Ruijie Reyee RAP6260-D Installation and operating manual

Ruijie Reyee RG-RAP6260(H)-D Access
Point
Hardware Installation and Reference Guide
Document Version: V1.0
Date: January 30, 2023
Copyright © 2023 Ruijie Networks

Copyright
Copyright © 2023 Ruijie Networks
All rights are reserved in this document and this statement.
Any reproduction, excerption, backup, modification, transmission, translation orcommercial use ofthis document
or any portion of this document, in any form or by any means, without the prior written consent of Ruijie Networks
is prohibited.
Trademarks including , are owned by Ruijie Networks.
All other trademarks or registered trademarks mentioned in this document are owned by their respective owners.
Disclaimer
The products, services, or features you purchase are subject to commercial contracts and terms. Some or all of
the products, services or features described in this document may not be within the scope of your purchase or
use. Unless otherwise agreed in the contract, Ruijie Networks does not make any express or implied statement
or guarantee for the content of this document.
Due to product version upgrades or other reasons, the content of this document will be updated from time to
time. Ruijie Networks reserves the right to modify the content of the document without any notice or prompt.
This manual is for reference only. Ruijie Networks endeavors to ensure content accuracy and will not shoulder
any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

I
Preface
Intended Audience
This document is intended for:
Network engineers
Technical support and servicing engineers
Network administrators
Technical Support
Official website of Ruijie Reyee: https://www.ruijienetworks.com/products/reyee
Technical Support Website: https://ruijienetworks.com/support
Case Portal: https://caseportal.ruijienetworks.com
Community: https://community.ruijienetworks.com
Technical Support Email: [email protected]
Conventions
1. GUI Symbols
Interface
symbol
Description
Example
Boldface
1. Button names
2. Window names, tab name, field name and
menu items
3. Link
1. Click OK.
2. Select Config Wizard.
3. Click the Download File link.
>
Multi-level menus items
Select System >Time.
2. Signs
The signs used in this document are described as follows:
Warning
An alert that calls attention to important rules and information that if not understood or followed can result in
data loss or equipment damage.
Caution
An alert that calls attention to essential information that if not understood or followed can result in function
failure or performance degradation.
Note
An alert that contains additional or supplementary information that if not understood or followed will not lead to
serious consequences.

II
Specification
An alert that contains a description of product or version support.
3. Note
This manual provides the device installation steps, hardware troubleshooting, module technical specifications,
and specifications and usage guidelines for cables and connectors. It is intended for the users who have some
experience in installing and maintaining network hardware. At the same time, it is assumed that the users are
already familiar with the related terms and concepts.

I
Contents
Preface.................................................................................................................................................. I
1 Product Overview.............................................................................................................................. 1
1.1 About the RG-RAP6260(H)-D Access Point .............................................................................1
1.2 Package Contents......................................................................................................................1
1.3 Hardware Features....................................................................................................................2
Access Point...................................................................................................................2
Ports and LED................................................................................................................3
Reset Hole .....................................................................................................................4
1.4 Technical Specifications............................................................................................................5
1.5 Power Specifications .................................................................................................................7
1.6 Heat Dissipation.........................................................................................................................8
2 Preparing for Installation................................................................................................................... 9
2.1 Safety Precautions.....................................................................................................................9
General Safety Precautions...........................................................................................9
Handling Safety..............................................................................................................9
Electric Safety................................................................................................................9
Laser Safety.................................................................................................................10
2.2 Installation Environment Requirements...................................................................................10
Bearing Requirements.................................................................................................10
Ventilation Requirements.............................................................................................10
Temperature/Humidity Requirements..........................................................................10
Waterproof Requirement..............................................................................................11
Grounding Requirement ..............................................................................................11

II
Anti-interference Requirements...................................................................................11
2.3 Tools ........................................................................................................................................11
3 Installing theAccess Point.............................................................................................................. 12
3.1 Installation Flowchart...............................................................................................................12
3.2 Before You Begin.....................................................................................................................12
3.3 Precautions..............................................................................................................................13
3.4 Installing the Access Point.......................................................................................................13
Installing the MountingArm .........................................................................................14
Wall Mounting ..............................................................................................................15
Vertical Pole Mounting.................................................................................................16
Horizontal Pole Mounting.............................................................................................17
Adjusting Orientation....................................................................................................18
3.5 Installing the Cable..................................................................................................................20
Installing the Ethernet Cable........................................................................................20
Installing the Grounding Cable....................................................................................20
3.6 Bundling Cables.......................................................................................................................21
Precautions..................................................................................................................21
Steps............................................................................................................................21
3.7 Checklist After Installation .......................................................................................................21
4 Verifying Operating Status .............................................................................................................. 22
4.1 Setting up Configuration Environment.....................................................................................22
4.2 Powering on the Access Point.................................................................................................22
Checklist Before Power-on..........................................................................................22
ChecklistAfter Power-on .............................................................................................22

III
5 Monitoring and Maintenance........................................................................................................... 23
5.1 Monitoring................................................................................................................................23
5.2 Hardware Maintenance............................................................................................................23
6 Common Troubleshooting............................................................................................................... 24
6.1 General Troubleshooting Flowchart ........................................................................................24
6.2 Common Faults........................................................................................................................24
7 Appendix.......................................................................................................................................... 25
7.1 Connectors and Media.............................................................................................................25
2500BASE-T/1000BASE-T/100BASE-TX Port ...........................................................25
Fiber-Optic Cable Connection .....................................................................................26
7.2 Mini-GBIC Modules..................................................................................................................27
7.3 Cabling.....................................................................................................................................29

Hardware Installation and Reference Guide Product Overview
1
1 Product Overview
1.1 About the RG-RAP6260(H)-D Access Point
The RG-RAP6260(H)-D is a dual-radio access point designed to cover a medium or large outdoor area.
Compliant with the IEEE 802.11a/b/g/n/ac/ax standard, the access point can work at the 2.4 GHz and 5 GHz
bands at the same time and supports quad-stream MU-MIMO. The access point provides a combined data rate
of about 6000 Mbps, with up to 1148 Mbps in the 2.4 GHz band and 4804 Mbps in the 5 GHz band. The access
point provides one 2.5GE electrical port and one 1GE optical port. The electrical port adopts either IEEE 802.3bt
PoE power supply or 48 V DC local power supply.
The enclosure of RG-RAP6260(H)-D meets the IP68 protection grade, which withstands the extreme outdoor
environment and can effectively avoid the influence of bad weather and environment. The mounting method
greatly simplifies the installation and maintenance.
RG-RAP6260(H)-D is PoE-capable and can be applied to a wide variety of outdoor scenarios in the industries
including higher education, government, health care, general education, finance and business.
1.2 Package Contents
Table 1-1 Package Contents
Item
Quantity
RG-RAP6260(H)-D Access Point
1
Hose Clamp
2
Mounting Plate Assembly
1
M8 x 20 mm Screws
6
M8 x 60 mm Expansion Anchors
4
User Manual
1
Warranty Card
1
Cable Gland for SFP Port
1
Cable Gland for Ethernet Port (Pre-installed on the
access point)
1
SFP Port Plug (Pre-installed on the access point)
1
Mounting Arm
1
DC Connector Plug (Pre-installed on the access point)
1
Cable Gland for DC Connector
1

Hardware Installation and Reference Guide Product Overview
2
Item
Quantity
Grounding Cable
1
Note
The package contents generally contain the above items. The actual delivery is subject to the order
contract. And please check your goods carefully against the order contract. If you have any questions,
please contact the distributor.
1.3 Hardware Features
Access Point
Figure 1-1 Access Point

Hardware Installation and Reference Guide Product Overview
3
Ports and LED
Figure 1-2 Ports
Table 1-2 Ports
No.
Ports
Description
1
DC Connector
48 V DC/1 A input
2
Ethernet/PoE
Port
100/1000/2500Base-T Ethernet ports, PoE-capable
3
Reset Hole
The Reset hole is near the Ethernet/PoE port.
Stick the pin to the Reset hole: Restart the access point.
Press and hold the pin to the Reset hole for more than 5 seconds:
Restore the access point to factory settings.
4
SFP Port
1000Base-X SFP port (The SFP transceiver is an optional accessory.)

Hardware Installation and Reference Guide Product Overview
4
Figure 1-3 LED
Table 1-3 LED
Color
Status
Solid Blue
The access point is operating normally without alarms.
Off
The access point is not receiving power.
Slow Blinking
The access point is operating normally but there is an alarm generated.
Fast Blinking
Possible cases:
1. Restoring the access point to factory settings.
2. Upgrading the firmware.
3. Handling alarms automatically.
4. Starting up the access point.
Reset Hole
RG-RAP6260(H)-D supports cloud-based management. To reset the access point, you are advised to
connect the access point to the Internet and perform reset on Ruijie Cloud.
If it is inconvenient to connect to the Internet, insert a pin into the Reset hole as marked by red point. Press
and hold the pin for over 5 seconds, and the access point will be restored to factory settings.

Hardware Installation and Reference Guide Product Overview
5
Figure 1-4 Reset Hole
Warning
You are advised to loosen the cable gland before using the Reset hole. Please see Installing the Ethernet
Cable for details.
1.4 Technical Specifications
Table 1-4 Technical Specifications
Radio Design
Dual-radio, four spatial streams
Standard &
Protocol
802.11ax, 802.11ac wave2/wave1, and 802.11a/b/g/n
Operating
Radio
802.11b/g/n/ax: 2.4 GHz to 2.4835 GHz
802.11a/n/ac/ax: 5.150 GHz to 5.350 GHz, 5.470 GHz to 5.725 GHz, 5.725 GHz to
5.850 GHz
Antenna
Built-in directional antennas (2.4 GHz: 10 dBi; 5 GHz: 9 dBi)
Lobe Angle
2.4 GHz: Horizontal lobe angle of 50°and vertical lobe angle of 30°
5 GHz: Horizontal lobe angle of 60°and vertical lobe angle of 30°
Coverage
Radius
In the case of straight-line distance with no obstacle:
Recommended:
5 GHz: 300 m (984.25 ft.)
2.4 GHz: 100 m (328.08 ft.)
Max.:
5 GHz: 500 m (1640.42 ft.)
2.4 GHz: 200 m (656.17 ft.)
Spatial Streams
2.4 GHz: 4 x 4 MIMO
5 GHz: 4 x 4 MIMO

Hardware Installation and Reference Guide Product Overview
6
Max. Data Rate
2.4 GHz: 1148 Mbps
5 GHz: 4804 Mbps
Combined: 5952 Mbps
Modulation
OFDM: BPSK@6/9 Mbps, QPSK@12/18 Mbps, 16QAM@24 Mbps, 64QAM@48/54
Mbps
DSSS: DBPSK@1 Mbps, DQPSK@2 Mbps, and [email protected]/11 Mbps
MIMO-OFDM: BPSK, QPSK, 16QAM, 64QAM, 256QAM and 1024QAM
OFDMA
Receiver
Sensitivity
11b: –96 dBm (1 Mbps), –93 dBm (5 Mbps), –89 dBm (11 Mbps)
11a/g: –91 dBm (6 Mbps), –85 dBm(24Mbps), –80 dBm (36 Mbps), –74 dBm ( 54
Mbps)
11n: –90 dBm (MCS0), –70 dBm (MCS7), –89 dBm (MCS8), –68 dBm (MCS15)
11ac: 20 MHz: –88 dBm (MCS0), –63 dBm (MCS9)
11ac: 40 MHz: –85 dBm (MCS0), –60 dBm (MCS9)
11ac: 80 MHz: –85 dBm (MCS0), –60 dBm (MCS9)
11ax: 80 MHz: –82 dBm (MCS0), –57 dBm (MCS9), –52 dBm (MCS11)
11ax: 160 MHz: –75 dBm (MCS0), –55 dBm (MCS9), –50 dBm (MCS11)
Max. Transmit
Power
400 mw (26 dBm)
Note: The transmit power is country-specific.
Power
Adjustment
Configurable in increments of 1 dBm
Dimensions
(W x D x H)
300 mm ×300 mm ×75.5 mm (11.81 in. x 11.81 in. x 2.97 in., without the mounting
plate)
Weight
≤3.5 kg (7.72 lbs., without the mounting plate)
Service Ports
One 100/1000/2500Base-T Ethernet port, PoE-capable
One 1000Base-X SFP port (The SFP transceiver is an optional accessory.)
Note: The access point itself does not transmit optical signals.An optical transceiver
module must be installed on the access point to convert optical signals into electrical
signals.
Management
Port
N/A
Status LED
One LED (blue)
Power Supply
There are three power supply modes available:

Hardware Installation and Reference Guide Product Overview
7
Standard PoE: IEEE 802.3bt standard (PoE++), backward compatible with the
IEEE 802.3at standard (PoE+), with a data rate up to 574 Mbps in the 2.4 GHz
band and 2402 Mbps in the 5 GHz band.
60 W Passive PoE adapter (Optional accessory)
Local power supply: 48 V DC /1 A
Note: The access point is not 802.3af-compliant. (See Power Specifications for
power supply modes and respective date rate.)
Max. Power
Consumption
Local power supply: 48 V DC/1 A
40 W
IEEE 802.3bt PoE power supply
60 W passive PoE power supply
IEEE 802.3at PoE power supply
25 W
Environment
Operating temperature: –40°C to 65°C (–40°F to 149°F)
Storage temperature: –40°C to 85°C (–40°F to 185°F)
Operating humidity: 0% to 100% RH (non-condensing)
Storage humidity: 0% to 100% RH (non-condensing)
Installation
Method
Wall mounting and pole mounting
Recommended mounting height: 2.5 m to 3 m (98.43 in. to 118.11 in.)
Surge
Protection
2 KV
Certification
CE
MTBF
> 400,000 hours
Caution
In a domestic environment, this product may cause radio interference in which case the user may be
required to take adequate measures.
1.5 Power Specifications
The access point can be powered by either PoE or DC power supply.
In a PoE power supply scenario, the power source equipment (PSE) must be at least 802.3at-capable. You
are advised to use an 802.3bt-capable PSE. If you want to use a PoE adapter, a Rujie-certificated PoE
adapter is recommended.
In a DC power supply scenario, use a 48 V DC/1 A power adapter with a 5.5 mm x 2.1 mm x 10 mm (0.22 in.
x 0.08 in. x 0.39 in.) plug.

Hardware Installation and Reference Guide Product Overview
8
Table 1-5 Power Supply Mode
Power Input
Standard PoE: IEEE 802.3bt standard, backward compatible with the IEEE 802.3at
standard
Local power supply: 48 V DC/1 A
Power Supply Mode
2.4 GHz
5 GHz
Data Rate
Max. Power
Consumption
IEEE 802.3bt
Standard
(Recommended)
4 x 4
4 x 4
5952 Mbps
40 W
60 W Passive PoE
Adapter
(Recommended)
4 x 4
4 x 4
5952 Mbps
40 W
Local Power Supply
(48 V DC /1 A)
4 x 4
4 x 4
5952 Mbps
40 W
IEEE 802.3at
Standard
2 x 2
2 x 2
2976 Mbps
25 W
Note: The 60 W passive PoE adapter is an optional accessory. The access point is not 802.3af-compliant.
1.6 Heat Dissipation
Maintain a sufficient clearance around the access point for proper ventilation.

Hardware Installation and Reference Guide Preparing for Installation
9
2 Preparing for Installation
2.1 Safety Precautions
Note
To avoid personal injury and device damage, carefully read the safety precautions before you install the
access point.
The following safety precautions may not cover all possible hazardous situations.
General Safety Precautions
Do not expose the access point to high temperature, dusts, or harmful gases. Do not install the AP in an
inflammable or explosive environment. Keep the AP away from EMI sources such as large radar stations,
radio stations, and substations. Do not subject the AP to unstable voltage, vibration, and noise.
Keep the access point at least 500 (0.31 miles) meters away from the ocean and do not face it towards the
sea breeze.
The installation site should be free from water flooding, seepage, dripping, or condensation. The installation
site should be selected according to network planning and communications equipment features, and
considerations such as climate, hydrology, geology, earthquake, electrical power, and transportation.
Please make sure that the access point and power distribution system are properly grounded.
Caution
Please follow the procedures in the user manual to install and remove the access point.
Handling Safety
Do not move the access point frequently.
Cut off all the power supplies and unplug all power cords before moving or handling the access point.
Electric Safety
Warning
Improper or incorrect electric operations may cause a fire, electric shock, and other accidents, and lead
to severe and fatal personal injury and device damage.
Direct or indirect contact with high voltage or mains power supply via wet objects may cause fatal
dangers.
Observe local regulations and specifications during electric operations. Only personnel with relevant
qualifications can perform such operations.
Check whether there are potential risks in the work area. For example, check whether the power supply is
grounded, whether the grounding is reliable, and whether the ground is wet.
Learn about the position of the indoor emergency power switch before installation. Cut off the power switch

Hardware Installation and Reference Guide Preparing for Installation
10
in case of accidents.
Check the access point carefully before shutting down the power supply.
Keep the access point far away from grounding or lightning protection devices for power device.
Keep the access point far away from radio stations, radar stations, high-frequency high-current devices, and
microwave ovens.
Laser Safety
The SFP transceiver (optional accessory) is a class A laser product.
When an SFP transceiver works, ensure that the port has been connected with a fiber-optic cable or sealed
by a plug to keep out dust and prevent it from hurting your eyes.
Do not look into any fiber port.
Note
Do not approach or look into any fiber port under any circumstances, as this may cause permanent
damage to your eyes.
2.2 Installation Environment Requirements
For normal operation and prolonged service life of the access point, the installation site must meet the following
requirements:
Bearing Requirements
Evaluate the weight of the access point and its accessories, and ensure that the installation site (wall or pole)
can bear the weight.
Ventilation Requirements
The access point adopts natural cooling. Reserve a sufficient clearance around the access point to ensure
proper ventilation.
Temperature/Humidity Requirements
To ensure the normal operation and prolonged service life of the access point, maintain an appropriate
temperature and humidity. Working in an environment with too high or too low temperature and humidity for a
long period may damage the access point.
In an environment with high relative humidity, the insulating material may have poor insulation or even leak
electricity. Sometimes it is also prone to changes in the mechanical properties and causes rusting of metal
parts.
In an environment with low relative humidity, static electricity is prone to occur and damage the internal
circuits of the access point.
A high temperature can accelerate the aging process of insulation materials, greatly reducing the reliability
of the access point and severely affecting its service life.
Before using the GE SFP transceiver (Mini-GBIC module), make sure that the ambient temperature meets
the requirement.

Hardware Installation and Reference Guide Preparing for Installation
11
Table 2-1 Working Environment Requirements
Operating Temperature
Operating Humidity
-40°C to 65°C (-40°F to 149°F)
0% to 100% RH (non-condensing)
Waterproof Requirement
Seal the unused ports using the connector plugs or cable glands to ensure that the access point is watertight.
The cable glands must be used for all cables that are threaded through the ports to prevent exposing the
access point interior to environmental elements. See Installing the Ethernet Cable for details.
Grounding Requirement
A proper grounding system is the basis for stable and reliable running and is indispensable for preventing
lightning strikes and interference. Carefully check the grounding conditions at the installation site according to
the grounding specifications, and complete grounding properly based on the actual situation.
Anti-interference Requirements
Keep the access point as far away from the lightning prevention equipment and grounding equipment of the
power device as possible.
Keep the access point far away from radio stations, radar stations, high-frequency high-current devices, and
microwave ovens.
2.3 Tools
Table 2-2 Tools
Common
Tools
Phillips screwdriver, Hex screwdriver, power cords, Ethernet cables, fastening bolts,
diagonal plier, and binding straps
Special Tools
Anti-static wrist strip, wire stripper, crimping plier, wire cutter, waterproof tape
Meters
Multimeter
Other Tools
PC, display, and keyboard
Note
The tool kit is not included in the package contents. The tool kit is customer-supplied.

Hardware Installation and Reference Guide Installing the Access Point
12
3 Installing the Access Point
Caution
Before installing the access point, make sure you have carefully read the requirements in Chapter 2.
3.1 Installation Flowchart
Start
Prepare for Installation
Site?
Install the Access Point
Adjust Orientation
Finish
Installing a Mounting Plate
Assembly on a Wall
Installing a Mounting Plate
Assembly on a Pole
(Horizontal or Vertical)
Wall Pole
Connect Cables
3.2 Before You Begin
Carefully plan and arrange the installation position, networking mode, power supply, and cabling before
installation. Confirm the following requirements before installation:
The installation site provides sufficient space for proper ventilation.
The installation site meets the temperature and humidity requirements of the access point.
The power supply and required current are available in the installation site.
The selected power supply modules meet the system power requirements.
The installation site meets the cabling requirements of the access point.
The installation site meets the site requirements of the access point.

Hardware Installation and Reference Guide Installing the Access Point
13
The customized access point meets the client-specific requirements.
3.3 Precautions
The outdoor access point can be mounted on a wall or a pole with a diameter ranging from 50 mm to 70 mm
(1.97 in. to 2.76 in.). If the diameter of the pole is out of this range, please prepare a hose clamp that can hold
the pole. The thickness of the hose clamp should be at least 2.5 mm (0.10 in.). The installation site is determined
by the technical personnel who conducts a site survey.
Please make sure that the installation site meets with the following requirements in Installation Environment
Requirements and observe the following precautions:
Do not power on the access point during installation.
Install the access point in a well-ventilated location.
Do not subject the access point to high temperature.
Keep the access point away from high voltage cables.
Do not expose the access point in a thunderstorm or strong electric field.
Cut off the power switch before cleaning the access point.
Do not open the enclosure when the access point is working.
Secure the access point tightly.
3.4 Installing the Access Point
Caution
You are advised to install the access point where you can get the optimal Wi-Fi coverage.
Images are for indicative purpose only and may not represent exact equipment.
The dimensions of the mounting arm and mounting plate assembly are shown in the following figures.
Figure 3-1 Dimensions of Mounting Arm