PR Lighting PR-2330 User manual

XL Beam 300
PR-2330/2330M
This product manual contains important information about the safe installation and use of this
projector. Please read and follow these instructions carefully and keep this manual in a safe place
for future reference.
PR LIGHTING LTD.
http://www.pr-lighting.com

2/26
INDEX
SAFE USAGE OF THE PROJECTOR 3
INSTALLING THE PROJECTOR 4
FITTING THE LAMP 4
POWER SUPPLY – MAINS 5
CONTROL CONNECTIONS 5
DMX TERMINATOR 6
SETUP OPTIONS-PROJECTOR CONFIGURATION 6
TO SET THE DMX START ADDRESS 6
MASTER/SLAVE MODE 7
STAND-ALONE MODE 7
OPERATION MENU 8
ERROR MESSAGES 12
REPLACING GOBOS 12
DMX PROTOCOL 13
LED INDICATION 16
MAINTENANCE 16
LUBRICATION 16
KEEPING THE PROJECTOR CLEAN 16
TROUBLESHOOTING 17
TECHNICAL DATA 18
ELECTRICAL DIAGRAM 22
COMPONENT ORDER CODES 24
Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without
notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of
product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence
arising from them.
Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good
condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the
unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.
ACCESSORIES
These items are packed together with the projector:
Name Quantity Unit Remark
G clamps 2 Pcs
3-pin XLR connector 1 Set Without cable
Safety cord 1 Pc
This manual 1 Pc
Ωclamps 2 Pcs Options

3/26
SAFE USAGE OF THE PROJECTOR
When unpacking and before disposing of the carton check there is no transportation damage before using the projector.
Should there be any damage caused by transportation, consult your dealer and do not use the apparatus.
The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture,
excessive heat, humidity and dust. Do not allow contact with water or any other liquids.
The projector is not designed or intended to be mounted directly on to inflammable surfaces.
The projector is only intended for installation, operation and maintenance by qualified personnel.
The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent wall surfaces. Be sure
that no ventilation slots are blocked.
Do not project the beam onto inflammable surfaces, minimum distance is 5m. 5m
Avoid direct exposure to the light from the lamp. The light is harmful to the eye.
Do not attempt to dismantle and/or modify the projector in any way.
Electrical connection must only be carried out by qualified personnel.
Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector.
It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.
Do not connect this device to any other types of dimmer apparatus.
Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cord come into contact
with other cables. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.
Keep the lamp clean. Do not touch the lamp glass with bare hand.
The projector should always be installed with a secondary safety fixing. A safety cord is supplied for this; it should be
attached as shown in “installing the projector” section.
The lamp used in this projector is a discharge lamp. After switching off don’t attempt to restart the projector until lamp has
cooled, this will require approx 15 minutes. Switching the lamp on and off at short intervals will reduce the life of both the
lamp and the projector. But occasional breaks will prolong the life of the lamp and projector.
Never run the projector without a lamp.
The lamp shall be changed if it has become damaged or thermally deformed.
Shields and lens shall be changed if they have become visibly damaged to such an extent than their effectiveness is
impaired, for example by cracks or deep scratches.
Exterior surface temperatures of the luminaire after 5 minutes operation is 40℃, when steady state is achieved 50℃,
There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the
covers removed.
Always disconnect from the mains, when the device is not in use or before cleaning it or
before attempting any maintenance work !
If you have any questions, don’t hesitate to consult your dealer or manufacturer.

4/26
INSTALL THE PROJECTOR
Take 2 clamps and the safety cord out from the package and mount 2 clamps on the underside of fixture with 2 retainers
attached to each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the
WARNING on the underside of the base as shown above) To pass the SAFETY CORD through 2 HOLES for safety!
Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning. Always ensure that
the structure that you are going to mount the projector to is secure and is strong enough to support a weight of XL Beam
300.
WARNING:
1. Unlock the PAN and TILT before the 1st application of projector for safety.
2. The projector MUST be lifted or carried by the HANDLES instead of clamps.
3. For safety the safety cord should afford 10 times of the unit’s weight.
FITTING THE LAMP
Lock the yoke before fitting/replacing the lamp.
Open the cover board at the rear of the projector by loosening 3 screws, you can see the structure as shown in the figure
above.
Gently pull out the lamp holder assembly.
Take out the worn-out lamp. Insert the new lamp to the socket. Note: don’t touch the bulb of the new lamp with bare
hands so as not to influence the beam output.
Close the rear cover and fasten 3 screws.
WARNING: The MSD series are high-pressure lamps with external igniters ( ). Care should always be taken
when handling these lamps.Always read the manufacturers "Instructions for use" enclosed with the lamp.

5/26
POWER SUPPLY-MAINS
Connect the power cord as follows:
L (live) =brown
E (earth) =yellow/green
N (neutral) =blue
Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked
on the panel of the projector. It is recommended that each projector be supplied separately so that they may be
individually switched on and off.
IMPORTANT
It is essential that each projector is correctly earthed and the electrical installation conforms to all relevant
standards.
CONTROL CONNECTION
Connection between controller and projector and between one projector and another must be made with a 2
core-screened cable, with each core having at least a 0.5mm diameter. Connection to and from the projector is via
cannon 3 pin (which are included with the projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown
in the figure above.
Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of
the plug is not connected in any way. The XL Beam 300 accepts digital control signals in protocol DMX512 (1990).
Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input
and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown
in the figure below.

6/26
DMX TERMINATOR
In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This
prevents electrical noise from disturbing and corrupting the DMX control signals.
The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2 and 3, which is
then plugged into the output socket on the last projector in the chain. The connections are illustrated below.
21
3
120
DMX TERMINATOR
CONNECTION
Connect a 120 (OHM) resistor
across pins 2 and 3 in an XLR plug
and insert into the DMX out socket
on the last unit in the chain.
PIN 3
PIN 2
SETUP OPTIONS-PROJECTOR CONFIGURATION
Projector configuration can be set conveniently via pressbutton switch and LCD display. Turn the projector on and the
LCD display will show DMX address you set and saved last time and it can be reset and saved again as you please.
Launch the projector and press button ENTER for more than 5 seconds to unlock the panel, the LCD will show the
function menu of the projector, each main menu has its submenus and each submenu has a specific function. For
details, please see the “OPERATION MENU” section.
Press button UP or DOWN if you want to browse through the various Setup Options. Press button ENTER to save your
settings or enter the next menu.
Press button UP or DOWN to shift.
Press button FUNC, it will return to the upper menu one by one. If you stay for minutes defaulted will show display status
automatically.
TO SET THE DMX START ADDRESS
Each XL Beam 300 must be given a DMX start address so that the correct projector responds to the correct control
signals. This DMX start address is the channel number from which the projector starts to “listen” to the digital control
information being sent out from the controller. The XL Beam 300 has 3 DMX modes. There are standard mode,
extended mode and short mode. For example standard mode has 19 channels, so set the No. 1 projector’s address 001,
No. 2 projector’s address 020, No. 3 projector’s address 039, No. 4 projector’s address 058, and so on.
Launch the projector. Press button ENTER more than 5 seconds to unlock panel.
Press button FUNC to display DMX address;

7/26
Press button UP and DOWN, you can set the address;
Press button ENTER to confirm; In the same time. The GREEN LED will flash one time. It means the setting has
been enabled.
Press button FUNC, it will return to the upper menu one by one.
STAND-ALONE MODE
Operate the projector without connecting a controller, enable the master mode in the operation panel, the
projector will run in Stand-Alone mode automatically.
MASTER/SLAVE MODE
Without using a controller, many projectors can run synchronously in the Master/Slave mode by linking them
with each other. Select one projector as the master with setting options master mode enabled but slaves.
Regard the other projectors as the slaves with setting options slave mode enabled and all DMX start
address “001”.
Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input
and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown
in the figure below.

8/26
OPERATION MENU
1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL 5th LEVEL 6th LEVEL
PR LIGHTING
XL
SERIES
XL BEAM 300
PR LIGHTING
DMX Address
PR LIGHTING
DMX Address
XXX
PR LIGHTING
Reset
PR LIGHTING
Reset
Are you sure
PR LIGHTING
Config Settings
PR LIGHTING
DMX Mode
PR LIGHTING
DMX Mode
Standard
PR LIGHTING
DMX Mode
Extended
PR LIGHTING
DMX Mode
Short
PR LIGHTING
Loss of DMX
PR LIGHTING
When DMX is Lost
Normal Time Out
PR LIGHTING
When DMX is Lost
Hold Last Value
PR LIGHTING
Lamp Control
PR LIGHTING
Lamp Control By
Control Channel
PR LIGHTING
Lamp Control By
Power On
PR LIGHTING
Lamp Control By
DMX Present
PR LIGHTING
Option Settings
PR LIGHTING
Colour Positions
PR LIGHTING
Colour Positions
STEPPED
PR LIGHTING
Colour Positions
LINEAR
PR LIGHTING
Pan DMX Invert
PR LIGHTING
Pan DMX Invert
OFF
PR LIGHTING
Pan DMX Invert
ON
PR LIGHTING
Tilt DMX Invert
PR LIGHTING
Tilt DMX Invert
OFF
PR LIGHTING
Tilt DMX Invert
ON
PR LIGHTING
Pan Tilt Swap
PR LIGHTING
Pan Tilt Swap
OFF
PR LIGHTING
Pan Tilt Swap
ON
PR LIGHTING
Dimmer Invert
PR LIGHTING
Dimmer Invert
OFF
PR LIGHTING
Dimmer Invert

9/26
ON
PR LIGHTING
Iris Invert
PR LIGHTING
Iris Invert
OFF
PR LIGHTING
Iris Invert
ON
PR LIGHTING
Zoom Invert
PR LIGHTING
Zoom Invert
OFF
PR LIGHTING
Zoom Invert
ON
PR LIGHTING
CYM Invert
PR LIGHTING
CYM Invert
OFF
PR LIGHTING
CYM Invert
ON
PR LIGHTING
Defaults
PR LIGHTING
Defaults
OFF
PR LIGHTING
Defaults
Restore Defaults
PR LIGHTING
Display Options
PR LIGHTING
Display Mode
PR LIGHTING
Display Mode
On Always
PR LIGHTING
Display Mode
Off After Delay
PR LIGHTING
Display Invert
PR LIGHTING
Display Invert
OFF
PR LIGHTING
Display Invert
ON
PR LIGHTING
Display Dimming
PR LIGHTING
Disp Dim Level
XXX(Min,1~9,Full),
Default is 8)
PR LIGHTING
Display Contrast
PR LIGHTING
Display Contrast
XX(0~20, Default
is 10)
PR LIGHTING
Information
PR LIGHTING
Lamp Hours
PR LIGHTING
Lamp Hours=
XX
PR LIGHTING
Reset Lamp Hours
Are You Sure?
PR LIGHTING
Total Hours
PR LIGHTING
Total Hours=XX
PR LIGHTING
Temperature
PR LIGHTING
Driver Board
PR LIGHTING
Driver Board=
XX℃
PR LIGHTING
Head Sensor
PR LIGHTING
Head Sensor=
XX ℃
PR LIGHTING
Software Version
PR LIGHTING
Display Board
PR LIGHTING
Display Board=
X.X.X
PR LIGHTING
View DMX Values
PR LIGHTING
DMX Channel
1=0
PR LIGHTING
Electronic SN
PR LIGHTING
Electronic SN=
=************
PR LIGHTING
Test Modes
PR LIGHTING
Factory Setup
PR LIGHTING
Factory Setup
OFF
PR LIGHTING

10/26
Factory Setup
ON
PR LIGHTING
Self Test
PR LIGHTING
Self Test
OFF
PR LIGHTING
Self Test
ON
PR LIGHTING
Lamp Manual
Control
PR LIGHTING
Lamp Status
PR LIGHTING
Status = XX
Control = XX
PR LIGHTING
Turn Lamp On
PR LIGHTING
Turn Lamp Off
PR LIGHTING
Operation Mode
PR LIGHTING
Operation Mode=
DMX Operation
PR LIGHTING
Operation Mode=
Master Mode
PR LIGHTING
Select Memory
User Memory 1
PR LIGHTING
Select Memory
User Memory 2
PR LIGHTING
Select Memory
Preset Memory
1
PR LIGHTING
Select Memory
Preset Memory 2
PR LIGHTING
Select Memory
Preset Memory
3
PR LIGHTING
Operation Mode=
Slave Mode
PR LIGHTING
Select Memory
User Memory 1
PR LIGHTING
Select Memory
User Memory 2
PR LIGHTING
Select Memory
Preset Memory
1
PR LIGHTING
Select Memory
Preset Memory 2
PR LIGHTING
Select Memory
Preset Memory
3
PR LIGHTING
Mode=
Static Scene
PR LIGHTING
User Memories
PR LIGHTING
Edit User Memory
PR LIGHTING
User Memory 1
PR LIGHTING
Scene XX
（1~28）
PR LIGHTING
Shutter
PR LIGHTING
Shutter
XXX
PR LIGHTING
Dimmer
PR LIGHTING
Dimmer
XXX
PR LIGHTING
CYM Macro
PR LIGHTING
CYM Macro
XXX
PR LIGHTING
Cyan
PR LIGHTING
Cyan
XXX
PR LIGHTING
Yellow
PR LIGHTING
Yellow

11/26
XX
X
PR LIGHTING
Magenta
PR LIGHTING
Magenta
XXX
PR LIGHTING
Color
PR LIGHTING
Color
XXX
PR LIGHTING
Iris
PR LIGHTING
Iris
XXX
PR LIGHTING
R Gobo Wheel
PR LIGHTING
R Gobo Wheel
XXX
PR LIGHTING
R Gobo Rotate
PR LIGHTING
R Gobo Rotate
XXX
PR LIGHTING
Focus
PR LIGHTING
Focus
XXX
PR LIGHTING
Zoom
PR LIGHTING
Zoom
XXX
PR LIGHTING
Pan Coarse
PR LIGHTING
Pan Coarse
XXX
PR LIGHTING
Pan Fine
PR LIGHTING
Pan Fine
XXX
PR LIGHTING
Tilt Coarse
PR LIGHTING
Tilt Coarse
XXX
PR LIGHTING
Tilt Fine
PR LIGHTING
Tilt Fine
XXX
PR LIGHTING
M-Speed
PR LIGHTING
M-Speed
XXX（000~255）
PR LIGHTING
Delay
PR LIGHTING
Delay
XX Seconds
（0.25s~100min）
PR LIGHTING
Link To Step
PR LIGHTING
Link To Step
XXX（1~28）
PR LIGHTING
User Memory 2
PR LIGHTING
Scene
XXX（1~28）
PR LIGHTING
Shutter
PR LIGHTING
Shutter
XXX
PR LIGHTING
Dimmer
PR LIGHTING
Dimmer
XXX
PR LIGHTING
CYM Macro
PR LIGHTING
CYM Macro
XXX
PR LIGHTING
Cyan
PR LIGHTING
Cyan
XXX
PR LIGHTING
Yellow
PR LIGHTING
Yellow
XXX
PR LIGHTING
Magenta
PR LIGHTING
Magenta
XXX
PR LIGHTING
Color
PR LIGHTING
Color
XXX
PR LIGHTING
Iris
PR LIGHTING
Iris
XXX
PR LIGHTING
R Gobo Wheel
PR LIGHTING
R Gobo Wheel
XXX

12/26
PR LIGHTING
R Gobo Rotate
PR LIGHTING
R Gobo Rotate
XXX
PR LIGHTING
Focus
PR LIGHTING
Focus
XXX
PR LIGHTING
Zoom
PR LIGHTING
Zoom
XXX
PR LIGHTING
Pan Coarse
PR LIGHTING
Pan Coarse
XXX
PR LIGHTING
Pan Fine
PR LIGHTING
Pan Fine
XXX
PR LIGHTING
Tilt Coarse
PR LIGHTING
Tilt Coarse
XXX
PR LIGHTING
Tilt Fine
PR LIGHTING
Tilt Fine
XXX
PR LIGHTING
M-Speed
PR LIGHTING
M-Speed
XXX（000~255）
PR LIGHTING
Delay
PR LIGHTING
Delay
XX Seconds
（0.25s~100min）
PR LIGHTING
Link To Step
PR LIGHTING
Link To Step
XXX（1~28）
PR LIGHTING
Static Scene
PR LIGHTING
Shutter
PR LIGHTING
Shutter
XXX
PR LIGHTING
Dimmer
PR LIGHTING
Dimmer
XXX
PR LIGHTING
CYM Macro
PR LIGHTING
CYM Macro
XXX
PR LIGHTING
Cyan
PR LIGHTING
Cyan
XXX
PR LIGHTING
Yellow
PR LIGHTING
Yellow
XXX
PR LIGHTING
Magenta
PR LIGHTING
Magenta
XXX
PR LIGHTING
Color
PR LIGHTING
Color
XXX
PR LIGHTING
Iris
PR LIGHTING
Iris
XXX
PR LIGHTING
R Gobo Wheel
PR LIGHTING
R Gobo Wheel
XXX
PR LIGHTING
R Gobo Rotate
PR LIGHTING
R Gobo Rotate
XXX
PR LIGHTING
Focus
PR LIGHTING
Focus
XXX
PR LIGHTING
Zoom
PR LIGHTING
Zoom
XXX
PR LIGHTING
Pan Coarse
PR LIGHTING Pan
Coarse
XXX

13/26
PR LIGHTING
Pan Fine
PR LIGHTING Pan
Fine
XXX
PR LIGHTING
Tilt Coarse
PR LIGHTING
Tilt Coarse
XXX
PR LIGHTING
Tilt Fine
PR LIGHTING
Tilt Fine
XXX
PR LIGHTING
M-Speed
PR LIGHTING
M-Speed
XXX（000~255）
PR LIGHTING
Init User Memory
PR LIGHTING
Reset
Static Scene
PR LIGHTING
Reset Static Scn
<Unlock> 2 3 & 4
(Press buttons
UP,DOWN and
ENTER)
PR LIGHTING
Static Scene Has
Been Reset
PR LIGHTING
Reset User
Memory 1
PR LIGHTING
Reset User 1 ?
<Unlock> 2 3 & 4？
PR LIGHTING
Memory 1 Has
Been Reset
PR LIGHTING
Reset User
Memory 2
PR LIGHTING
Reset User 2 ?
<Unlock> 2 3 & 4
PR LIGHTING
Memory 2 Has
Been Reset

14/26
ERROR MESSAGES
In the course of launch, XL Beam 300 examines automatically whether there are errors and if there are, it will display
information as follows:
Display Message
Sensor Error M1 Motor 1 (Focus) error
Sensor Error M2 Motor 2 (Rotating Gobo wheel) error
Sensor Error M3 Motor 5 (Gobo rotation) error
Sensor Error M6 Motor 6 (Colour wheel) error
Sensor Error M8 Motor 7 (CYM-magenta) error
Sensor Error M9 Motor 9 (CYM-yellow) error
Sensor Error M10 Motor 10 (CYM-cyan) error
REPLACING GOBOS
Disconnect the fixture from power. Lock Tilt. Carefully lift off the rear cover by undoing the 4 screws.
For gobos replacement: Remove the gobo holder with gobo from gobo wheel by hands.
Pull out the spring and drop the old gobo out of the holder.
Insert the new gobo into the holder, and then insert the spring with the narrow end against the gobo.
Push the end of the spring in under lip of the holder.
Pick the spring clip up and put the gobo holder back into the position, if necessary, a small screwdriver will be
helped.
Note: If the gobo is a glass one, it should be touched with glabrous, clean and soft tissue or cloth matted between hand
and glass instead of with bare hand.
Close the rear cover and fasten 4 screws.

15/26
DMX PROTOCOL
Short
mode Standard mode Extended mode FUNCTION DMX DESCRIPTION
1 1 1 Strobe
000-009 Black
010-020 Open
021-244 Strobe speed from slow to fast
245-255 Open
2 2 2 Dimmer 000-255 Dimming from dark to light (0-100%)
3 Dimmer Fine 000-255 Dimmer in 16 Bit precision
3 3 4 CYM Macro
000-016 White
017-035 Red
036-054 Yellow
055-073 Green
074-092 Cyan
093-110 Blue
111-128 Magenta
129-255 Rainbow rotation from slow to fast
4 4 5 Cyan 000-255 Cyan from shallow to deep
6
Cyan 16Bi
t
000-25
5
Cyan in 16 Bit precision
5
5
7
Yellow 000-25
5
Yellow from shallow to dee
p
8
Yellow 16Bi
t
000-25
5
Yellow in 16 Bit precision
6
6
9
Magenta 000-25
5
Magenta from shallow to dee
p
10 Magenta 16Bi
t
000-25
5
Magenta in 16 Bit precision
7 7 11 Colour Wheel
000-024 White
02
5
-040 Colour 1
041-056 Colour 2
057-072 Colour 3
073-088 Colour 4
089-104 Colour 5
105-120 Colour 6
121-127 Colour 7
12
8
-18
7
R
otation from slow to fas
t
18
8
-19
5
S
top in current position
19
6
-25
5
R
everse rotation fr
o
m slow to fas
t
8 8 12 Iris
000-13
5
Iris from large to small
136-167 Iris opens slow and closes fast,
speed from slow to fas
t
168-199 Iris closes slow and opens fast,
speed from slow to fas
t
200-231 Iris opens and closes with the same
speed from slow to fas
t
232-25
5
Minimal
9 9 13
Rotating Gobo
Wheel
000-016 white
017-032 Gobo1
033-048 Gobo 2
049-064 Gobo 3
065-080 Gobo 4
081-096 Gobo 5
097-112 Gobo 6

16/26
113-127 Gobo 7
128-150 Rotation speed from slow to fast
151-171 Reverse rotation from slow to fast
172-183 Gobo shake 1 from slow to fast
184-195 Gobo shake 2 from slow to fast
196-207 Gobo shake 3 from slow to fast
208-219 Gobo shake 4 from slow to fast
220-231 Gobo shake 5 from slow to fast
232-243 Gobo shake 6 from slow to fast
244-255 Gobo shake 7 from slow to fast
10 10 14 Gobo rotation
000-128 index
129-188 Gobo rotation from slow to fast
189-195 Stop rotating
196-255 Reverse rotation from slow to fast
11 15
Gobo rotation
16 Bi
t
000-255 Gobo rotation in 16 Bit precision
11 12 1
6
Focus 000-25
5
Linearly focusing
1
7
Focus Fine 000-25
5
Focus in 16 precision
12 1
3
1
8
Zoom 000-25
5
From small to large
1
3
14 1
9
Pan 000-25
5
Pan rotation 540°
1
5
20 Pan Fine 000-25
5
Pan rotation in 16 precision
14 1
6
21 Til
t
000-25
5
Tilt rotation 270°
1
7
22 Tilt Fine 000-25
5
Tilt rotation in 16 precision
18 23 Pan & Tilt
speed 000-255 Pan &Tilt speed from fast to slow
15 19 24 Control
000-047 Reserved
048-080 Reset
081-112 Reserved
113-144 Lamp off ( stop in DMX value for 10 s)
145-168 Reserved
169-200 Lamp power reduced to 50%
201-223 Reserved
224-255 Lamp on (See remark below)
Remark:
If you intend to turn on/off the lamp via the last channel of the controller, don’t attempt to push the channel to value
224-255 immediately after turning it off, or push the slide bar to value 224-255 to wait it cooling. Under these 2
circumstances, the lamp can not be turned on. The right operation is: turn it off---cool down---push the slide bar to turn it
on.

17/26
LED INDICATION
Green
On DMX signal OK
Off No DMX signal
Flash DMX signal error
Yellow On
Setting the panel
Blue On Power
Red/Green Red Running slave mode or self test mode
Green Running master mode
MAINTENANCE
If the projector does not function, check the fuses on the power socket of the projector, they should only be replaced by
fuses of the same specification. Should these be damaged call a qualified technician before replacement. The projector
has thermal protection device that will switch off the projector in case of overheating, should either of these operate,
check that the fans are not blocked, and if they are dirty clean them before switching on the projector again. Check that
the fans are operational, if not call a qualified technician.
Any maintenancework should only be carried out by qualified technicians.
LUBRICATION
To ensure the continuous rotation of the rotating gobos, it is recommended that the bearings for the rotating gobos be
lubricated periodically, preferably every two months. Use only high quality, high-temperature resistant grease instead of
any type of oil. When lubricating the bearings, a syringe with a fine needle is the easiest way to introduce the grease to
the bearings around each gobo.
KEEPING THE PROJECTOR CLEAN
To ensure the reliability of the projector it should be kept clean. It is recommended that the fans should be cleaned every
15 days. The lens and dichroic colour filters should also be regularly cleaned to maintain an optimum light output. Do
NOT use any type of solvent on dichroic colour filters.
Cleaning frequency depends on the environment in which the fixture operates: damp, smoke or particularly dirty
surroundings can cause greater accumulation of dirt on the unit’s optics. A soft cloth and typical glass cleaning products
should be used in cleaning. It is recommended to clean the external optics at least once every 20 days and clean the
internal optics at least once every 30 / 60 days.
Do not use any organic solvent, e.g. alcohol, to clean the reflector mirror, dichroic colour filters or housing of
the apparatus.

18/26
TROUBLESHOOTING
PROBLEM ACTION
The projector doesn’t switch on
¾Check the fuse on the power socket.
¾Replace the lamp.
The lamp comes on but the projector
doesn’t respond to the controller
¾Make sure that the projector is correctly configurated.
¾Replace or repair the DMX cable.
The projector only functions intermittently ¾Make sure the fan is working and not dirty.
Defective projection
¾Check the lenses are not broken.
¾Remove dust or grease from the lenses.
The project image appears to have a halo
¾Make sure the lamp is installed correctly.
¾Carefully clean the optical group lenses and the projector
components.
The beam appears dim
¾Check the optics is clean.
¾Replace with a new lamp of the specified type and rating.

19/26
TECHNICAL DATA
VOLTAGES:
Electronical ballast（PR-2330）: 100V/120V/200V/220V/230V/240V AC，50/60Hz
Magnetic ballast（PR-2330M）: 100V/120V/200V/220V/30V/240V AC，50/60Hz
POWER CONSUMPTION:
Electronical ballast（PR-2330）: 400W@220V
Magnetic ballast（PR-2330M）: 470W@220V
LAMP:
PHILIPS MSD Gold 300/2 FastFit
Colour Temperature 8000°K
Lumen output 22000 lm
Socket PGJX28, single ended
Manufacturers Rated Lamp Life 750 Hours replacement
COLOURS:
Linear CYM colour mixing system (8-or 16-bit) with macro function
1 wheel with 7 dichroic colour filters plus white
With variable speed bi-directional rainbow effect
Step/linear colour changing is available
GOBOS:
1 Rotating gobo wheel:
7 interchangeable gobos+ white
Indexable, bi-directionally rotatable at variable speeds
bi-directionally scrolling at variable speeds
Gobo shake function
Gobo diameter: 25.7mm, image diameter: 23mm
IRIS
0-100% linearly adjustable(8- or 16-bit)
Macro
FOCUS
DMX controlled focus
DIMMER:
0-100% linearly adjustable
SHUTTER:
Single shutter blade, 0.3~10 F.P.S

20/26
HEAD MOVEMENT:
Pan 540º, Tilt 245º with auto position correction
8- or 16-bit
BEAMANGLE:
Standard: 6 º
With Light Frost: 9 º
With heavy Frost: 20 º
CONTROL:
DMX512, 3 pin, 5 pin interfaces
15 channels in short mode, 19 channels in standard mode, and 24 channels in extended mode.
RDM protocol ready
Master / slave mode
Stand-alone mode
Self-test mode
OTHER FUNCTIONS:
Adjustable Pan &Tilt speed
Fixture and lamp usage time display
LCD display menu in English
Energy saving function of the ballast
Adjustable fan speed
Built-in analyzer for easy fault finding, error messages
Input signal isolating protection
HOUSING:
Composite plastic, IP20
WEIGHT:
Electronical ballast（PR-2330）: 17Kg
Magnetic ballast（PR-2330M）: 24Kg
SIZES:
See at below