Ruijie RG-S5750-S Series Installation and operating manual

RG-S5750-S Series Switch
Hardware Installation and Reference Guide V1.15

Copyright Statement
Ruijie Networks©2015
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification,
transmission, translation or commercial use of this document or any portion of this document, in any form or by any means,
without the prior written consent of Ruijie Networks is prohibited.
, , , , ,
, ,, ,
, , are registered trademarks of Ruijie Networks.
Counterfeit is strictly prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain
the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will
not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

Preface
Thank you for using our products. This manual will guide you through the installation of the device.
This manual describes the functional and physical features and provides the device installation steps, hardware
troubleshooting, module technical specifications, and specifications and usage guidelines for cables and connectors.
Audience
It is intended for the users who have some experience in installing and maintaining network hardware. At the same time,
it is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks website: http://www.ruijienetworks.com/
Online customer services: http://webchat.ruijie.com.cn
Customer service center: http://www.ruijie.com.cn/service.aspx
Customer services hotline: [phone]
BBS:
http://support.ruijie.com.cn
Customer services email: [e-mail]
Related Documents
Documents Description
Configuration Guide Describes network protocols and related mechanisms that supported by the
product, with configuration examples.
Command Reference Describes the related configuration commands, including command modes,
parameter descriptions, usage guides, and related examples.
Symbol Conventions
Means reader take note. Notes contain helpful suggestions or references.
Means reader be careful. In this situation, you might do something that could result in equipment damage
or loss of data.

Chapter 1 Product Overview
The RG-S5750-S series switches are the next generation Layer 3 switches introduced by Ruijie Networks. Featuring high
performance, reliable security, and multiple services, the RG-S5750-S series switches are mainly applicable to the
convergence layer of large-scale networks to provide full wire-speed exchanging and complete QoS services, classify
different services according to different business needs and ensure the prompt transmission of key data. The
RG-S5750-S series switches can provide various medium interfaces to meet the requirement for interfaces in network
constructions.
RG-S5750-S Series Switches
Table1-1
Model
10/100/1000Base-T
adaptive Ethernet
port
1000Base-X
SFP port
Console
Port
USB
Port
Extension
Module
Slot
Redundant
Power
Supply
RG-S5750-24GT/8SFP-S 24 8 (Combo) 1 0 2 RPS
RG-S5750-48GT/4SFP-S 48 4 (Combo) 1 0 2 RPS
RG-S5750-24SFP/8GT-S 8 (combo) 24 1 1 2 Dual power
supplies
RG-S5750-24GT/8SFP-S
Technical Specifications
Table1-2
Model RG-S5750-24GT/8SFP-S
Optical Module
Type
Ethernet 100M:
FE-SFP-LX-MM1310
FE-SFP-LH15-SM1310
FE-SFP-LX20-SM1310-BIDI
FE-SFP-LX20-SM1550-BIDI
FE-SFP-LH40-SM1310-BIDI
FE-SFP-LH40-SM1550-BIDI
Ethernet 1000M:
Mini-GBIC-SX
Mini-GBIC-LX
Mini-GBIC-LH40
GE-SFP-LX20-SM1310-BIDI
GE-SFP-LX20-SM1550-BIDI
GE-SFP-LH40-SM1310-BIDI
GE-SFP-LH40-SM1550-BIDI

Mini-GBIC-ZX50
Mini-GBIC-ZX80
Mini-GBIC-ZX100
1000Base-T:
Mini-GBIC-GT
The supported module type may change at any time. For the detailed change
information, consult the Ruijie Networks.
The Bi-Directional (BIDI) optical modules must be used in pairs. For details about
the pairs of BIDI modules, see the Appendix B.
Extended Module
Type
M5000E-02SFP/GT
M5000E-01XS
M5000E-02XS
SFP Port 100Base-X
1000Base-X
RPS Type RG-RPS150
Power Supply AC input:
Rated voltage range: 100–240 V AC
Maximum voltage range: 90–264 V AC
Frequency: 50/60 Hz
Rated current: 1.5 A
HVDC input:
Voltage range: 192–290 V DC
Current range: 0.5–0.24 A
Max. Power
Consumption
58 W (with extension modules); 42 W (without extension modules)
Temperature Working temperature: 0–50ºC
Storage temperature: -40–70ºC
Humidity Working humidity: 10%–90% RH
Storage humidity: 5%–90% RH
Fan Support adjustment of fan speed and warning of fan trouble.
Temperature
Warning Temperature warning function
EMC GB9254-2008
Security
Compliance
GB4943-2011
Dimensions
(W x D x H)
440 mm x 260 mm x 44 mm
Weight 4.6 kg (with extension modules); 3.6 kg (without extension modules)

RG-S5750-24GT/8SFP-S switch is a class A product. In a domestic environment, this product may cause
radio interference in which case the user may be required to take adequate measures.
Product Appearance
The front panel of the RG-S5750-24GT/8SFP-S Ethernet switch provides twenty four 10/100/1000Base-T Ethernet ports,
eight 1000M SFP fiber/copper combo ports, one Console port and one USB port. The back panel provides AC power input
ports, RPS input ports and two extension module slots.
Figure 1-1 Appearance of the RG-S5750-24GT/8SFP-S
Front Panel
Figure 1-2 RG-S5750-24GT/8SFP-S Front Panel
Note: 1. Switch status indicator
2. Extension module 1 status indicator
3. Extension module 2 status indicator
4. RPS status indicator
5. Console port
6. 10/100/1000Base-T adaptive Ethernet port
7. Port status indicator
8. 100/1000Base-X SFP port
9. USB port
Back Panel
Figure 1-3 RG-S5750-24GT/8SFP-S Back Panel

Note: 1. Grounding pole
2. 3-core AC power port
3. Power defense shedding plug
4. RPS input port
5. Slot for extension module 1
6. slot for Extension module 2
Power Supply System
The RG-S5750-24GT/8SFP-S adopts the AC power input and RPS input.
AC input:
Rated voltage range: 100–240 V AC
Maximum voltage range: 90–264V AC
Frequency: 50/60 Hz
Rated current: 1.5 A
Power cable: 10 A power cable
HVDC input:
Voltage range: 192–290 V DC
Current range: 0.5–0.24 A
RPS input:
The switch power can be supplied by the redundant power input or both the AC input and redundant power input.
When both the AC input and the redundant power input are available, the switch power is supplied by the AC power
input;
When the AC input is unavailable, the switch power supply switches to the redundant power input seamlessly.
At present, the redundant power supply interface can be used together with the RPS150 that are
manufactured by Ruijie Networks. Unless otherwise stated, other power supply modules cannot be used for
power input; otherwise, an abnormality may occur or damage the switch.
Cooling System
The RG-S5750-24GT/8SFP-S is designed with left and right fans for heat dissipation purposes, thereby ensuring the
device's functioning in the specified environment. Sufficient space (10 cm distance from both sides and the backplane of
the cabinet) should be reserved to allow air circulation. Dust the device every three months to avoid blocking the
ventilation openings.
Figure 1-4 Flow Scheme of Heat Dissipation

LED Indicators
Table1-4
Indicator Panel Identification Status Meaning
Off The switch is not powered on.
Blinking green The switch is being initialized. If the blinking
persists, however, it indicates that an
abnormality occurs.
Solid green The switch is operational.
Solid yellow It indicates a warning on the switch temperature.
Check the working environment of the switch
immediately.
Status indicator Status
Solid red Indicates a fault on the switch. For details, refer
to Section 5.2 Troubleshooting Common Faults.
Off There is no extension module or the extension
module is not correctly installed.
Extension module
indicator M1 / M2
Solid green The extension module is correctly installed.
Off The redundant power is not connected to a link.
Solid green The redundant power is connected and can
supply power.
Solid yellow The redundant power is supplying power.
RPS status indicator
RPS
Solid red The redundant power is connected but cannot
supply power.
Off No link, or port was administratively shut down.
Solid green The 1000 M link that the port connects to is Up.
Blinking green Data at a rate of 1000 M are being transceived at
the port.
Solid yellow The 100 M link that the port connects to is Up.
1000Mbps SFP port
indicator
21F-24F
Blinking yellow Data at a rate of 100 M are being transceived at
the port.

Indicator Panel Identification Status Meaning
Off No link, or port was administratively shut down.
Solid green The 1000 M link that the port connects to is Up.
Blinking green Data at a rate of 1000 M are being transceived at
the port.
Solid yellow The 100 or 10 M link that the port connects to is
Up.
1000Mbps RJ-45
port indicator
1-24
Blinking yellow Data at a rate of 100 or 10 M are being
transceived at the port.
RG-S5750-48GT/4SFP-S
Technical Specifications
Table1-5
Model RG-S5750-48GT/4SFP-S
Optical Module
Type
Ethernet 100 MB:
FE-SFP-LX-MM1310
FE-SFP-LH15-SM1310
FE-SFP-LX20-SM1310-BIDI
FE-SFP-LX20-SM1550-BIDI
FE-SFP-LH40-SM1310-BIDI
FE-SFP-LH40-SM1550-BIDI
Ethernet 1000 MB:
Mini-GBIC-SX
Mini-GBIC-LX
Mini-GBIC-LH40
GE-SFP-LX20-SM1310-BIDI
GE-SFP-LX20-SM1550-BIDI
GE-SFP-LH40-SM1310-BIDI
GE-SFP-LH40-SM1550-BIDI
Mini-GBIC-ZX50
Mini-GBIC-ZX80
Mini-GBIC-ZX100
1000Base-T:
Mini-GBIC-GT
The supported module type may change at any time. For the detailed change
information, consult the Ruijie Networks.
The Bi-Directional (BIDI) optical modules must be used in pairs. For details about

the pairs of BIDI modules, see the Appendix B.
Extended Module
Type
M5000E-02SFP/GT
M5000E-01XS
M5000E-02XS
SFP Port 100Base-X
1000Base-X
RPS Type RG-RPS150
Power Supply AC input:
Rated voltage range: 100–240 V AC
Maximum voltage range: 90–264 V AC
Frequency: 50/60 Hz
Rated current: 2 A
HVDC input:
Voltage range: 192–290 V DC
Current range: 0.7–0.5 A
Max. Power
Consumption
82 W (with extension modules); 66 W (without extension modules)
Temperature Working temperature: 0–50ºC
Storage temperature: -40–70ºC
Humidity Working humidity: 10%–90% RH
Storage humidity: 5%–90% RH
Fan Support fan speed adjustment and the fault warning function
Temperature
Warning
Support the temperature warning function
EMC GB9254-2008
Security
Compliance
GB4943-2011
Dimensions
(W x D x H)
440 mm x 300 mm x 44 mm
Weight 5.2 kg (with extension modules); 4.2 kg (without extension modules)
RG-S5750-48GT/4SFP-S switch is a class A product. In a domestic environment, this product may cause
radio interference in which case the user may be required to take adequate measures.
Product Appearance

The front panel of the RG-S5750-48GT/4SFP-S Ethernet switch provides 48 10/100/1000Base-T Ethernet ports, four
1000M SFP fiber/copper combo ports, one Console port and one USB port. The back panel provides AC power input
ports, RPS input ports and two extension module slots.
Figure 1-5 Appearance of the RG-S5750-48GT/4SFP-S
Front Panel
Figure 1-6 Schematic Diagram of the RG-S5750-48GT/4SFP-S Front Panel
Note: 1. Switch status indicator
2. Extension port 1 status indicator
3. Extension port 2 status indicator
4. RPS status indicator
5. Console port
6. 10/100/1000Base-T adaptive Ethernet port
indicator
7. Port status indicator
8. 100/1000Base-X SFP port
9. USB port
Back Panel
Figure 1-7 Schematic Diagram of the RG-S5750-48GT/4SFP-S Back Panel
Note: 1. Grounding pole
2. 3-core AC power port
3. Power defense shedding plug
4. RPS input port
5. Slot for extension module 1
6. Slot for extension module 2
Power Supply System

The RG-S5750-48GT/4SFP-S adopts the AC power input and redundant power input.
AC input:
Rated voltage range: 100–240 V AC
Maximum voltage range: 90–264 V AC
Frequency: 50/60 Hz
Rated current: 2 A
Power cable: 10 A power cable
HVDC input:
Voltage range: 192–290 V DC
Current range: 0.7–0.5 A
RPS input:
The switch power can be supplied by the redundant power input or both the AC input and redundant power input.
When both the AC input and the redundant power input are available, the switch power is supplied by the AC power
input.
When the AC input is unavailable, the switch power supply switches to the redundant power input seamlessly.
At present, the redundant power supply interface can be used together with the RPS150 that are
manufactured by Ruijie Networks. Unless otherwise stated, other power supply modules cannot be used for
power input; otherwise, an abnormality may occur or damage the switch.
Cooling System
The RG-S5750-48GT/4SFP-S adopts left and right fans for heat dissipation purposes, thereby ensuring the device's
functioning in the specified environment. Sufficient space (10 cm distance from both sides and the backplane of the
cabinet) should be reserved around the cabinet to allow air circulation. Dust the device every three months to avoid
blocking the ventilation openings.
Figure 1-8 Flow Scheme of Heat Dissipation

LED Indicators
Table1-6
Indicator Panel Identification Status Meaning
Off The switch is not powered on.
Blinking green The switch is being initialized. If the blinking
persists, however, it indicates that an abnormality
occurs.
Solid green The switch is operational.
Solid yellow It indicates a warning on the switch temperature.
Check the working environment of the switch
immediately.
Status indicator Status
Solid red Indicates a fault on the switch. For details, refer
to Section 5.2 Troubleshooting Common Faults.
Off There is no extension module or the extension
module is not correctly installed.
Extension module
indicator M1 / M2
Solid green The extension module is correctly installed.
Off The redundant power is not connected to a link.
Solid green The redundant power is connected and can
supply power.
Solid yellow The redundant power is supplying power.
RPS status indicator
RPS
Solid red The redundant power is connected but cannot
supply power.
Off T No link, or port was administratively shut down.
Solid green The 1000 M link that the port connects to is Up.
Blinking green Data at a rate of 1000 M are being transceived at
the port.
Solid yellow The 100 M link that the port connects to is Up.
1000Mbps SFP port
indicator
45F-48F
Blinking yellow Data at a rate of 100 M are being transceived at
the port.
Off No link, or port was administratively shut down.
Solid green The 1000 M link that the port connects to is Up.
Blinking green Data at a rate of 1000 M are being transceived at
the port.
Solid yellow The 100 or 10 M link that the port connects to is
Up.
1000Mbps RJ-45
port indicator
1-48
Blinking yellow Data at a rate of 100 or 10 M are being
transceived at the port.
RG-S5750-24SFP/8GT-S
Technical Specifications
Table1-7

Model RG-S5750-24SFP/8GT-S
Optical Module
Type
Ethernet 100 MB:
FE-SFP-LX-MM1310
FE-SFP-LH15-SM1310
FE-SFP-LX20-SM1310-BIDI
FE-SFP-LX20-SM1550-BIDI
FE-SFP-LH40-SM1310-BIDI
FE-SFP-LH40-SM1550-BIDI
Ethernet 1000 MB:
Mini-GBIC-SX
Mini-GBIC-LX
Mini-GBIC-LH40
GE-SFP-LX20-SM1310-BIDI
GE-SFP-LX20-SM1550-BIDI
GE-SFP-LH40-SM1310-BIDI
GE-SFP-LH40-SM1550-BIDI
Mini-GBIC-ZX50
Mini-GBIC-ZX80
Mini-GBIC-ZX100
1000Base-T:
Mini-GBIC-GT
The supported module type may change at any time. For the detailed change
information, consult the Ruijie Networks.
The Bi-Directional (BIDI) optical modules must be used in pairs. For details about
the pairs of BIDI modules, see the Appendix B.
Extended Module
Type
M5000E-02SFP/GT
M5000E-01XS
M5000E-02XS
SFP Port 100Base-X
1000Base-X
RPS Type Dual power supplies
Power Supply AC input:
Rated voltage range: 100–240 V AC
Maximum voltage range: 90–264 V AC
Frequency: 50/60 Hz
Rated current: 2 A
HVDC input:
Voltage range: 192–290 V DC

Current range: 0.5–0.24 A
Max. Power
Consumption
Dual power supplies:
50 W (with extension modules); 34 W (without extension modules)
Single power supply:
48 W (with extension modules); 33 W (without extension modules)
Temperature Working temperature: 0–50ºC
Storage temperature: -40–70ºC
Humidity Working humidity: 10%–90% RH
Storage humidity: 5%–90% RH
Fan Support fan speed adjustment and the fault warning function
Temperature
Warning
Support the temperature warning function
EMC GB9254-2008
Security
Compliance
GB4943-2011
Dimensions
(W x D x H)
440 mm x 300 mm x 44 mm
Weight 5.2 kg (with extension modules and power modules); 3.7 kg (without extension modules or
power modules)
RG-S5750-24SFP/8GT-S switch is a class A product. In a domestic environment, this product may cause
radio interference in which case the user may be required to take adequate measures.
Product Appearance
The front panel of the RG-S5750-24SFP/8GT-S Ethernet switch provides 24 1000Base-X SFP ports, eight 1000M
copper RJ-45 combo ports, one Console port, one USB port, two power module slots and two extension slots.
Figure 1-9 Appearance of the RG-S5750-24SFP/8GT-S

Front Panel
Figure 1-10 Schematic Diagram of the RG-S5750-24SFP/8GT-S Front Panel
Note: 1. Switch status indicator
2. Power supply 1 status indicator
3. Power supply 2 status indicator
4. Extension port 1 status indicator
5. Extension port 2 status indicator
6. USB port
7. Console port
8. 100/1000Base-X SFP port
9. Port status indicator
10. 10/100/1000Base-T adaptive Ethernet port
Back Panel
Figure 1-11 Schematic Diagram of the RG-S5750-24SFP/8GT-S Back Panel
Note: 1. Slot for the power module 1
2. Slot for the power module 2
3. Slot for the extension module 1
4. Slot for the extension module 2
5. Grounding pole
Power Supply System
The RG-S5750-24SFP/8GT-S supports two power supplies. The supported power supply module is RG-M5000E-AC60.
Dual power supplies mean that the switch can use either or both of the two power supplies concurrently. When the two
power supply modules are used concurrently, the switch is powered by the equalizing current status.
Table1-8 Technical Specifications of the RG-M5000E-AC60 Power Module
Model RG-M5000E-AC60 (AC Input) RG-M5000E-AC60 (HVDC Input)

Applicable Models RG-S5750-24SFP/8GT-S RG-S5750-24SFP/8GT-S
Rated Input Voltage
Range
100–240 VAC, 50/60 Hz 240 VDC
Maximum Input
Voltage Range
90–264 VAC, 50/60 Hz 192–290 VDC
Power 60 W
Power Supply
Hot-Plugging
Supported
Power Supply
Redundancy
1+1 redundancy
Over-Voltage
Protection
13.4–16 V
Over-Current
Protection 6–12 A
Over-Heat
Protection
Not supported
Flow Equalization Not supported
Mixed Power
Supply
Not supported
Power Cable 10 A power cable
Dimensions 203.3 mm x 81 mm x 40 mm (excluding connecting finger and handle)
236.9 mm x 81 mm x 40 mm (including connecting finger and handle)
Weight 0.6 kg
Cooling System
The RG-S5750-24SFP/8GT-S is designed with left and right fans, and heat dissipation of power supply and extension
modules, thereby ensuring the device's functioning in the specified environment. Sufficient space (10 cm distance from
both sides and the backplane of the cabinet) should be reserved to allow air circulation. Dust the device every three
months to avoid blocking the ventilation openings.
Figure 1-12 Flow Scheme of Heat Dissipation

LED Indicators
Table1-9
Indicator Panel Identification Status Meaning
Off The switch is not powered on.
Blinking green The switch is being initialized. If the blinking
persists, however, it indicates that an
abnormality occurs.
Solid green The switch is operational.
Solid yellow It indicates a yellow warning on the switch
temperature. Check in time the working
environment of the switch.
Status indicator Status
Solid red Indicates a fault on the switch. For details, refer
to the section of Troubleshooting Common
Faults.
Off The power supply is off.
Solid red The power supply is on but is not connected with
the AC power cable or the power supply fails.
Power supply status
indicator PWR1/PWR2
Solid green The power supply is operational.

Indicator Panel Identification Status Meaning
Off There is no extension module or the extension
module is not correctly installed.
Extension module
indicator M1 / M2
Solid green The extension module is correctly installed.
Off No link, or port was administratively shut down.
Solid green The port is connected at 1000Mbps.
Blinking green The port is receiving or transmitting data at
1000Mbps.
Solid yellow The port is connected at 100Mbps.
1000Mbps SFP port
indicator
1F-24F
Blinking yellow The port is receiving or transmitting data at
100Mbps.
Off No link, or port was administratively shut down.
Solid green The port is connected at 1000Mbps.
Blinking green The port is receiving or transmitting data at
1000Mbps.
Solid yellow The port is connected at 10/100Mbps.
1000Mbps RJ-45
port indicator
17-24
Blinking yellow The port is receiving or transmitting data at
10/100Mbps.
Modules
The RG-S5750-S series switches support the following modules: M5000E-02SFP/GT, M5000E-01XS and M5000E-02XS.
The M5000E-02SFP/GT module provides two 1000M fiber/copper combo ports. The 1000M copper port is the
10/100/1000M adaptive RJ45 port supporting the cat-5 UTP and STP; while the 1000M fiber port supports only the
100/1000Base-X mode, and it can be used together with multiple types of optical transceiver modules of Ruijie
Networks for different transmission distances. When you use this module for the RG-S5750-S series switches, the
1000M fiber ports support the SFP Bi-Directional (BIDI) module. For information about the supported SFP BIDI
modules and relevant usage, see the Appendix B.
M5000E-01XS provides a 10G SFP Plus port module and support the 10GBASE-SR/LR/LRM model. It can be used
with various optical transceiver modules of Ruijie Networks for different transmission distances. This module
supports one-meter or three-meter SFP Plus passive copper cable on the RG-S5750-S series switches. It can be
used together with XG-SFP-CU1M and XG-SFP-CU3M copper cable transceiver modules of Ruijie Networks.
The M5000E-02XS provides two 10G SFP Plus ports and supports the 10GBASE-SR/LR/LRM mode. It can be used
together with multiple types of optical transceiver modules manufactured by Ruijie Networks to adapt different
transmission distances. This module supports one-meter or three-meter SFP Plus passive copper cable on the
RG-S5750-S series switches. It can be used together with XG-SFP-CU1M and XG-SFP-CU3M copper cable
transceiver modules of Ruijie Networks.
Table1-10
Module Description External port
M5000E-02SFP/GT 2-port 1000M fiber/copper
combo module
2 10/100/1000Base-T adaptive Ethernet ports.
2 Combo 1000Base-X SFP ports.

M5000E-01XS 1-port 10G interface module 1 SFP Plus port
M5000E-02XS 2-port 10G interface module 2 SFP Plus ports
The 1000Base-X SFP port and the corresponding 10/100/1000Base-T adaptive Ethernet port form a
fiber/copper combo port. That is, only one port in the fiber/copper combo port is available at a particular time.
For the detailed description about those two modules, see Switch Extension Module Manual.