040095
1
FOCUSING MOTOR 2
STROBE MOTOR 2
PAN & TILT DRIVER BOARD 230060123 1
7 CHANNEL DRIVER BOARD 230060125 1
DISPLAY BOARD 230060122 1
COLOR WHEEL ACCESSORIES 120110366 1
FIXED GOBO WHEEL ACCESSORIES 120110367 1
PRISM WHEEL ACCESSORIES 120110369 1

20/20
PR LIGHTING LTD.
1582 Xingye Avenue, Nancun Panyu
Guangzhou, 511442 China
TEL: [phone]
FAX: [phone]
P/N: 320020086
Version: 20120628 (Preliminary）