PR Lighting XL 1500 User manual

XL WASH 1500
PR-2805/PR-2805M
This product manual contains important information about the safe installation and use of this
projector. Please read and follow these instructions carefully and keep this manual in a safe place
for future reference.
PR LIGHTING LTD.
http://www.pr-lighting.com

2/22
INDEX
SAFE USAGE OF THE PROJECTOR 3
INSTALLING THE PROJECTOR 4
FITTING THE LAMP 4
POWER SUPPLY – MAINS 5
CONTROL CONNECTIONS 5
DMX TERMINATOR 6
SETUP OPTIONS-PROJECTOR CONFIGURATION 6
TO SET THE DMX START ADDRESS 6
OPERATION MENU 7
ERROR MESSAGES 10
DMX PROTOCOL 11
LED INDICATION 14
MAINTENANCE 14
LUBRICATION 14
KEEPING THE PROJECTOR CLEAN 14
TROUBLESHOOTING 15
TECHNICAL DATA 16
ELECTRICAL DIAGRAM 19
COMPONENT ORDER CODES 20
Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without
notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of
product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence
arising from them.
Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good
condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the
unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.
ACCESSORIES
These items are packed together with the projector:
Name Quantity Unit Remark
G clamps 2 Pcs
XLR cable 1 Pc 3-pin plug
Safety cords 2 Pcs
This manual 1 Pc
Ωclamps 2 Pcs Options

3/22
SAFE USAGE OF THE PROJECTOR
When unpacking and before disposing of the carton check there is no transportation damage before using the projector.
Should there be any damage caused by transportation, consult your dealer and do not use the apparatus.
The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture,
excessive heat, humidity and dust. Do not allow contact with water or any other liquids.
The projector is not designed or intended to be mounted directly on to inflammable surfaces.
The projector is only intended for installation, operation and maintenance by qualified personnel.
The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent wall surfaces. Be sure
that no ventilation slots are blocked.
Do not project the beam onto inflammable surfaces, minimum distance is 5m. 5m
Avoid direct exposure to the light from the lamp. The light is harmful to the eye.
Do not attempt to dismantle and/or modify the projector in any way.
Electrical connection must only be carried out by qualified personnel.
Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector.
It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.
Do not connect this device to any other types of dimmer apparatus.
Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cord come into contact
with other cables. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.
Keep the lamp clean. Do not touch the lamp glass with bare hand.
The projector should always be installed with a secondary safety fixing. A safety cord is supplied for this; it should be
attached as shown in “installing the projector” section.
The lamp used in this projector is a discharge lamp. After switching off don’t attempt to restart the projector until lamp has
cooled, this will require approx 15 minutes. Switching the lamp on and off at short intervals will reduce the life of both the
lamp and the projector. But occasional breaks will prolong the life of the lamp and projector.
Never run the projector without a lamp.
There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the
covers removed.
Always disconnect from the mains, when the device is not in use or before cleaning it or
before attempting any maintenance work !
If you have any questions, don’t hesitate to consult your dealer or manufacturer.

4/22
INSTALL THE PROJECTOR
(2PCS)
(2PCS)
HANDLES
(2PCS)
SAFETY CORD
CLAMPS
To pass 2 SAFETY CORDS
through 4 HOLES for safety!
WARNING
257
106
Take 2 clamps and 2 safety cords out from the package and mount 2 clamps on the underside of fixture with 4 retainers
attached to each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the
WARNING on the underside of the base as shown above) To pass 2 SAFETY CORDS through 4 HOLES for safety!
Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning. Always ensure that
the structure that you are going to mount the projector is secure and is strong enough to support a weight of XL WASH
1500.
WARNING:
1. Unlock the PAN and TILT before the 1st application of projector for safety.
2. The projector MUST be lifted or carried by the HANDLES instead of clamps.
3. For safety the safety cord should afford 10 times of the unit’s weight.
FITTING THE LAMP
NUT
LAMP REFLECTER
Lock the yoke before fitting/replacing the lamp.
Loosen 4 screws and open the back covers, you can see the structure as shown in the figure above.
Loosen 2 nuts at the both ends of lamp and take out the worn-out lamp. Suggest to free one end after another.
Fit new lamp and fasten 2 screws at the both ends of lamp. Note: don’t touch the bulb of the new lamp with bare hand so
as not to influence the beam output; the PST (pumping stem tip off) on the bulb facing the rear cover with fans
perpendicularly and being not in the beam’s way is a must and aids cooling.
Close the rear cover and fasten 4 screws.
NOTE: The convex of the nuts should face to the side when fitting the lamp.
WARNING: The MSR series are high-pressure lamps with external igniters ( ). Care should always be taken
when handling these lamps.Always read the manufacturers "Instructions for use" enclosed with the lamp.

5/22
POWER SUPPLY-MAINS
Connect the power cord as follows:
L (live) =brown
E (earth) =yellow/green
N (neutral) =blue
Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked
on the panel of the projector. It is recommended that each projector be supplied separately so that they may be
individually switched on and off.
IMPORTANT
It is essential that each projector is correctly earthed and the electrical installation conforms to all relevant
standards.
CONTROL CONNECTION
Connection between controller and projector and between one projector and another must be made with a 2
core-screened cable, with each core having at least a 0.5mm diameter. Connection to and from the projector is via
cannon 3 pin (which are included with the projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown
in the figure above.
Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of
the plug is not connected in any way. The XL WASH 1500 accepts digital control signals in protocol DMX512 (1990).
Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input
and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown
in the figure below.
DMX OUTDMX IN
DMX IN FROM TERMINATER
DMX IN DMX OUT DMX IN DMX OUT
CONTROLLER

6/22
DMX TERMINATOR
In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This
prevents electrical noise from disturbing and corrupting the DMX control signals.
The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2 and 3, which is
then plugged into the output socket on the last projector in the chain. The connections are illustrated below.
21
3
120
DMX TERMINATOR
CONNECTION
Connect a 120 (OHM) resistor
across pins 2 and 3 in an XLR plug
and insert into the DMX out socket
on the last unit in the chain.
PIN 3
PIN 2
SETUP OPTIONS-PROJECTOR CONFIGURATION
UP
UP
CODER BUTTON
Projector configuration can be set conveniently via pressbutton switch and LCD display. Turn the projector on and the
LCD display will show DMX address you set and save last time and it can be reset and saved again as you please.
Launch the projector. Press button ENTER more than 5 seconds to unlock panel.
Press button UP or DOWN if you want to browse through the various Setup Options. There are 8 option codes from
DMX Address to Lamp Manual Control, and each code has a specific function. If you turn the coder knob
clockwise, the function like as button UP . On the contrary, the function like as button DOWN .
Press button ENTER to save your settings or enter the next menu. There is same function if you push the coder knob.
Press button UP or DOWN to shift.
Press button FUNC, it will return to the upper menu one by one. If you stay for minutes defaulted will show display status
automatically.
TO SET THE DMX START ADDRESS
Each XL WASH 1500 must be given a DMX start address so that the correct projector responds to the correct control
signals. This DMX start address is the channel number from which the projector starts to “listen” to the digital control
information being sent out from the controller. The XL WASH 1500 has 3 DMX modes. There are standard mode,
extended mode and short mode. For example standard mode has 17 channels, so set the No. 1 projector’s address 001,
No. 2 projector’s address 018, No. 3 projector’s address 035, No. 4 projector’s address 052, and so on.
Launch the projector. Press button ENTER or coder knob more than 5 seconds to unlock panel.
Press button FUNC to display DMX address;
Press button UP and DOWN, you can set the address;
Press button ENTER to confirm; In the same time. The GREEN LED will flash one time. It means the setting has
been enabled.
Press button FUNC, it will return to the upper menu one by one.

7/22
OPERATION MENU
1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL
PR LIGHTING
XL SERIES
XL 1500 WASH
DMX Address=001
DMX Address
DMX Addres
s
001-499 in short mode
001-496 in stand mode
001-49
0
in extended mod
e
Reset Rese
t
Are You Sure?
Config Settings
DMX Mode
DMX Mod
e
Standard 1
6
DMX Mod
e
Extended 16
DMX Mod
e
Short
8
Lamp Control
Lamp Control B
y
Control Channel
Lamp Control B
y
Power On
Lamp Control B
y
DMX Presen
t
Loss of DMX
When DMX is Los
t
Normal Time Ou
t
When DMX is Los
t
Hold Last Valu
e
Factory Settings
(Press button
DOWN/UP/ENTER at the same
time to enter the sub-menu)
Fixture type
(WARNING：Never change
the fixture type or the
system will be damaged!)
Fixture type=
XL 120
0
Fixture type=
XL 70
0
Fixture type=
XL 57
5
Fixture type=
XL 120
0
F
S
Fixture type=
XL 120
0
Wash
Fixture type=
XL 700 Wash
Fixture type=
XL 180
0
Fixture type=
XL 150
0
Fixtur
e
type=
XL 1500 Wash
Fixture type=
X
S 120
0
Option Settings
Colour Positions
Colou
r
Position
s
STEPPED
Colou
r
Position
s
LINEA
R
Pan DMX Invert
Pan DMX Inver
t
OFF
Pan DMX Inver
t
ON
Tilt DMX Invert
Tilt DMX Inver
t
OFF
Tilt DMX Inver
t
ON
Pan Tilt Swap
Pan Tilt Swa
p
OFF
Pan Tilt Swa
p
ON
Dimmer Invert
Dimmer Inver
t
OFF
Dimmer Inver
t
ON
Zoom Invert
Zoom Inver
t
OFF
Zoom Invert

8/22
ON
CMY Invert
CM
Y
Inver
t
OFF
CM
Y
Inver
t
ON
CTO Invert
C
TO Inver
t
OFF
C
TO Inver
t
ON
Defaults
Default
s
OFF
Default
s
Restore Default
s
Display Options
Display Mode
Displa
y
On Alwa
ys
Displa
y
Off After Dela
y
Display Invert
Displa
y
Inver
t
OFF
Displa
y
Inver
t
ON
Display Dimming
Disp Dim Level
Min
Disp Dim Level
1
Dis
p
Dim Level
2
Disp Dim Level
3
Disp Dim Level
4
Disp Dim Level
5
Disp Dim Level
6
Disp Dim Level
7
Disp Dim Level
8
Disp Dim Level
9
Disp Dim Level
Full
Display Contrast Display Contras
t
XXX
(
1~36, Defaul
t
is 16
)
Display Language
Language =
En
g
lish
Language =
Chines
e
Information
Lamp Hours Lamp Hours =
X
X
Reset Lamp Hour
s
Are You Sure?
Total Hours Total Hours =
X
X
Temperature
Display Board Display Board =
X
X
℃
Driver Board 1 Driver Board 1 =
X
X
℃
Driver Board 2 Driver Board 2 =
X
X
℃
Pan and Tilt Pan and Tilt =
X
X
℃
Head Sensor Head Sensor=
X
X
℃
Software Version
Display Board Display Board =
X.X.
X
Driver Board 1 Driver Board 1 =
X.X.
X
Driver Board 2 Driver Board 2 =
X.X.
X
Pan and Tilt Pan and Tilt =
X.X.
X
Power Board Power Board =
X.X.
X
View DMX values DMX Channel
1=
0

9/22
Test Modes
Factory Setup
Factory Setu
p
OFF
Factory Setu
p
ON
Self Test
Self Tes
t
OFF
self tes
t
ON
Lamp Manual
Control
Lamp Status Status = XX
X
Control =
X
Turn Lamp On
Turn Lamp Off

10/22
ERROR MESSAGES
In the course of launch, XL WASH 1500 examines automatically whether there are errors and if there are, it will display
information as follows:
Display Message
Sensor Err S1-M1 Colour wheel 1 (1# drive board motor 1) error
Sensor Err S1-M2 CTO (1# drive board motor 2) error
Sensor Err S1-M3 CYM-cyan (1# drive board motor 3) error
Sensor Err S1-M4 CYM-yellow (1# drive board motor 4) error
Sensor Err S1-M5 CYM-magenta (1# drive board motor 5) error
Sensor Err S1-M6 Dimmer (1# drive board motor 6) error
Sensor Err S2-M1 Zoom (2# drive board motor 1) error
Sensor Err S2-M2 Inside lens 1 (2# drive board motor 2) error
Sensor Err S2-M3 Inside lens 2 (2# drive board motor 3) error
Sensor Err S2-M4 Colour wheel 2 (2# drive board motor 4) error
Sensor Err S2-M5 Strobe 1 (2# drive board motor 5) error
Sensor Err S2-M6 Strobe 2 (2# drive board motor 6) error

11/22
DMX PROTOCOL
Short
mode Standard mode Extended mode FUNCTION DMX DESCRIPTION
1 1 1 Strobe
000-010 Black
011-025 Open
026-225 Strobe speed from slow to fast
226-255 Open
2 2 2 Dimmer
000-007 Black
008-255 Dimming from dark to light (0-100%)
3 Dimmer Fine 000-255 Dimmer in 16 Bit precision
3 3 4 CYM Macro
000-01
6
White
01
7
-03
5
Yellow+ Magenta=Red
03
6
-054 Yellow
05
5
-07
3
Yellow+ Cyan=Green
074-092 Cyan
09
3
-110 Cyan+ Magenta=Blue
111-12
8
Magenta
12
9
-25
5
CYM colour mixing from slow to fas
t
4 4 5 CYM-Cyan 000-255 Cyan (Linear 0-100%)
6
CYM-Cyan
Fine 000-255 Cyan in 16 Bit precision
5 5 7 CYM-Yellow 000-255 Yellow (Linear 0-100%)
8
CYM-Yellow
Fine 000-255 Yellow in 16 Bit precision
6 6 9 CYM-Magenta 000-255 Magenta (Linear 0-100%)
10
CYM-Magenta
Fine 000-255 Magenta in 16 Bit precision
7 7 11 CTO 000-255 Linear adjust from high to low
12 CTO Fine 000-255 CTO in 16 Bit precision
8 8 13 Colour Wheel 1
000-01
6
White
017-024 White/colour 1
025-032 Colour 1
033-040 Colour 1/colour 2
041-048 Colour 2
049-056 Colour 2/colour 3
057-064 Colour 3
065-072 Colour 3/colour 4
073-080 Colour 4
081-088 Colour 4/colour 5
089-096 Colour 5
097-104 Colour 5/colour 6
105-112 Colour 6
113-120 Colour 6/ white
121-127 white
128-133 Rainbow rotation speed 1 (slowest)
134-139 Rainbow rotation speed 2

12/22
140-145 Rainbow rotation speed 3
146-151 Rainbow rotation speed 4
152-157 Rainbow rotation speed 5
158-163 Rainbow rotation speed 6
164-169 Rainbow rotation speed 7
170-175 Rainbow rotation speed 8
176-181 Rainbow rotation speed 9
182-187 Rainbow rotation speed 10
188-195 Stop in current position
196-201 Rainbow reverse rotation speed
1(slowest)
202-207 Rainbow reverse rotation speed 2
208-213 Rainbow reverse rotation speed 3
214-219 Rainbow reverse rotation speed 4
220-225 Rainbow reverse rotation speed 5
226-231 Rainbow reverse rotation speed 6
232-237 Rainbow reverse rotation speed 7
238-243 Rainbow reverse rotation speed 8
244-249 Rainbow reverse rotation speed 9
250-255 Rainbow reverse rotation speed 10
9 9 14 Colour Wheel 2
000-016 White
017-024 White/colour 1
025-032 Colour 1
033-040 Colour 1/colour 2
041-048 Colour 2
049-056 Colour 2/colour 3
057-064 Colour 3
065-072 Colour 3/colour 4
073-080 Colour 4
081-088 Colour 4/colour 5
089-096 Colour 5
097-104 Colour 5/colour 6
105-112 Colour 6
113-120 Colour 6/ white
121-127 white
128-133 Rainbow rotation speed 1 (slowest)
134-139 Rainbow rotation speed 2
140-145 Rainbow rotation speed 3
146-151 Rainbow rotation speed 4
152-157 Rainbow rotation speed 5
158-163 Rainbow rotation speed 6
164-169 Rainbow rotation speed 7
170-175 Rainbow rotation speed 8
176-181 Rainbow rotation speed 9
182-187 Rainbow rotation speed 10

13/22
188-195 Stop in current position
196-201 Rainbow reverse rotation speed
1(slowest)
202-207 Rainbow reverse rotation speed 2
208-213 Rainbow reverse rotation speed 3
214-219 Rainbow reverse rotation speed 4
220-225 Rainbow reverse rotation speed 5
226-231 Rainbow reverse rotation speed 6
232-237 Rainbow reverse rotation speed 7
238-243 Rainbow reverse rotation speed 8
244-249 Rainbow reverse rotation speed 9
250-255 Rainbow reverse rotation speed 10
10 10 15 Zoom
The DMX value of narrow angle channel is 0
000-255 Linear adjust from 15° to 42°
The DMX value of narrow angle channel is not 0
000-009 Narrow angle mode
010-255 Linear adjust from 15° to 42°
16 Zoom Fine 000-255 Zoom in 16 precision
11 11 17 Narrow Angle
This channel is available only with DMX value of zoom
channel is between 000-009
000-255 Open the inside Zoom lens, change
beam angle to 10°
12 12 1
8
Pan 000-25
5
Pan rotation 450°
1
3
1
9
Pan Fine 000-25
5
Pan rotation in 16 precision
1
3
14 20 Til
t
000-25
5
Tilt rotation 270°
1
5
21 Tilt Fine 000-2
5
5
Tilt rotation in 16 precision
16 22
Pan & Tilt
speed 000-255 Pan&Tilt speed from fast to slow
14 17 23 Control
000-04
8
Reserved
04
9
-080 Rese
t
081-112 Reserved
11
3
-144 Lamp off ( stop in DMX value for 10 s)
14
5
-16
8
Reserved
16
9
-200 Lamp power reduced to 50%
201-22
3
Reserved
224-25
5
Lamp on (See remark below)
Remark:
If you intend to turn on/off the lamp via the last channel of the controller, don’t attempt to push the channel to value
224-255 immediately after turning it off, or push the slide bar to value 224-255 to wait it cooling. Under these 2
circumstances, the lamp can not be turned on. The right operation is: turn it off---cool down---push the slide bar to turn it
on.

14/22
LED INDICATION
Green
On DMX signal OK
Off No DMX signal
Flash DMX signal error
Yellow On
Setting the panel
Blue On Power
Red/Green Red Running self test mode
Green Reserved
MAINTENANCE
If the projector’s lens becomes damaged or broken it should be replaced. If the lamp becomes damaged or deformed in
any way it must be replaced. If the light from the lamp appears dim this would normally indicate that it is reaching the end
of its life and it should be changed at once, aged lamps run to the extremity of their life might explode. If the projector
does not function, check the fuses on the power socket of the projector, they should only be replaced by fuses of the
same specification. Should these be damaged call a qualified technician before replacement. The projector has thermal
protection device that will switch off the projector in case of overheating, should either of these operate, check that the
fans are not blocked, and if they are dirty clean them before switching on the projector again. Check that the fans are
operational, if not call a qualified technician.
Any maintenancework should only be carried out by qualified technicians.
LUBRICATION
To ensure the smooth motion of the inside Zoom lens, it is recommended that the shafts for the Zoom lens holder be
lubricated periodically, preferably every two months. Use only high quality, high-temperature resistant grease instead of
any type of oil.
KEEPING THE PROJECTOR CLEAN
To ensure the reliability of the projector it should be kept clean. It is recommended that the fans should be cleaned every
15 days. The lens and dichroic colour filters should also be regularly cleaned to maintain an optimum light output. Do
NOT use any type of solvent on dichroic colour filters.
Cleaning frequency depends on the environment in which the fixture operates: damp, smoke or particularly dirty
surroundings can cause greater accumulation of dirt on the unit’s optics. A soft cloth and typical glass cleaning products
should be used in cleaning. It is recommended to clean the external optics at least once every 20 days and clean the
internal optics at least once every 30 / 60 days.
Do not use any organic solvent, e.g. alcohol, to clean the reflector mirror, dichroic colour filters or housing of
the apparatus.

15/22
TROUBLESHOOTING
PROBLEM ACTION
The projector doesn’t switch on
¾Check the fuse on the power socket.
¾Replace the lamp.
The lamp comes on but the projector
doesn’t respond to the controller
¾Make sure that the projector is correctly configurated.
¾Replace or repair the DMX cable.
The projector only functions intermittently ¾Make sure the fan is working and not dirty.
Defective projection
¾Check the lenses are not broken.
¾Remove dust or grease from the lenses.
The project image appears to have a halo
¾Make sure the lamp is installed correctly.
¾Carefully clean the optical group lenses and the projector
components.
The beam appears dim
¾Check the optics is clean.
¾Replace with a new lamp of the specified type and rating.

16/22
TECHNICALDATA
VOLTAGES:
Electronical ballest(PR-2805): 200/220/230/240VAC，50/60Hz
Options:
Magenetic ballest(PR-2805M):
100/120VAC，50/60Hz
220VAC ，50/60Hz
Options: 200/230/240VAC，50/60Hz
POWER CONSUMPTION:
Electronical ballest(PR-2805): 1700W@220V
Magenetic ballest(PR-2805M): 1800W@220V
LAMP:
OSRAM HTI 1500 W/D7/60
Colour Temperature 6000°K
Socket SFc10-4，double ended
Manufacturers Rated Lamp Life 750 Hours replacement
Or
PHILIPS MSRGold1510SADE
Colour Temperature 5800°K
Socket SFc10-4，double ended
Manufacturers Rated Lamp Life 750 Hours replacement
COLOURS:
Smooth CYM colour mixing system with macros
2 wheels each with 6 dichroic colour filters plus white and CYM colour mixing system
With variable speed bi-directional rainbow effect
Step/linear colour changing is available
COLOUR TEMPERATURE CORRECTION:
Linearly colour temperature correction
FOCUS:
DMX controlled focus
DIMMER:
0-100% linearly adjustable
SHUTTER:
Double shutter blades, 0.3~12 F.P.S
Macros

17/22
HEAD MOVEMENT:
Pan 450º, Tilt 270º with auto position correction
BEAMANGLE:
10°narrow angle mode
15°～42°
CONTROL:
DMX512, 3 pin, 5 pin interfaces
14 channels in short mode, 17 channels in standard mode, and 23 channels in extended mode.
Self-test mode
OTHER FUNCTIONS:
Adjustable Pan & Tilt speed
Fixture and lamp usage time display
LCD display with English and Chinese language menu
Energy saving function of the ballast
Built-in analyzer for easy fault finding, error messages
Built-in demo sequences
Setup options by chargeable battery inside without power connection.
Input signal isolating protection
Network interface (Reserved)
HOUSING:
Composite plastic, IP20
WEIGHT:
Electronical ballest(PR-2805): 32kg
Magenetic ballest(PR-2805M): 45kg

18/22
SIZES:
See at below
548
755
448
238
453
535
505
LIGHT OUTPUT:
3430
1520
270
4.43
6.63
18.57
25
430
2380
1700
9730
760
4230
953021440 5360
20
14.85
5.30
3.55
10
7.43
2.65
1.77
11.44
15
2.66
3.98
42°（lux）
15°（lux）
20m
4m
12m
4m
12m
16m
0m
8m
8m
10°（lux）
20m
0
0
0
0
DISTANCE (m)
10° DIAMETER (m)
16m
3.71
1.33
5
0.89
6830
38120
85770
10° 15° 42°
15° DIAMETER (m)
42° DIAMETER (m)

SENS1
SENS2
SENS3
SENS4
SENS5
SENS6
MOTOR1 MOTOR2 MOTOR3 MOTOR4 MOTOR5 MOTOR6
SLAVE #1 PCB
SENS1
SENS2
SENS3
SENS4
SENS5
SENS6
MOTOR1 MOTOR2 MOTOR3 MOTOR4 MOTOR5 MOTOR6
SLAVE #2 PCB
PAN & TILT PCB
GND
GND
VCC
VCC
DMX-SENS1
DMX-SENS2
GND
GND
VCC
VCC
DMX-SENS1
DMX-SENS2
+
-
TILT ENCODE
+
-
PAN ENCODE
3
12
DMX-IN DMX-OUT
12 3
1
23
4
51
2
3
4
5
DMX-IN DMX-OUT
VGS VGS VGS
VGS VGSVGS VGS VGS VGS
VGSVGS VGS
HALL 1-5
View of mark side HALL 1-3 View of mark side
HALL 1-1
View of mark side
HALL 1-4
View of mark side
HALL 2-1
View of mark side
HALL 2-4
View of mark side
PAN TILT
GND GND VCC VCC DMX-SENS1 DMX-SENS2
V
G
S
V
G
V
G
S
V
G
S2
S1 S1 S2
HALL 1-2
View of mark side
LED1 LED2LED3
LED4
LCD DISPLAY
FUNCTION DOWN UP ENTER
GND
GND
VCC
VCC
DMX-SENS1
DMX-SENS2
GND
DATA-
DATA+
FEMALE FEMALEMALEMALE
DC6V
GND
+-
Battery
View side of no axletree
M2-6
STROBE 2
A B C D
A B C D
View side of no axletree
M2-5
STROBE 1
A B C D
A B C D
View side of no axletree
M2-4
COLOUR 2
A B C D
A B C D
View side of no axletree
M2-3
Inside Fresnel Lens 2
A B C D
A B C D
View side of no axletree
M2-2
Inside Fresnel Lens 1
A B C D
A B C D
View side of no axletree
M2-1
Fresnel Lens Focus
A B C D
A B C D
View side of no axletree
M1-6B
DIMMER-2
A B C D
A B C D
View side of no axletree
M1-5
MAGENTA
A B C D
A B C D
View side of no axletree
M1-4
YELLOW
A B C D
A B C D
View side of no axletree
M1-3
CYAN
A B C D
A B C D
View side of no axletree
M1-1
COLOUR1
A B C D
A B C D
View side of no axletree
M1-2
CTO
A B C D
A B C D
View side of no axletree
J1
PAN
A B C D
A B C D
View side of no axletree
J2
TILT
A B C D
A B C D
View side of no axletree
M1-6A
DIMMER-1
A B C D
A B C D
Filter
Thermostat
GND
GND
DMX-SENS1
DMX-SENS2
+-
FAN1
FAN2
FAN3
FAN4
DC
FAN & LIGHTING PCB
GG FULL
FULL
3 / 4
HALF
S S G V
V S G
S S G V
HEAD FAN 1 HEAD FAN n
BOX FAN
HEAD FAN 1 HEAD FAN n
GV
GV
GV
GV
AC INPUT
NL E
SWITCH
Fuse
TRANSFORMER
ELECTRONIC G
G
+24V
+24V
FG
ACL
ACN
G
+24V
SW-PB
VCC
VCC
IGNITOR
GROUND L N TO IGNITOR
ELECTRONIC
BALLAST
LAMP
162345

SENS1
SENS2
SENS3
SENS4
SENS5
SENS6
MOTOR1 MOTOR2 MOTOR3 MOTOR4 MOTOR5 MOTOR6
SLAVE #1 PCB
SENS1
SENS2
SENS3
SENS4
SENS5
SENS6
MOTOR1 MOTOR2 MOTOR3 MOTOR4 MOTOR5 MOTOR6
SLAVE #2 PCB
PAN & TILT PCB
GND
GND
VCC
VCC
DMX-SENS1
DMX-SENS2
GND
GND
VCC
VCC
DMX-SENS1
DMX-SENS2
+
-
TILT ENCODE
+
-
PAN ENCODE
3
12
DMX-IN DMX-OUT
12 3
1
23
4
51
2
3
4
5
DMX-IN DMX-OUT
VGS VGS VGS
VGS VGSVGS VGS VGS VGS
VGSVGS VGS
HALL 1-5
View of mark side HALL 1-3 View of mark side
HALL 1-1
View of mark side
HALL 1-4
View of mark side
HALL 2-1
View of mark side
HALL 2-4
View of mark side
PAN TILT
GND GND VCC VCC DMX-SENS1 DMX-SENS2
V
G
S
V
G
V
G
S
V
G
S2
S1 S1 S2
HALL 1-2
View of mark side
LED1 LED2LED3
LED4
LCD DISPLAY
FUNCTION DOWN UP ENTER
GND
GND
VCC
VCC
DMX-SENS1
DMX-SENS2
GND
DATA-
DATA+
FEMALE FEMALEMALEMALE
DC6V
GND
+-
Battery
View side of no axletree
M2-6
STROBE 2
A B C D
A B C D
View side of no axletree
M2-5
STROBE 1
A B C D
A B C D
View side of no axletree
M2-4
COLOUR 2
A B C D
A B C D
View side of no axletree
M2-3
Inside Fresnel Lens 2
A B C D
A B C D
View side of no axletree
M2-2
Inside Fresnel Lens 1
A B C D
A B C D
View side of no axletree
M2-1
Fresnel Lens Focus
A B C D
A B C D
View side of no axletree
M1-6B
DIMMER
A B C D
A B C D
View side of no axletree
M1-5
MAGENTA
A B C D
A B C D
View side of no axletree
M1-4
YELLOW
A B C D
A B C D
View side of no axletree
M1-3
CYAN
A B C D
A B C D
View side of no axletree
M1-1
COLOUR1
A B C D
A B C D
View side of no axletree
M1-2
CTO
A B C D
A B C D
View side of no axletree
J1
PAN
A B C D
A B C D
View side of no axletree
J2
TILT
A B C D
A B C D
View side of no axletree
M1-6A
DIMMER
A B C D
A B C D
螺纹镜调焦
降色温片
S S G V
V S G
S S G V
AC INPUT
N
L
Filter E
HEAD FAN n
HEAD FAN 1
SWITCH
LAMP
Thermostat
GND
GND
DMX-SENS1
DMX-SENS2
-
+FAN1
FAN2
FAN3
FAN4
DC
LN
AC230V IGNITER CAPACITORBALLAST
Cap-1 Cap-2
D
N
L
GND
50Hz
60Hz
LOW Ballast
Ph
FAN & LIGHTING PCB
VCC
VCC FULL
FULL
3 / 4
HALF
PPLHND CCHL
CN6
Thermostat
50Hz
60Hz
HIGH Ballast
Ph
PCB FAN
BOX FAN
TRANSFORMER
ELECTRONIC
G
G
+24V
+24V
FG
ACL
ACN
G
+24V
SW-PB
GND
GND
GND
FUSE
DC-SEL