Satel PERFECTA-T Owner's manual

PROGRAMMING
perfecta-t_p_en 07/20
SATEL sp. z o.o.
ul. Budowlanych 66 • 80-298 Gdańsk • POLAND
tel. [phone]
www.satel.eu
Alarm Control Panel PERFECTA-TFirmware Version 1.04

Before you start programming, please read carefully this manual in order to avoid mistakes
that can lead to malfunction or even damage to the equipment.
SATEL aims to continually improve the quality of its products, which may result in changes in
their technical specifications and software. Current information about the changes being
introduced is available on our website.
Please visit us at:
http://www.satel.eu
Hereby, SATEL sp. z o.o. declares that the radio equipment type PERFECTA-T 32 /
PERFECTA-T 32-WRL is in compliance with Directive 2014/53/EU. The full text of the
EU declaration of conformity is available at the following internet address:
www.satel.eu/ce
Service code: 12345
The following symbols may be used in this manual:
- note,
- caution.

Changes made to the firmware version 1.04
Troubles
When “Grade 2” option is enabled, AC power loss will cause a trouble
condition if it lasts longer than 10 seconds (it has no effect on the
operation of the “19. Trouble status” type output, which is activated
immediately after AC power is lost).
Outputs
The list of troubles which can trigger the “19. Trouble status” type
output was expanded.
Reporting
New parameter:
“Interval between attempts” – defines the time between
subsequent attempts to send an event.

2 PERFECTA-T SATEL
CONTENTS
1. Introduction......................................................................................................................4
2. Configuring the system by using keypad......................................................................4
2.1 Starting the service mode....................................................................................................4
2.2 Starting the service mode “from pins” ..................................................................................4
2.3 Service mode indication.......................................................................................................5
2.4 Navigating through the menu and running functions............................................................5
2.4.1 Using the arrow keys ................................................................................................................5
2.4.2 Using the number shortcuts......................................................................................................5
2.5 Data editing.........................................................................................................................5
2.5.1 Selection from the single-choice list .........................................................................................6
2.5.2 Selection from the multiple-choice list ......................................................................................6
2.5.3 Entering decimal values............................................................................................................6
2.5.4 Entering hexadecimal values....................................................................................................6
2.5.5 Programming telephone numbers ............................................................................................6
2.5.6 Entering names.........................................................................................................................7
2.6 Hiding the service mode......................................................................................................7
2.7 Exiting the service mode......................................................................................................8
3. Configuring the system with the PERFECTA SOFT program .......................................8
3.1 Description of the PERFECTA SOFT program......................................................................8
3.1.1 Menu bar in the PERFECTA SOFT program.............................................................................8
3.1.2 Side menu.............................................................................................................................. 10
3.1.3 Additional menu ..................................................................................................................... 10
3.2 Establishing connection between the program and the control panel.................................12
4. Hardware........................................................................................................................12
4.1 Mainboard .........................................................................................................................12
4.1.1 Clock...................................................................................................................................... 13
4.1.2 Times ..................................................................................................................................... 13
4.1.3 Arming.................................................................................................................................... 13
4.1.4 Options................................................................................................................................... 14
4.2 Telephone.........................................................................................................................15
4.2.1 Options................................................................................................................................... 16
4.3 Keypad..............................................................................................................................16
4.3.1 Options................................................................................................................................... 16
4.3.2 Display and keys.................................................................................................................... 17
4.3.3 Chime..................................................................................................................................... 18
4.3.4Volume................................................................................................................................... 18
4.3.5 Wireless keypad PERFECTA-T 32-WRL............................................................................... 18
4.4 Keyfobs module.................................................................................................................18
4.5 Zone module .....................................................................................................................19
4.6 Output module...................................................................................................................20
5. Partitions........................................................................................................................20
5.1 Partition parameters..........................................................................................................20
6. Zones..............................................................................................................................22
6.1 Zone parameters and options............................................................................................22
6.2 Zone types ........................................................................................................................24
6.3 Wireless detector PERFECTA-T 32-WRL..........................................................................25
6.3.1 Wireless detectors and zone settings.................................................................................... 25
7. Outputs...........................................................................................................................26
7.1 Output functions................................................................................................................26
7.2 Output parameters and options .........................................................................................27
7.3 Quick control of outputs.....................................................................................................28

SATEL PERFECTA-T 3
7.4 Wireless siren PERFECTA-T 32-WRL...............................................................................28
8. Communication .............................................................................................................28
9. Reporting .......................................................................................................................29
9.1 Reporting parameters and options.....................................................................................29
9.1.1 Station 1 / Station 2.................................................................................................................30
9.1.2 Test transmissions..................................................................................................................30
9.1.3 Events selection......................................................................................................................31
10. Messaging......................................................................................................................31
10.1 Parameters and options of the messaging.........................................................................31
10.1.1 Phones....................................................................................................................................31
10.1.2 AUDIO messaging..................................................................................................................32
10.1.3 AUDIO messages...................................................................................................................32
11. Timers.............................................................................................................................33
11.1 Parameters and options of the timers.................................................................................33
11.1.1 Editing the timer parameters...................................................................................................34
12. Control panel firmware update.....................................................................................34
13. Users ..............................................................................................................................34
13.1 User schedules..................................................................................................................35
13.1.1 Parameters of the user schedule............................................................................................35
13.2 Default functions of keyfob buttons ....................................................................................36
14. Restoring the factory settings......................................................................................36
14.1 Restoring factory settings from keypad ..............................................................................36
14.2 Restoring factory settings from PERFECTA SOFT program................................................36
15. Manual update history ..................................................................................................37

4 PERFECTA-T SATEL
1. Introduction
You can configure the PERFECTA alarm system by using:
a computer running the PERFECTA SOFT program,
a keypad.
The control panel can be configured when the ACTIVE option is enabled (see USER MANUAL).
As required by the standards, the service access after completion of the installation
has to be limited by the administrators.
Names of parameters and options from the PERFECTA SOFT program are used in this
manual. At the description of each parameter or option, you will find one of the following data
in square brackets:
name of the function which is used for configuring a parameter or option on the keypad,
name of a parameter or option from the keypad.
2. Configuring the system by using keypad
You can configure the alarm system by using functions available in the service mode menu.
When the control panel is running in service mode, tamper alarms are not
generated.
2.1 Starting the service mode
1. Enter the service code (by default: 12345) and press .
2. User menu appears.
3. Press .
4. When the cursor shows the SERVICE MODE function, press .
5. Service mode menu will be displayed (the cursor will show the END SM function).
2.2 Starting the service mode “from pins”
When entering the service mode in the normal way is not possible (the control panel does not
support keypads, does not accept the service code, etc.), you can use the emergency
procedure, so-called, starting “from pins”.
1. Turn off the control panel power supply (first disconnect the AC power, and then the
battery).
2. Put a jumper on the RESET pins on the control panel mainboard.
3. Turn on the control panel power supply (first connect the battery and then the AC power).
4. Wait a few seconds (until LEDs next to the RESET pins stop flashing) and remove the
jumper from the RESET pins. The control panel will enter the service mode. The service
mode menu will be displayed on the wired keypad with the lowest address.
If there is no wired keypad in the alarm system or there is no communication with the
wired keypads (e.g. when the communication bus is shorted), you can get access to
the service mode menu from the wireless keypad with the lowest address. Press any
key on this keypad within 30 seconds of removing jumper from the RESET pins.
The service mode menu will not be displayed, if the DISABLE SERVICE MODE option is
enabled in the control panel. The “Factory settings ? 1=Yes” message will be

SATEL PERFECTA-T 5
displayed on the keypad with the lowest address. You can press to restore the
factory default settings. The service mode menu will not be displayed until the factory
settings are restored.
2.3 Service mode indication
The service mode is indicated on the keypads by means of the LED. The LED is
steady ON on the keypad on which the service mode menu is displayed, and is flashing on
the other keypads. Additionally, the service mode can be signaled audibly, after the
appropriate option is enabled.
2.4 Navigating through the menu and running functions
To navigate throughout the menu, you can use the arrow keys or number shortcuts. You can
also combine the two methods. The cursor shows the submenu you can enter / function
you can run.
2.4.1 Using the arrow keys
1. Using the and keys, find the required submenu.
2. Press or to open a submenu (use the key to go back to the main menu).
3. Repeat the steps 1 and 2 until the required function is found.
4. Press or to run the function.
2.4.2 Using the number shortcuts
Submenus and functions are numbered (you can find the numbers in the LIST OF SERVICE
FUNCTIONS document).
1. Use the number keys to enter the number (use the key to erase the last digit).
2. The menu item designated by this number will be displayed (use the key to go back
to the main menu).
3. Press or to open a submenu or run a function.
If the cursor indicates END SM and you want to quickly run a function, enter its number and
press or . For example, to run the expander identification function, press
successively .
If the cursor indicates an item different from END SM, entering a digit will add this digit at
the end of the number by which the item displayed in the menu is designated. New digits are
always added at the end of the number displayed (only the END SM function is not
numbered). For example, if the cursor indicates a menu item with the 31 (31.EOL) number,
pressing in turn will display the 3132 (3132.Zn.32 EOL) item, not the 32
(32.SENSITIVITY) item. To display the 32 (32.SENSITIVITY) item, you should press (to
move the cursor down) or (to erase 1 and add 2).
If you remember the submenu/function number and you want to avoid mistakes, press
before entering the number.
2.5 Data editing
The editing method depends on the type of data. Having completed the editing, press
to save the changes. If you want to exit the function without saving the changes, press .

6 PERFECTA-T SATEL
2.5.1 Selection from the single-choice list
In the lower line of the display, the currently selected item is presented. You can scroll the list
using the and keys.
2.5.2 Selection from the multiple-choice list
In the lower line of the display, one of the items you can choose from is presented. You can
scroll the list using the and keys. The following symbol is situated in the upper
right corner of the display:
–displayed item is selected / option is enabled,
–displayed item is not selected / option is disabled.
Press any number key to change the currently shown symbol for another one.
If you want to see the status of all items (these can be e.g. zones, outputs, options, etc.),
press or . The numbers around the display allow the items to be identified. Use the
and keys to move the cursor. After hovering the cursor over the selected item,
you can change its status by pressing any number key. If you want to restore the previous
way of presentation of the list, press or .
2.5.3 Entering decimal values
To enter digits, use the number keys. Use the and keys to move the cursor. In
some functions, the key deletes the character on the left side of the cursor.
2.5.4 Entering hexadecimal values
To enter digits, use the number keys. To enter the A, B and C characters, use the key,
and to enter D, E and F, use the key (keep pressing the key until the required character
appears). Use the and keys to move the cursor. The key deletes the
character on the left side of the cursor.
2.5.5 Programming telephone numbers
The characters that can be entered by using the keys are presented in Table 1. Keep
pressing the key until the required character appears.
Use the and keys to move the cursor. The key deletes the character on the
left side of the cursor.
Key
Characters available after next keystroke
1
2
B
C
a
b
c
3
D
E
F
d
4
5
6
7
8
9
0
#
Table 1. Characters available in the keypad when entering telephone numbers.

SATEL PERFECTA-T 7
Special character
Function description
B
switch-over to pulse dialing
C
switch-over to tone dialing (DTMF)
D
waiting for additional signal
E
3 second pause
F
10 second pause
signal in DTMF mode
#
signal # in DTMF mode
a
b
c
d
other signals generated in DTMF mode
Table 2. Special character functions.
2.5.6 Entering names
The characters that can be entered by using the keys are presented in Table 3. Keep
pressing the key until the required character appears. Long press the key to display the digit
assigned to it.
Shown on the right side in the upper line of the display is information about the letter case:
[ABC] or [abc] (it will be displayed after pressing any key and will be visible for a few seconds
after the last keystroke).
Use the and keys to move the cursor. The key deletes the character on the
left side of the cursor.
Key
Characters available after next keystroke
!
?
'
`

"
{
}
$
%
&
@
\
^
|
#
1
a
b
c
2
d
e
f
3
g
h
i
4
j
k
l
5
m
n
o
6
p
q
r
s
7
t
u
v
8
w
x
y
z
9
.
,
:
;
+
-
/
=
_
<
>
(
)
[
]
0
Table 3. Characters available when entering names. The upper case letters are available
under the same keys (to change the letter case, press ).
2.6 Hiding the service mode
You can hide the service mode by using the 09.HIDE SM function. The control panel will
remain in the service mode, but the service mode menu will not be displayed. The function
can be useful e.g. when you have to leave the keypad, but you want to prevent unauthorized

8 PERFECTA-T SATEL
personnel from getting access to the service menu in the meantime. To get access to the
menu again, proceed in the same way as when entering the service mode.
2.7 Exiting the service mode
Keep pressing until the cursor indicates the SM END function, and then press .
3. Configuring the system with the PERFECTA SOFT program
You can download the PERFECTA SOFT program from the www.satel.eu website.
Required program version: 1.05 (or newer).
Communication between the program and the control panel is encrypted. You can program
the control panel from a computer connected to the RS-232 (TTL) port on the control panel.
3.1 Description of the PERFECTA SOFT program
Access to the program can be password protected (see ““Configuration” window” p. 11).
Fig. 1. PERFECTA SOFT window when the program is run for the first time.
3.1.1 Menu bar in the PERFECTA SOFT program
The menu bar is displayed in the top part of the program window. Appearance of the menu
bar depends on the contents presented in the window.

SATEL PERFECTA-T 9
Menu bar in the “Projects” tab
Fig. 2. Appearance of the menu bar when the “Projects” tab is displayed.
The search field is displayed on the menu bar. If you want to find a project file, click on the
search field and start entering characters. The current view will be filtered out, based on the
text entered.
Buttons
click, if the files are to be sorted by name (the arrow next to the button indicates
whether the files from A to Z or from Z to A are displayed)
click, if the files are to be sorted by the time they were saved to disk (the arrow next to
the button indicates whether the files are displayed in the descending or ascending
order)
click, if the information about files is to be presented in brief version
click, if the information about files is to be presented in full version
click to display additional menu.
Appearance of the menu bar when displaying the control panel data
Fig. 3. Appearance of the menu bar after establishing connection with the control panel.
type of alarm control panel and firmware version.
icon displayed when the control panel is running in the service mode.
date and time according to the control panel clock.
number of the COM port of the computer used for communication with the control panel.
Buttons
click to display the list of troubles. The button is shown when the control panel is
indicating a trouble or trouble memory.
click to write computer clock time to the control panel.
click to establish connection to the control panel. The button is displayed when the
program is not connected to the control panel.
click to finish connection to the control panel. The button is displayed when the
program is connected to the control panel.
click to read data from the control panel.
click to write data to the control panel.

10 PERFECTA-T SATEL
click to display information on the status of partitions, zones, outputs etc. The button
is active after connection to the control panel is established.
click to display additional menu.
3.1.2 Side menu
The side menu is displayed on the left side of the program window. Appearance of the menu
depends on the contents presented in the window.
The side menu before the control panel data are displayed
New –click to display the “New” tab.
Projects –click to display the “Projects” tab.
Import –click to import the file with control panel settings.
Recent –the list of recently opened files. Click on the name of the file to open it.
“New” tab
The tab displays the files with default settings of the PERFECTA series control panels.
“Projects” tab
The tab displays the files saved to the computer disk, containing data of the PERFECTA
series control panels.
The side menu after the control panel data are displayed
After the file with control panel data is opened or connection with the control panel is
established, the side menu will display buttons which open the tabs used for configuration of
the control panel settings.
3.1.3 Additional menu
The additional menu is displayed after you click on . Appearance of the menu depends on
the contents presented in the window.
Open –click to display the “Projects” tab.
Save –click to save the control panel data to the computer disk.
Export –click to export the file with control panel data.
Convert –click to convert the control panel data for the needs of another PERFECTA control
panel.
Connection –click to open the “Connection” window.
Configuration –click to open the “Configuration” window.
About –click to display information about the PERFECTA SOFT program.
Licence agreement –click to show the license agreement.
“Connection” window
This window allows you to configure the settings for control panel programming.
Local connection
RS-232 port –COM port of the computer through which communication with the RS-232
(TTL) port of the control panel is to take place.
Panel key –identifier of the control panel. It must be identical to that programmed in the
control panel (see p. 28).

SATEL PERFECTA-T 11
Buttons
OK –click to confirm the changes.
Cancel –click to close window without saving changes.
Fig. 4. “Connection”window.
“Configuration” window
Fig. 5. “Configuration” window.
PERFECTA Soft password –if you want to protect the program against unauthorized
access, you can enter the password.
Data files encryption key –if you want the files saved to disk to be additionally encrypted,
enter the file encryption key. Opening the files in another PERFECTA SOFT program
without entering the valid key will be impossible.
Data folder –you can choose whether the control panel data files are to be saved to the
default folder or a folder selected by you.
Program language –you can select a program language. The program will restart after the
language is changed
Buttons
Save –click to save changes.

12 PERFECTA-T SATEL
Cancel –click to close window without saving changes.
3.2 Establishing connection between the program and the control panel
Establishing connection is possible, if an identical PANEL KEY has been programmed in
the control panel and in the program, except for the control panel with factory settings.
1. Connect the control panel RS-232 (TTL) port with the computer port (for example, by
means of the USB-RS converter offered by SATEL).
2. Open the file with control panel data (the file with default settings (“New” tab) or the file
saved on the computer disk (“Projects” tab)).
3. Configure the settings required to establish connection (see ““Connection” window” p. 10).
4. Click on the menu bar.
5. A window will open with information that connection has been established and a prompt to
read the data.
6. Click “Yes”.
4. Hardware
The control panel has a built-in analog telephone communicator. To the control panel
communication bus, you can connect additional devices that will be needed in the alarm
system (keypads, zone modules and output module). The PERFECTA-T 32-WRL control
panel also supports wireless keypads.
4.1 Mainboard
Fig. 6. “Mainboard” tab.

SATEL PERFECTA-T 13
4.1.1 Clock
Daylight saving time [061.DST] –the control panel can automatically adjust the clock
settings due to a change from the summer time to the winter time and vice versa. The
following correction schemes are available:
–no correction,
–according to the European Union rules,
–according to the United States' rules,
–correction by 1 hour according to dates,
–correction by 2 hours according to dates.
Summer time from [062.Summer from] / Winter time from [063.Winter from] –if the control
panel clock is to be corrected by 1 or 2 hours according to dates, you should enter the
dates (day, month) after the clock is changed to the summer time (moved forward) or to
the winter time (moved back).
Clock correction [065.RTC adjust.] –if accuracy of the control panel clock is insufficient, its
settings can be automatically corrected (by up to ±127 seconds per week).
4.1.2 Times
AC loss report delay [123.Max.AC loss] –time during which the control panel must be
without AC power before the AC power trouble is saved to the event log and reported to
the monitoring station. If you program 0, the AC trouble will neither be saved to the event
log nor reported to the monitoring station.
Keypad's alarm time [124.Al.duration] –duration of alarm signaling on keypads.
Hide arm state indication after [125.Suppr.arm] –time counted from the moment of
partition arming, after which the LED on keypad indicating the partition armed status goes
off. If value 0 is programmed, the LED will be ON always when the partition is armed.
4.1.3 Arming
Prevent arming if not ready [Check if ready] –if this option is enabled, the control panel will
perform a check during arming for any problems that may prevent arming the system.
These include:
–a zone with PRIORITY option is violated in the partition,
–the 3. INSTANT, 4. DOUBLE KNOCK, 5. 24H BURGLARY, 7. 24H PANIC, 8. 24H PANIC SILENT,
9. 24 MEDICAL or 10. 24H FIRE type zone is violated in the partition which is to be armed,
–the 3. INSTANT, 4. DOUBLE KNOCK, 5. 24H BURGLARY, 7. 24H PANIC, 8. 24H PANIC SILENT,
9. 24 MEDICAL or 10. 24H FIRE type zone or a zone with enabled PRIORITY option is
bypassed in the partition,
–there is a tamper in the partition,
–there is a trouble in the system.
The control panel checks the conditions twice:
before starting the arming procedure –the control panel will not start the arming
procedure, if any problems occur (the keypad provides a forced arming option –see
USER MANUAL),
after finishing the exit delay countdown –the system will not be armed (the arming
procedure will end in failure), if there are any problems, which did not occur before
starting the exit delay countdown.
If the option is enabled and a zone of the 0. ENTRY/EXIT, 1. ENTRY/EXIT FINAL or 2. INTERNAL
type is violated at the moment the exit delay countdown expires and the partition is armed,
a warning alarm will be triggered. If the partition is not armed after exit delay countdown
expires, the warning alarm will not be triggered.

14 PERFECTA-T SATEL
Arm even if not ready after exit delay [Arm ExDly w.trbl] –if this option is enabled, the
control panel will not check conditions after finishing the exit delay countdown (it will only
check the conditions before starting the arming procedure). The option is available, when
the PREVENT ARMING IF NOT READY option is enabled.
Do not arm if battery trouble [BAT low = no arm] –if this option is enabled, forced arming
will be impossible in the event of battery trouble. The option is available, when the
PREVENT ARMING IF NOT READY option is enabled.
Do not arm if tampered [Tamper = no arm] –if this option is enabled, forced arming will be
impossible in the event of tamper. The option is available, when the PREVENT ARMING IF NOT
READY option is enabled.
4.1.4 Options
Service Mode beep [SM sounds] –if this option is enabled, the service mode will be audibly
signaled on the keypad.
Signal trouble state in partial arming [Trbl.in part.arm] –if this option is enabled, the
LED on the keypad goes off after both partitions are fully armed. If the option is disabled,
the LED goes off after just one of the partitions is armed in any mode.
Lock after three incorrect codes [3wrng.codes=blk.] –if the option is enabled, after
entering an incorrect code three times, the keypad will be blocked for 90 seconds. Entering
an invalid code again will prolong the locking.
Entering an invalid code three times may trigger alarm (cf. the keypad ALARM 3
INCORRECT CODES option).
Trouble memory [Troubles memory] –if this option is enabled, the control panel will also
provide information about troubles that do not exist any more. You can clear the trouble
memory by using keypad (when exiting the trouble review function) or PERFECTA SOFT
program. Additionally, the option affects the audible indication of trouble on the keypad:
–option disabled –the trouble is audibly indicated until restore,
–option enabled –the trouble is audibly indicated until review by using the 7.TROUBLES
user function (the user must press to quit the function) or trouble memory clearing
by using the PERFECTA SOFT program.
Zone restore events [Restore events] –when this option is enabled, information about zone
restore is saved in the event log, if zone triggered alarm.
Limit number of events [Events limitat.] –if the option is enabled, events from the same
source are saved into the event log 3 times only. This option does not apply to the alarms
from zones.
Grade 2 [Grade 2] –if the option is enabled, the system operates in accordance with the
EN 50131 standard requirements for Grade 2, i.e.:
–the keypad does not audibly signal alarms and troubles/troubles memory,
–the LEDs on the keypad indicates alarms only after the user enters the code and
presses ,
–the LED on the keypad goes off after just one of the partitions is armed in any
mode,
–the flashing LED in keypad means that there is a trouble in the system, some zones
are bypassed, or there has been an alarm,
–the keypad does not display alarm messages,
–the keypad display cannot be switched over to the zone status presentation mode,
–the quick arming from keypad (without entering the code) is not available,
–new access codes in the system must be composed of at least 5 digits,

SATEL PERFECTA-T 15
–partial entering of the code is interpreted as entering an incorrect code,
–the keypad will be blocked after entering an incorrect code three times (cf. BLOCK AFTER
THREE INCORRECT CODES option),
–during arming, the control panel checks for problems that prevent arming (cf. PREVENT
ARMING IF NOT READY option),
–ARM EVEN IF NOT READY AFTER EXIT DELAY, DO NOT ARM IF BATTERY TROUBLE and DO NOT
ARM IF TAMPERED options are interpreted as disabled,
–control panel gives information about past troubles (cf. TROUBLE MEMORY option),
–tamper of zone or expander can only be signaled by the external siren when the
partition to which the zone or expander belong is armed,
–the number of alarms from the 7. 24H PANIC and 8. 24H PANIC SILENT zones is not limited
(AUTO-RESET 3 option is ignored),
–arming is impossible, if the 6. 24H TAMPER zone is violated (cf. PRIORITY option),
–the warning alarm feature is enabled and the warning alarm is being signaled for at
least 30 seconds (cf. WARNING TIME),
–countdown of ENTRY DELAY, DELAY and DELAY ACTIVATION TIME is running for up to 45
seconds,
–AC power loss will cause a trouble condition if it lasts longer than 10 seconds (it has no
effect on the operation of the 19. TROUBLE STATUS type output, which is activated
immediately after AC power is lost),
–AC loss report delay can be up to 60 minutes.
Tamper alarm on internal sirens [Tmp.on int.siren] –if this option is enabled, the
1. INTERNAL SIREN output is additionally activated after triggering tamper alarm.
Tamper alarm on external sirens [Tmp.on ext.siren] –if this option is enabled, the
1. EXTERNAL SIREN output is additionally activated after triggering tamper alarm.
Backlight off on AC loss [No AC=no bcklght] –if the option is enabled, the backlight in
hardwired keypads is automatically switched off in case of 230 VAC power loss.
Disable Service Mode [Block SM] –if this option is enabled, the emergency procedure of
entering the service mode (“from pins”) is not available (it can only be used if factory
default settings of the control panel are restored).
Do not report wireless system jamming [No jamm. trouble] –if this option is enabled,
jamming of the wireless system will not be reported.
4.2 Telephone
Fig. 7. “Telephone” tab.
Tel. line loss report delay [172.TL loss dly] –time during which abnormal voltage must be
on the telephone line for the control panel to report the telephone line trouble. A delay in
reporting the trouble prevents sending information about short-time voltage dips (e.g.
during a phone call) or decays.

16 PERFECTA-T SATEL
4.2.1 Options
Tone dialing [Tone dialing] –if the option is enabled, the control panel will tone dial the
telephone numbers (pulse dial, if this option is disabled).
Pulse 1/1.5 (off 1/2) [Pulse 1/1.5] –this option applies to pulse dialing. Before you enable it,
make yourself familiar with the valid standard of pulse dialing.
No dial tone test [No dialtone test] –if the option is enabled, the control panel will not
perform the test for dial tone before dialing the number and will start dialing the number 5
seconds after going “off hook”. This makes it possible for the control panel to dial the
number when some non-standard tones occur on the telephone line after going off hook
(e.g. interrupted tone). When this option is disabled, the control panel will start dialing the
number 3 seconds after going off hook, provided that the dial tone is present.
No answer test [No answer test] –if this option is enabled, the voice message will be
played back during notification 15 seconds after dialing the number is finished (the control
panel does not perform any test for the off-hook tone).
4.3 Keypad
Name [28.Names] –individual name of the keypad (up to 16 characters).
Alarm in part. [22.Partitions] –the partition in which alarm will be triggered in the event of
keypad tamper (opening of enclosure or loss of communication).
4.3.1 Options
Fig. 8. Tab with settings for the wired keypad.

SATEL PERFECTA-T 17
Show partition 1 status [Show part.1] –if this option is enabled, the keypad LEDs and
display indicate the status of partition 1. The keypad will indicate the status of partition 2
only after entering code by the user who has access to partition 2.
Show partition 2 status [Show part.2] –if this option is enabled, the keypad LEDs and
display indicate the status of partition 2. The keypad will indicate the status of partition 1
only after entering code by the user who has access to partition 1.
Quick arm - partition 1 [Quickarm part.1] –if this option is enabled, quick arming (without
user authorization) of the partition 1 is possible.
Quick arm - partition 2 [Quickarm part.2] –if this option is enabled, quick arming (without
user authorization) of the partition 2 is possible.
Show code entering [Show code enter.] –if this option is enabled, entering the code is
presented on the keypad display by asterisks.
Quick control [Quick control] –if this option is enabled, the users can control the outputs by
using the number keys. The 15. CONTROLLED outputs must be assigned to the keys (see:
“Quick control of outputs” p. 28).
Key 7 - troubles review [Troubles review] –if this option is enabled, the users can press
and hold down for 3 seconds to view the troubles.
Key 8 - chime on/off [Chime on/off] –if this option is enabled, the chime signal can be
enabled/disabled by means of the key (the key is to be pressed and hold down for
about 3 seconds).
Key 9 - change disp. mode [Disp.mode change] –if this option is enabled, the users can
use the key to toggle between the normal display mode and the zone presentation
mode (the key is to be pressed and hold down for about 3 seconds). The option is not
available for the wireless keypad.
Alarm 3 incorrect codes [3 wrng codes al.] –if this option is enabled, entering incorrect
code three times will trigger the alarm.
MEDICAL alarm [Medical alarm] –if this option is enabled, pressing the key for approx.
3 seconds will trigger the medical (auxiliary) alarm.
FIRE alarm [Fire alarm] –if this option is enabled, pressing the key for approx. 3
seconds will trigger the fire alarm.
PANIC alarm [Panic alarm] –if this option is enabled, pressing the key for approx. 3
seconds will trigger the panic alarm.
Silent PANIC [Silent panic] –if this option is enabled, the panic alarm triggered from the
keypad will be a silent one, i.e. the keypad will not indicate it, there will be no audible
signal, but the alarm will be reported to the monitoring station. The silent panic alarm is
useful when the control panel is sending events to the monitoring station, but unauthorized
persons should not be aware of the alarm being triggered. The option is available, if the
PANIC ALARM option is enabled.
4.3.2 Display and keys
Date/time format [210.ClockFormat] –mode of presentation of time and date on the display.
LCD backlight [26.LCDbacklight] –mode of keypad display backlighting.
Keypad backlight [27.KEYbacklight] –mode of keypad keys backlighting.
Backlighting of the display and keys on the wireless keypad works differently than that
on the wired keypad (see PRF-LCD-WRL keypad manual).
Auto backlight [29. Autolight] –if the backlight of display or keys goes on automatically, you
can define whether and what event will additionally turn on the backlighting:
Not present –backlighting will be turned on only by pressing any key.

18 PERFECTA-T SATEL
Zone violation –backlighting will be turned on additionally in the event of zone violation
(select the zone).
Entry delay in part. –backlighting will be turned on additionally in the event of starting the
entry delay countdown in the partition (select the partition).
The AUTO BACKLIGHT parameter is not available for the wireless keypad.
4.3.3 Chime
The keypad can audibly signal violation of selected zones.
The wireless keypad signals the CHIME from zones not more frequently than once
every 30 seconds. In the inactive mode, the CHIME from zones is only signaled if
WAKE-UP DURATION is different from 0.
4.3.4 Volume
[251.Keys] –volume level of the beeps generated during keypad operation (key
pressing, confirmation of performed operation, etc.).
[252.Chime] –volume level of the beeps generated after zone violation (CHIME).
[253.Entry delay] –volume level of the entry delay beeps.
[254.Exit delay] –volume level of the exit delay beeps.
[255.Fire alarm] –volume level of the fire alarm beeps.
[256.Burg.alarm] –volume level when signaling burglary, panic and medical (auxiliary)
alarms.
[257.Warn.alarm] –volume level when signaling warning alarms.
[258.New trouble] –volume level when signaling troubles.
4.3.5 Wireless keypad PERFECTA-T 32-WRL
For the wireless keypad, additional parameters and options are available.
Filter [1272.Filter] –the time counted from receiving of the transmission from the keypad.
After it has elapsed and no other transmission is received, trouble will be reported.
Wake-up duration [213.Wake up] –maximum length of time for which the active mode can
be started automatically. If you enter a value different from 0:
–the active mode will be started automatically when entry or exit delay countdown has
begun, the system has been armed, or alarm has been triggered,
–the CHIME from zones will also be signaled in the inactive mode.
If you enter 0, the active mode will not be started automatically.
If the WAKE-UP DURATION is different from 0, the keypad will be awaiting for
transmissions with information on events. As a result, the energy consumption will be
growing and the battery life will be considerably reduced.
Wireless keypad initial greeting [218.Connect msg] –message displayed on the
PRF-LCD-WRL keypad after wake-up. The message is the same for all keypads.
4.4 Keyfobs module
Name [287.Ex.07 name] –individual name of the module (up to 16 characters).
Alarm in part. [227.Ex.07 part] –partition in which alarm will be triggered in the event of
module tamper.