San Jamar C2410C User manual

C2410C EZFIT®CUP DISPENSER INSTALLATION INSTRUCTIONS
5 3/4” Dia.
146 mm
HOLE SAW RECOMMENDED
1. CUT HOLE IN COUNTER SURFACE
2. REMOVE TRIM RING TURNING
COUNTER CLOCKWISE
3. SECURE CUP DISPENSER TO COUNTER
WITH SUPPLIED SCREWS
4. SELECT PROPER SIZE GASKET FOR CUP
(SEE TABLE ON BACK)
5. INSTALL GASKET OVER POSTS IN
UNDERSIDE OF RING
6. REPLACE COVER RING WITH GASKET BY TURNING
CLOCKWISE OVER MOUNTING RING UNTIL SECURE
7. LOAD CUPS THROUGH GASKET
REPLACEMENT PARTS & ACCESSORIES see reverse side for replacement gaskets)
X24MT Black Mounting Ring (new low prole)
X24TR Black Trim Ring (new low prole)
XC24KIT Replacement Trim Rings (old & new)
C2415 Spring
C2413BK End Cap
100458BK Cup Pusher
C2412SV Wire Cage
for Surface Mount
C24XC Chrome Finish Trim Ring

SJCR México
Av. Universidad #1377-701
Colonia Axotla CP 01030
Del. Álvaro Obregón
MÉXICO, DF
T: [phone]
F: [phone]
[e-mail]
San Jamar
Chef Revival
555 Koopman Lane
Elkhorn, Wisconsin 53121
USA
T: +1.262.723.6133
F: +1.262.723.4204
[e-mail]
SJCR Europe
Schoorstraat 26A, bus-1
2220 Heist op-den Berg
BELGIUM
T: [phone]
F: [phone]
[e-mail]
SJCR Canada
3300 Bloor Street West
Center Tower, 11th Floor, Suite 3140
Toronto, ON M8X 2X3
CANADA
T: +1.416.760.7367
F: +1.416.207.2071
[e-mail] C2419_RevD
GASKET SIZING GUIDE
Approximate Cup
Size Range
Gasket
Size
Quantity
of Gaskets
in Kit
minimum maximum black white
2 7/8”(73mm) 3 1/8”(79mm) 8 oz (236mL) to 14 oz (414mL) SMALL XC2422SBK XC2422S 3
3 1/2”(89mm) 3 7/8”(98mm) 16 oz (474mL) to 24 oz (710mL) MEDIUM XC2422MBK XC2422M 3
4 3/16”(106mm) 4 3/8”(111mm) 32 oz (947mL) LARGE XC2422LBK XC2422L 3
4 1/2" (114mm) 4 3/4" (121mm) 32 oz (947mL) to 46 oz (1360mL) EXTRA LARGE XC2422XLBK XC2422XL 3
XC2426
One each-
Small,
Medium,Large,
Extra Large
4
REPLACEMENT GASKET KITS
Approximate Cup
Rim Diameter Part Numbers
1. Turn cup upside down.
2. Afx gasket over cup. Gasket
should rest about 2/3 of the
way down from rim of cup.
3. When gasket ts appropriately,
this indicates the correct
gasket size to use.
Gasket should
lie within this
range for best
cup dispensing
performance.
IS009
1.TURN CUP UPSIDE DOWN ON RULER,
WITH WIDEST POINT OF RIM TOUCHING
END OF RULER (BLACK DOT).
2. DETERMINE SIZE OF CUP RIM DIAMETER
(S, M, L, XL) BASED ON PLACEMENT OF
RIGHT SIDE OF CUP.
3. USE GASKET FOR THAT SIZE.
# OF
HOLES GASKET SIZE PART #
° SMALL XC2422S/XC2422SBK
° ° MEDIUM XC2422M/XC2422MBK
° ° ° LARGE XC2422L/XC2422LBK
° ° ° ° EXTRA LARGE XC2422XL/XC2422XLBK
PART QUANTITY
APPROXIMATE CUP APPROXIMATE CUP GASKET NUMBERS OF GASKETS
RIM DIAMETER SIZE RANGE SIZE (BLACK) (WHITE) IN KIT
REPLACEMENT GASKET KITS
MINIMUM MAXIMUM
2 7/8” (73mm) 3 1/8” (79mm) 8oz (236mL) to 14oz (414mL) SMALL XC2422SBK XC2422S 3
3 1/2” (89mm) 3 7/8” (98mm) 16oz (474mL) to 24oz (710mL) MEDIUM XC2422MBK XC2422M 3
4 3/16” (106mm) 4 3/8” (111mm) 32oz (947mL) LARGE XC2422LBK XC2422L 3
4 1/2” (114mm) 4 3/4” (121mm) 32oz (947mL) to 46oz (1360mL) EXTRA LARGE XC2422XLBK XC2422XL 3
ONE OF EACH XC2426 4
1/2’’1’’ 1 1/2’’2’’ 2 1/2’’3’’ 3 1/2’’4’’
PLACE RIM
OF CUP HERE
4 1/2’’5’’
XC2426BK
1.TURN CUP UPSIDE DOWN ON RULER,
WITH WIDEST POINT OF RIM TOUCHING
END OF RULER (BLACK DOT).
2. DETERMINE SIZE OF CUP RIM DIAMETER
(S, M, L, XL) BASED ON PLACEMENT OF
RIGHT SIDE OF CUP.
3. USE GASKET FOR THAT SIZE.
# OF
HOLES GASKET SIZE PART #
° SMALL XC2422S/XC2422SBK
° ° MEDIUM XC2422M/XC2422MBK
° ° ° LARGE XC2422L/XC2422LBK
° ° ° ° EXTRA LARGE XC2422XL/XC2422XLBK
PART QUANTITY
APPROXIMATE CUP APPROXIMATE CUP GASKET NUMBERS OF GASKETS
RIM DIAMETER SIZE RANGE SIZE (BLACK) (WHITE) IN KIT
REPLACEMENT GASKET KITS
MINIMUM MAXIMUM
2 7/8” (73mm) 3 1/8” (79mm) 8oz (236mL) to 14oz (414mL) SMALL XC2422SBK XC2422S 3
3 1/2” (89mm) 3 7/8” (98mm) 16oz (474mL) to 24oz (710mL) MEDIUM XC2422MBK XC2422M 3
4 3/16” (106mm) 4 3/8” (111mm) 32oz (947mL) LARGE XC2422LBK XC2422L 3
4 1/2” (114mm) 4 3/4” (121mm) 32oz (947mL) to 46oz (1360mL) EXTRA LARGE XC2422XLBK XC2422XL 3
ONE OF EACH XC2426 4
1/2’’1’’ 1 1/2’’2’’ 2 1/2’’3’’ 3 1/2’’4’’
PLACE RIM
OF CUP HERE
4 1/2’’5’’
XC2426BK
1.TURN CUP UPSIDE DOWN ON RULER,
WITH WIDEST POINT OF RIM TOUCHING
END OF RULER (BLACK DOT).
2. DETERMINE SIZE OF CUP RIM DIAMETER
(S, M, L, XL) BASED ON PLACEMENT OF
RIGHT SIDE OF CUP.
3. USE GASKET FOR THAT SIZE.
# OF
HOLES GASKET SIZE PART #
° SMALL XC2422S/XC2422SBK
° ° MEDIUM XC2422M/XC2422MBK
° ° ° LARGE XC2422L/XC2422LBK
° ° ° ° EXTRA LARGE XC2422XL/XC2422XLBK
PART QUANTITY
APPROXIMATE CUP APPROXIMATE CUP GASKET NUMBERS OF GASKETS
RIM DIAMETER SIZE RANGE SIZE (BLACK) (WHITE) IN KIT
REPLACEMENT GASKET KITS
MINIMUM MAXIMUM
2 7/8” (73mm) 3 1/8” (79mm) 8oz (236mL) to 14oz (414mL) SMALL XC2422SBK XC2422S 3
3 1/2” (89mm) 3 7/8” (98mm) 16oz (474mL) to 24oz (710mL) MEDIUM XC2422MBK XC2422M 3
4 3/16” (106mm) 4 3/8” (111mm) 32oz (947mL) LARGE XC2422LBK XC2422L 3
4 1/2” (114mm) 4 3/4” (121mm) 32oz (947mL) to 46oz (1360mL) EXTRA LARGE XC2422XLBK XC2422XL 3
ONE OF EACH XC2426 4
1/2’’1’’ 1 1/2’’2’’ 2 1/2’’3’’ 3 1/2’’4’’
PLACE RIM
OF CUP HERE
4 1/2’’5’’
XC2426BK
SMALL GROUPING OF HOLES ON EDGE
INDICATE GASKET SIZE SEE CHART
How to determine wHicH gasket to use