Ruijie RG-RSR10-02E Series Installation and operating manual

RG-RSR10-02E Series Routers
Hardware Installation and Reference Guide 1.20

Copyright statement
Ruijie Networks©2000-2014
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup,
modification, transmission, translation or commercial use of this document or any portion of this document,
in any form or by any means, without the prior written consent of Ruijie Networks is prohibited.
, , , ,
, ,
, , ,
, , are registered trademarks of Ruijie
Networks. Counterfeit is strictly prohibited.
Exemption statement
This document is provided “as is”. The contents of this document are subject to change without any notice.
Please obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to
ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to
content omissions, inaccuracies or errors.

Preface
Thank you for using our products. This manual will guide you through the installation of the router.
Scope
It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it
is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks website: http://www.ruijienetworks.com/
Online customer services: http://webchat.ruijie.com.cn
Customer service center: http://www.ruijie.com.cn/service.aspx
Customer services hotline: [phone]
BBS: http://support.ruijie.com.cn
Customer services email: [email protected]
Related Documents
Documents Description
Configuration Guide Describes network protocols and related mechanisms that supported by the
product, with configuration examples.
Command Reference Describes the related configuration commands, including command modes,
parameter descriptions, usage guides, and related examples.
Documentation Conventions
The symbols used in this document are described as below:
This symbol brings your attention to some helpful suggestions and references.
This symbol means that you must be extremely careful not to do some things that may damage the device or
cause data loss.

Chapter 1 Product Overview
The Ruijie 10-02E series Reliable multi-Service Router (RSR) is a proprietary data communications product developed
with advanced semiconductor and communication & control technologies. The RSR10-02E series routers are in
compliance with international standards and are interoperable with mainstream routers both in operation and configuration
methods. If you are familiar with configuration commands of mainstream routers, you may read this manual without any
prior training.
About the RG-RSR10-02E
The RSR10-02E modular router is an enterprise-class networking product integrating a high-performance 32-bit Reduced
Instruction Set Computing (RISC) microprocessor. The router is based on Ruijie RGOS operating system that provides an
industry-standard command line interface. The router integrates routing, switching, voice, security, transmission and video,
and satisfies personalized requirements in various application environments. The router also provides rich software
features such as Voice over Internet Protocol (VoIP), Virtual Private Network (VPN), Internet Protocol Version 6 (IPv6),
Multicast VPN Routing & Forwarding (MVRF), Multi-Protocol Label Switching (MPLS), multicasting as well as backup
schemes and Quality of Service (QoS) features. The features are applied to solutions of access services such as data,
video and voice. These features enable a three-network-in-one solution for small and medium enterprises.
The RSR10-02E modular router supports up to two optional Smart Interface Cards (SIC).
Different SIC slots support different SIC cards. For your convenience, each slot is marked with the supported SIC types.
There are five types of SIC cards in total. See Table 1-1.
Table 1-1 SIC Cards Supported by the RSR10-02E Router
Type Supported SIC Cards
A SIC-8A, SIC-1B-U, SIC-1B-S/T, SIC-2FXS,SIC-2FXO,SIC-SEC encrypted key
B SIC-1HS, SIC-3G-TD,SIC-3G-CDMA,SIC-3G-WCDMA
C SIC-1CE1, SIC-1E1-F
D N/A
E SIC-3G-CDMA-E, SIC-3G-WCDMA-E, SIC-3G-WCDMA-H-E
Table 1-2 SIC Types Supported by Each SIC Slot on the RSR10-02E Router
Type A Type B Type C Type D Type E
Slot 2 Supported Supported Supported Not Supported Supported
Slot 3 Supported Supported Supported Not Supported Supported
The entire device supports one SIC-SEC with the key encryption function in any slot.

For your convenience, each slot is marked with the supported SIC types. For example, in Figure 1-1, SIC SLOT 3
supports Type A, Type B, Type C, and Type E SIC cards. SIC SLOT 2 supports Type A, Type B, Type C and Type E SIC
cards.
Figure 1-1 SIC Types Marked Above the SIC SLOT 3 and SLOT 2
Figure 1-2 Part of Back Panel of the RSR10-02E Series Routers
Technical Specifications
Table 1-3 Technical Specifications of the RSR10-02E Router
Model RSR10-02E
Interfaces
1 Console port
1 AUX port
1 USB interface
1 SD card interface
1 FUNC button
8 10/100 Mbps Ethernet ports
2 Gigabit Ethernet ports
SIC Slots 2
Note: You can configure up to two SIC modules as required.
Processor RISC
BOOT ROM 2 MB
NAND FLASH 128 MB
DDR II 512 MB
Input Voltage 100 VAC to 240 VAC, 50 Hz to 60 Hz

Power Consumption Less than 25 W
Operating
Temperature 0°C to 45°C
Storage Temperature -40°C to 70°C
Operating Humidity 10% to 95% RH
Dimensions
(W x H x D) 288 mm x 44 mm x 204 mm
Product Features
Access density and processing capacity
The two SIC slots support up to 2 non-channelized E1 interfaces, 2 ISDN U or S/T interfaces, 2 synchronous serial
interfaces, or 16 asynchronous serial interfaces, 2 3G networks to provide a high-density solution for remote office. The
router has 8 fast Ethernet ports, and 2 Gigabit Ethernet ports. It offers a FUNC button to upgrade the RGOS operating
system from an SD card or USB stick to the router. The E1 interface complies with ITU-T G.703, the ISDN U interface
complies with ITU-T G.961 ANSI T1.601, and the ISDN S/T interface complies with ITU-T I.430. The synchronous serial
interface can connect to the Digital Divide Network (DDN), frame relay, and X.25 networks. These features make the
router an ideal access router for medium- and large-sized branches.
Reliability
The router adopts backup center technologies, which greatly improves network reliability. Various backup modes are
available for high reliability requirements.
Compatibility
The router is fully compatible with devices from other vendors.
Power supply
By using high-quality standard power supplies, the router provides protection against surge, overvoltage, undervoltage,
overcurrent to deliver stable and reliable output. In addition, it supports transient power interruption protection.
Construction
With the rack mount 1U chassis with EMI shielding, the router is highly resistant to shock, high/low temperature, and
electromagnetic radiation, and works stably.
Certificate
The router has passed the network access license (NAL) testing by the Ministry of Information Industry (MII), P.R. China.
Product Images
Front Panel
Figure 1-3 Front Panel of the RSR10-02E Router

Note: 1: FE1/0 to FE1/7 indicator
2: FE1/0 to FE1/7 port
3: GE0/0 to GE0/1 port
4: GE0/0 to GE0/1 port indicator
5: Console port
6: Aux ports
7: SD card interface
8: SD indicator
9: USB interface
10: FUN button
11: PWR indicator, SYS indicator, USB indicator
12: Ruijie Networks RSR10 Series logo
LED Indicators
Table 1-4 LED Indicators on the RSR10-02E Router
Indicator Status Meaning
SYS
Off The router is not receiving power.
Blinking green The router starts up.
Solid green The router is operational.
Solid red The router is not working properly.
PWR Off Power off.
Solid green Power on.
SD
Off SD card is not present.
Green on SD card is connected to the device and is recognized.
Blinking green SD card is receiving or transmitting data.
Solid red or blinking red SD card is not working properly.
USB
Green on USB device is connected to the device and is recognized.
Blinking green USB device is receiving or transmitting data.
FE Port
Off No link.
Solid green FE port link up at 10/100 Mbps.
Blinking green FE port link up at 10/100 Mbps, and is receiving or transmitting data.

GE Port
Off No link.
Solid green GE port link up at 1000 Mbps
Blinking green GE port link up at 1000 Mbps, and is receiving or transmitting data.
Solid yellow GE port link up at 10/100 Mbps.
Blinking yellow GE port link up at 10/100 Mbps, and is receiving or transmitting data.
Back Panel
Figure 1-4 Back Panel of the RSR10-02E Router
Note: 1: SLOT 3
2: SLOT 2
3: Power switch
4: Power receptacle
5: Chassis ground connector
If you cannot determine which slot is occupied by the current module, you can run the show slots command
in privileged EXE mode to view the slot number in router version information
About Fixed Ports
This section describes fixed ports on the RSR10-02E series router.
Console Port and Auxiliary Port
Features
The RSR10-02E series router provides one console port and one AUX port.
Table 1-5 Specifications of the Console port
Index Parameter
Interface Standard EIA/TIA-RS232
Connector RJ-45
Rate Supports 9600 to 115200 bps baud rates. The configurable frequency points are 9600, 57600

and 115200 bps. The default is 9600 bps.
Table 1-6 Specifications of the AUX port
Index Parameter
Interface Standard EIA/TIA-RS232
Connector RJ-45
Rate Supports 9600 to 115200 bps baud rates. The configurable frequency points are 9600,
19200, 38400, 57600 and 115200 bps. The default is 9600 bps.
Cables
Serial cables are supplied with the RSR10-02E router.
FE Ports
Port Image and LED Indicators
The following figure shows the fixed FE ports and its corresponding Link/ACT LED indicators.
Figure 1-5 FE Ports and Corresponding LED Indicators
For descriptions of FE port Link/ACT LED indicators, see the “LED Indicators” section in Chapter 1.
An RSR10-02E series router provides eight fixed 10/100 Mbps Ethernet ports.
The following table describes the basic features of the Ethernet ports.
Table 1-7 Specifications of the FE ports
Protocol IEEE Std 802.3-2008
Quantity 8
Interface Type 10Base-T/100Base-TX interface
Cables
All FE ports use Category 5 unshielded twisted pair (UTP) RJ-45 cables.
Straight-through cable: All wire pairs are in the same order on each end of the RJ-45 cable. The straight-through cable
is used to connect a terminal device such as a PC or router to a hub or LAN switch.

Crossover cable: Pin 1 and pin 2 at one end of the cable correspond to pin 3 and pin 6 at the other end, respectively. The
crossover cable is used to connect two terminal devices, such as connecting a PC to a PC, and connecting a router to a
router.
If the port supports Auto-MDI/MDIX, both straight-through and crossover cables can be used.
Considering that you may customize cables, the following section describes how to wire straight-through and crossover
cables.
As shown in the following figure, the pins of the RJ-45 connector are numbered 1 to 8, counting from left to right when the
connector is viewed from the side without the latching tab.
Figure 1-6 RJ-45 Connector Pin Number
For a straight-through cable, use the same wiring.
Figure 1-7 Straight-through Wiring Diagram
For a crossover cable, swap the positions of the two pairs.
Figure 1-8 Crossover Wiring Diagram

Table 1-8 Crossover Cable Pinouts
RJ45 Pin #
End 1 Signal Color RJ45 Pin # End 2 Signal Color
1 TX+ White-green 1 TX+ White-orange
2 TX- Green 2 TX- Orange
3 RX+ White-orange 3 RX+ White-green
6 RX- Orange 6 RX- Green
GE Ports
Port Image and LED Indicators
The following figure shows the fixed GE ports and its corresponding Link/ACT LED indicators.
Figure 1-9 GE Ports and Corresponding LED Indicators
For descriptions of GE port Link/ACT LED indicators, see the “LED Indicators” section.
An RSR10-02E series router provides two fixed 10/100/1000 Mbps Ethernet ports. The copper port uses an RJ-45
connector.
Features
The following table describes the basic features of the GE ports.
Table 1-9 Specifications of the GE ports
Parameter Description
Interface Two 10/100/1000Base-T/1000Base-TX interfaces
Interface
standard IEEE Std 802.3-2008
Cables
10/100/1000Base-T uses the Category 5e UTP or STP with the maximum transmission distance of 100 meters.
Straight-through cable: All wire pairs are in the same order on each end of the RJ45 cable. The straight-through cable is
used to connect a terminal device such as a PC or router to a hub or LAN switch.

Crossover cable: Pin 1 and pin 2 at one end of the cable correspond to pin 3 and pin 6 at the other end, respectively. The
crossover cable is used to connect two terminal devices, such as connecting a PC to a PC, and connecting a router to a
router.
If the port supports Auto-MDI/MDIX, both straight-through and crossover cables can be used.
Considering that you may customize cables, the following section describes how to wire straight-through and crossover
cables.
As shown in the following figure, the pins of the RJ-45 connector are numbered 1 to 8, counting from left to right when the
connector is viewed from the side without the latching tab.
Figure 1-10 RJ-45 Connector Pin Number
For a straight-through cable, use the same wiring.
Figure 1-11 Straight-through Wiring Diagram
For a crossover cable, swap the positions of the two pairs.
Figure 1-12 Crossover Wiring Diagram

USB Port
LED Indicator
For descriptions of USB port indicator, see the “LED Indicators” section.
Features
The RSR10-02E series router provides one fixed USB port, through which the user can read configurations from the USB
device, or save configurations to the USB device.
Table 1-10 Specifications of the USB Port
Index Parameters
Interface Standard USB 2.0
Connector USB Host
Rate 1.5 Mbps, 12 Mbps, 480 Mbps
Interface Type Host
Hot Swapping Supported
The hot swapping for the USB device must strictly follow the “Configuring Reliability” chapter in the related
software configuration guide. For the avoidance of system abnormality, hot swapping is not allowed unless
the command for unplugging the USB is entered.
The USB device here refers to USB flash disks.
Cables
If you connect a USB device with a USB extension cable, the cable must be less than 5 meters.
SD Card Slot
LED Indicator
For descriptions of SD card indicator, see the “LED Indicators” section.
Features
The RSR10-02E series router provides one fixed SD card slot, through which the user can read configurations from an SD
card, or save configurations to the SD card.
Table 1-11 Specifications of the SD Card Slot
Index Parameters
Interface Standard SD/SDHC
Connector SD connector, 1 FUNC button

Index Parameters
Rate 1.5 Mbps
Interface Type Device
SD Card Ruijie Networks SDHC card/ Kingston/ 4GB/ class_4
Hot Swapping Supported
The hot swapping for the SD device must strictly follow the “Configuring Reliability” chapter in the related
software configuration guide. For the avoidance of system abnormality, hot swapping is not allowed unless
the command for unplugging the SD card is entered.
Cables
Ruijie Networks SDCH card / Kingston /4GB/class_4
FUNC Button
FUNC Button Image
Figure 1-13 FUNC Button
The FUNC button is close to the USB interface on the front panel. It is used for one-button upgrade. To avoid careless
touching, the button is designed to be pressed using a tiny needle.
Features
One-button upgrade is the process that users press the FUNC button on the device panel to reset the system. Before the
system resets, you can use the files in SD cards or USB flash disks to upgrade software versions or configuration files, or
upgrade both of them simultaneously. The functions of one-button upgrade include:
One-button system reset
When no SD card or USB flash disk is inserted into the device, or an SD card or a USB flash disk is inserted but no
software versions or configuration files for upgrade exist, press the FUNC multi-functional button to reset the system.
The system will restart based on the original software versions.
One-button upgrade of software versions and configuration files

When an SD card or a USB flash disk is inserted into the device, press the FUNC button. Then, the system searches
for the installation packages and configuration files that are applicable to the current device in the root directories of
the SD card and USB flash disk in sequence. After successfully finding the corresponding installation packages and
configuration files, the system checks the validity of the files and then upgrades the device by using the installation
packages and configuration files. After the upgrade, the system resets and restarts based on the new software
versions and configuration files.
When a storage medium is inserted, the system scans for an SD card first. If no SD card is inserted or the
inserted SD card does not contain applicable installation packages or configuration files, the system scans
for a USB flash drive. If neither the inserted SD card nor the USB flash drive contains applicable installation
packages or configuration files, the software versions and configuration files are not upgraded. Only the
system resets, and restarts based on the original software versions and configuration files.
About SIC Cards
This section describes the features of SIC modules supported by the RSR10-02E series router.
SIC-1HS Synchronous Interface Card
Product model: SIC-1HS
Image and Indicators
Figure 1-14: SIC-1HS high-speed synchronous serial interface card
The SIC-1HS is a Type B SIC, which can be inserted in a slot marked with “B”.
Each card has an interface status indicator (LINK indicator) and the card Ready indicator.
The following table describes LED indicators.
Table 1-12 LED Indicators on the SIC-1HS Card
Indicator Status Meaning
Link On Physical link has been established successfully.
Off Failed to establish the physical link.
RDY
On Initialization completed.
Off Initialization failed.

Features
The following table describes basic features of high-speed synchronous serial interface (HS):
Table 1-13 Specifications of the SIC-1HS Card
Protocol V.24 and V.35 are supported with cable automatic identification.
Rate The synchronous port of a single-synchronous card supports from 9600 to 8192000 bps.
Indicator
There are two LED indicators.
One LED indicating the LINK status of one port, which turns on when the physical link is
set up and the upper layer protocol is up.
One LED indicating the RDY status of one link card, which turns on when the
motherboard detects the module.
Interface DB26
Environmental
Operating temperature: 0°C to 45°C
Operating humidity: 10% to 90% RH;
Storage temperature: –40°C to 70°C
EMC EMI: GB 9254-2008 Class A
EMS: GB/T 17618-1998
Cables
The following cables can be used:
V.24 DTE
V.24 DCE
V.35 DTE
V.35 DCE
V.35 DTE-V.35 DCE
The figures of these cables are as below.
V.24 DTE
One end of this cable is the DB25 male connector, and the other end is the DB26 male connector.
Figure 1-15 V.24 DTE cable
V.24 DCE
One end of this cable is the DB25 female connector, and the other end is the DB26 male connector.
Figure 1-16 V.24 DCE cable

V.35 DTE
One end of this cable is the DB34 male connector, and the other end is the DB26 male connector.
Figure 1-17 V.35 DTE cable
V.35 DCE
One end of this cable is the DB34 female connector, and the other end is the DB26 male connector.
Figure 1-18 V.35 DCE cable
V.35 DTE-V.35 DCE
Both ends of this cable are DB26 male connectors.
Figure1-19 V.35 DTE-V.35 DCE cable
The cables are customer supplied. All types of SIC-1HS cables connect to the router through the DB26 interface. Choose
connectors of the right type when purchasing cables. For the use of the cables, see Chapter 6.
ISDN Interface Card
Two models are available:

1-port ISDN U-interface card (SIC-1B-U)
1-port ISDN S/T interface card (SIC-1B-S/T)
Images and Indicators
The following figure shows the image of the 1-port ISDN U-interface card (SIC-1B-U).
Figure 1-20 ISDN-1B-U
The SIC-1B-U is a Type A SIC, which can be inserted in a slot marked with “A”.
The following figure shows the image of the 1-port ISDN S/T U-interface card (SIC-1B-S/T).
Figure 1-21 SIC-1B-S/T
The SIC-1B-S/T is a Type A SIC, which can be inserted in a slot marked with “A”.
Each card has a port working status ACT indicator and the card Ready indicator. Besides, each ISDN card has two status
indicators: B1 and B2.
The following table describes panel indicators.
Table 1-14 LED Indicators on the ISDN Card
Indicator Status Meaning
ACT Solid on The U interface or S/T is active.
Off The U interface or S/T is idle.
RDY
On Initialization completed.
Off Initialization failed.
B1 On B1 channel is active.
Off B1 channel is idle.
B2 On B2 channel is active.
Off B2 channel is idle.

Features
The following table describes the basic features:
Table 1-15 Specifications of the SIC-1B-U Card
Number of Ports One
Interface Type RJ-45 port (compatible with RJ-11)
Cables Telephone cable
Standard Compliance ITU-T I.430,Q.921,Q.931
Temperature: Operating temperature: 0°C to 45°C
Storage temperature: -40°C to 70°C
Humidity Operating humidity: 10% to 90% RH
EMC EMI: GB 9254-2008 Class A
EMS: GB/T 17618-1998
Table 1-16 Specifications of the SIC-1B-S/T Card
Number of Ports One
Interface Type RJ-45
Cables ISDN S/T cables
Terminal Resistance Built-in 100Ω
Standard compliance ITU-T I.430,Q.921,Q.931
Operating Temperature: Operating temperature: 0°C to 45°C
Storage temperature: -40°C to 70°C
Humidity Operating humidity: 10% to 90% RH
EMC EMI: GB 9254-2008 Class A
EMS: GB/T 17618-1998
Cables
The SIC-1B-U module uses standard telephone cables.
The SIC-1B-S/T module uses standard ISDN S/T cables or RJ-45 to R-J45 straight-through cables.
The cables are customer supplied.
SIC-1E1- F Interface Card
SIC card model: SIC-1E1-F
Image and Indicators
The following figure shows the image of a 1-port non-channelized E1 card (SIC-1E1-F).
Figure 1-22 SIC-1E1-F

The SIC-1E1-F is a Type C line card, which can be inserted in a slot marked with “C”.
The following table describes panel indicators.
Table 1-17 LED Indicators on the SIC-1E1-F Card
Indicator Status Meaning
Link Solid on Upper link has been established.
Off Failed to establish the upper link.
RDY On Initialization completed.
Off Initialization failed.
Features
The following table describes the basic features.
Table 1-18 Specifications of the SIC-1E1-F Card
Number of Ports One
Interface Type DB9 female connector
Cables Balanced cables or non-balanced cables
Standard Compliance ITU-T G.703
Operating Temperature Operating temperature: 0°C to 45°C
Storage temperature: -40°C to 70°C
Humidity Operating humidity: 10% to 90% RH
EMC EMI: GB 9254-2008 Class A
EMS: GB/T 17618-1998
Cables
The following cables are provided:
Balanced cable with the crystal connector
Balanced cable with the crystal jack
Non-balanced cable
Balanced cable with the RJ-45 Plug
One end is the DB9 male connector, and the other end is the RJ-45 plug. The characteristic impedance of the cable is
120Ω.
Figure 1-23: Balanced cable with the RJ-45 Plug