Satel PERFECTA-IP-32 User guide

INSTALLER
MANUAL
perfecta-ip_i_en 07/20
SATEL sp. z o.o.
ul. Budowlanych 66 • 80-298 Gdańsk • POLAND
tel. [phone]
www.satel.eu
Alarm Control Panel PERFECTA-IP
Firmware Version 1.04

IMPORTANT
The security alarm system should be installed by qualified personnel.
Prior to installation, please read carefully this manual in order to avoid mistakes that can lead
to malfunction or even damage to the equipment.
Disconnect power before making any electrical connections.
Changes, modifications or repairs not authorized by the manufacturer shall void your rights
under the warranty.
SATEL aims to continually improve the quality of its products, which may result in changes in
their technical specifications and software. Current information about the changes being
introduced is available on our website.
Please visit us at:
http://www.satel.eu
Hereby, SATEL sp. z o.o. declares that the radio equipment type PERFECTA-IP 32 /
PERFECTA-IP 32-WRL is in compliance with Directive 2014/53/EU. The full text of the
EU declaration of conformity is available at the following internet address:
www.satel.eu/ce
The following symbols may be used in this manual:
- note,
- caution.

CONTENTS
1. Introduction........................................................................................................................2
2. Features..............................................................................................................................2
3. Keypads..............................................................................................................................4
3.1 Keypads features.....................................................................................................................4
4. Expansion modules...........................................................................................................4
5. MICRA wireless devices PERFECTA-IP 32-WRL ............................................................5
6. System installation............................................................................................................5
6.1 Installation plan........................................................................................................................5
6.2 Estimation of the system current consumption ........................................................................6
6.3 Cabling.....................................................................................................................................6
6.4 Installation of control panel ......................................................................................................6
6.4.1 Description of the mainboards.....................................................................................................7
6.5 Connecting devices to the communication bus........................................................................8
6.5.1 Connecting keypads....................................................................................................................8
6.5.2 Connecting 433 MHz keyfobs receiver expansion module PERFECTA-IP 32.........................10
6.5.3 Connecting the hardwired zone expanders...............................................................................10
6.5.4 Connecting the hardwired output expander..............................................................................12
6.6 Connecting detectors and other devices to the zones...........................................................12
6.7 Connecting the sirens ............................................................................................................15
6.8 Connecting the Ethernet network...........................................................................................16
6.9 Connecting the power supply and starting the control panel .................................................16
6.9.1 Main power supply.....................................................................................................................16
6.9.2 Backup power supply................................................................................................................17
6.9.3 Control panel power-up / start-up procedure ............................................................................17
6.9.4 Starting the service mode..........................................................................................................17
6.9.5 Emergency procedure of the control panel start-up..................................................................18
6.9.6 First steps after starting-up the control panel............................................................................18
6.10 Programming addresses for the hardwired keypads..............................................................18
6.10.1 Programming the address by means of the service function....................................................19
6.10.2 Programming the address without entering the service mode..................................................19
6.11 Identification of devices connected to the bus .......................................................................19
6.11.1 Starting the identification function from keypad ........................................................................19
6.11.2 Starting the identification function from PERFECTA SOFT program.........................................20
6.12 Connecting the computer to the control panel .......................................................................20
6.13 Installation of MICRA wireless devices PERFECTA-IP 32-WRL...........................................20
6.13.1 Adding new wireless devices ....................................................................................................21
6.13.2 Removing wireless devices.......................................................................................................22
7. Numeration of zones and outputs in the system..........................................................23
7.1 Numeration of zones..............................................................................................................23
7.1.1 Hardwired zones........................................................................................................................23
7.1.2 Wireless zones PERFECTA-IP 32-WRL...................................................................................23
7.2 Numeration of outputs............................................................................................................23
7.2.1 Hardwired outputs .....................................................................................................................23
7.2.2 Wireless outputs PERFECTA-IP 32-WRL.................................................................................23
8. Specifications ..................................................................................................................23
8.1 Control panel..........................................................................................................................23
8.2 PRF-LCD keypad...................................................................................................................25

2 PERFECTA-IP SATEL
1. Introduction
This manual describes the PERFECTA-IP 32 and PERFECTA-IP 32-WRL control panels and
how it should be installed. In addition, the manual provides information about devices
compatible with the control panel and how they are to be connected.
The PERFECTA-IP series alarm control panels meet the requirements of the following
standards: EN 50131-1 Grade 2, EN 50131-3 Grade 2, EN 50131-6 Grade 2, EN 50130-4
and EN 50130-5 Class II.
2. Features
System structure
•2 partitions (group of zones).
•Each zone can be assigned to two partitions.
Zones
•8 programmable hardwired zones on the control panel mainboard:
– support for NO and NC type detectors, as well as roller shutter and vibration detectors,
– support for Single EOL and Double EOL configuration.
•Electrical protection of all zones.
•Maximum number of programmable zones: 32.
•20 zone types.
Outputs
•4 programmable hardwired outputs on the control panel mainboard:
– 2 high-current outputs,
– 2 low-current outputs, OC type.
•Maximum number of programmable outputs:
– 12 (PERFECTA-IP 32),
– 16 (PERFECTA-IP 32-WRL) – outputs with numbers from 13 to 16 are dedicated
outputs for operating the MSP-300 wireless sirens.
•23 performed functions.
•2 power supply outputs on the control panel mainboard.
•Electrical protection of all outputs.
Communication bus
•Capability to connect keypads and expansion modules.
•Electrical protection of communication bus.
Wireless devices only PERFECTA-IP 32-WRL
•Support for 433 MHz radio devices manufactured by SATEL:
– up to 32 detectors,
– up to 4 sirens,
– up to 4 keypads,
– up to 15 keyfobs.
•Encrypted radio communication.
•Two-way communication with wireless keypads and sirens.

SATEL PERFECTA-IP 3
•Up to 6 control functions available from keyfob.
Communication
•Built-in Ethernet module.
Reporting
•Reporting events to two monitoring stations.
•Support for Contact ID and SIA communication formats.
•Sending event codes to the monitoring station via Ethernet.
Messaging
•Informing users of the PERFECTA CONTROL application about events using push
notifications.
PERFECTA CONTROL mobile application
•Operating the alarm system from mobile devices:
– control of the alarm system,
– checking the alarm system status.
Event log
•3584 events.
Users
•15 users.
•Capability to assign to the user:
– code,
– keyfob.
•Authority level determining the scope of access to the system.
Timers
•8 timers to automatically:
– arm/disarm the partitions,
– control the outputs (switching the lights on/off, watering the garden, etc.).
Programming
•Local programming:
– keypad,
– computer with the PERFECTA SOFT program installed, connected to the control panel
RS-232 (TTL) port.
•Remote programming using a computer with PERFECTA SOFT program installed, via
Ethernet.
Control panel firmware update
•Local update using a computer connected to the RS-232 (TTL) port of the control panel.
•Remote update using the UPSERV update server via Ethernet.
Built-in power supply
•Switching-mode power supply 12 V / 2 A.
•Short-circuit protection.
•Battery status monitoring and low battery cut-off circuit.

4 PERFECTA-IP SATEL
3. Keypads
Fig. 1. PRF-LCD / PRF-LCD-WRL keypad.
SATEL offers the following keypads for PERFECTA-IP alarm control panels:
PRF-LCD – hardwired LCD keypad with mechanical keys,
PRF-LCD-WRL – wireless LCD keypad with mechanical keys (supported by
PERFECTA-IP 32-WRL control panel).
The alarm system should include at least one keypad.
The wireless keypads respond to the user actions more slowly than the wired ones.
3.1 Keypads features
•Display 2 x 16 characters with backlight.
•LEDs indicating the status of the partitions and the system.
•12 keys, bearing designations according to telephone standard and intended for entering
data.
•4 additional keys for menu navigation and arming/disarming.
•Backlit keys.
•Tamper contact reacting to the enclosure opening or detaching from the wall.
4. Expansion modules
You can connect to the control panel the following expanders:
INT-RX-S – 433 MHz keyfobs receiver expansion module. Enables users to control the alarm
system using the 433 MHz keyfobs. only PERFECTA-IP 32
INT-E – zone expander. Adds 8 programmable hardwired zones to the security system.
INT-O / INT-ORS – output expander. Adds 8 programmable hardwired outputs to the security
system.

SATEL PERFECTA-IP 5
5. MICRA wireless devices PERFECTA-IP 32-WRL
The PERFECTA-IP 32-WRL control panel supports the following MICRA (433 MHz) wireless
devices:
MFD-300 – wireless water flood detector.
MGD-300 – wireless glass-break detector.
MMD-300 – wireless magnetic contact.
MMD-302 – wireless magnetic contact with input for roller shutter detector.
MPD-300 – wireless passive infrared detector.
MPD-310 – wireless passive infrared detector.
MPD-310 Pet – wireless passive infrared detector with pet immunity up to 20 kg.
MRU-300 – radio signal repeater.
MSD-300 – wireless smoke and heat detector.
MSD-350 – wireless smoke detector.
MSP-300 – wireless outdoor siren.
MXD-300 – wireless multipurpose detector.
PRF-LCD-WRL – wireless keypad.
The MPD-310 and MPD-310 Pet detectors are identified as the MPD-300 detector.
The MSD-350 detector is identified as the MSD-300 detector.
The MXD-300 detector is identified as the MMD-302 detector.
The MRU-300 repeater is identified as the MMD-300 detector. When registering the
repeater to the control panel and configuring it, proceed in the same way as with
a detector. You do not have to register the repeater to the control panel but its
operation will not be supervised if unregistered (power failures, lack of presence or
tamper will not be reported).
6. System installation
Disconnect power before making any electrical connections.
The following tools will be useful during installation:
•blade screwdriver 2.5 mm,
•Phillips screwdriver,
•precision pliers,
•flat nose pliers,
•drill with a set of drill bits.
6.1 Installation plan
The installation must be preceded by preparation of a plan of the security alarm system. It is
advisable to draw up a sketch of the premises and mark on it all the devices that are to be
included in the alarm system: control panel, keypads, detectors, sirens, expansion modules
etc. The control panel and other alarm system components should be installed within the
protected area.

6 PERFECTA-IP SATEL
When planning the installation location for the PERFECTA-IP 32-WRL control panel and
MICRA wireless devices, you must take into consideration the range of radio communication.
Remember that thick walls, metal partitions, etc. will reduce the range of the radio signal.
6.2 Estimation of the system current consumption
At the security system planning stage you should sum up the currents consumed by all
devices included in the system (control panel mainboard, keypads, expansion modules,
detectors, sirens, etc.). The calculation should take into account the battery charging current.
If the sum of currents exceeds the maximum output current of the control panel power
supply, expander with power supply or an additional power supply unit should be used.
The sum of currents consumed by the devices connected to the power supply unit (expander
with power supply) must not exceed the power supply output current.
If you plan to connect devices to particular power outputs (of the control panel, expander with
power supply, etc.), remember that the sum of currents consumed by these devices must not
exceed the maximum current carrying capacity of those outputs.
6.3 Cabling
It is recommended that an unshielded non-twisted cable be used for making electric
connections between devices included in the system.
If you use the twisted-pair type of cable, remember that CLK (clock) and DTA (data)
signals must not be sent through one pair of twisted conductors.
Select cross-section of the power supply wires so that the supply voltage drop between the
power supply and the supplied device should not exceed 1 V as against the output voltage.
In order to guarantee correct functioning of the system components it is important that
resistance and capacitance of the signal wires be as low as possible. When the distances
between the devices are greater, several wires connected in parallel may have to be used for
each signal, in order to reduce conductor resistance. This, however, may lead in
consequence to an increase in conductor capacitance. Too high resistance or capacitance of
the cables connecting the control panel to keypads or expansion modules can prevent the
devices from working correctly (e.g. the control panel will be unable to identify devices,
absence of devices will be reported, etc.). When selecting the length of cables, follow
recommendations set out in sections on connection of particular types of devices.
Avoid running the cables in parallel to or in close vicinity of the 230 VAC wires, as this may
result in malfunctioning of the system.
6.4 Installation of control panel
The control panel mainboard contains electronic components sensitive to
electric charges.
Before connecting the mainboard to power supply source (battery, alternating
voltage from transformer), you must first complete all the installation work with
hardwired devices (connection of keypads, expansion modules, detectors etc.).
The control panel should be installed indoors, in spaces with normal humidity of air. The
control panel must be protected against unauthorized access. The installer should provide
protection for the users and service personnel by using a suitable device enclosure.
A 230 VAC power supply circuit with protective grounding must be available at the control
panel installation place.

SATEL PERFECTA-IP 7
6.4.1 Description of the mainboards
Fig. 2. Mainboard of the control panel.
LED indicators:
left – not used.
center – ON when the battery is being tested.
right – not used.
RESET pins for emergency starting the control panel (see: “Emergency procedure of the
control panel start-up” p. 18).
RS-232 (TTL) port.
battery connection cables (red +, black -).
LED indicators:
E1 – ON when the control panel is powered on; flashes during communication over the
network with PERFECTA Soft program or PERFECTA Control app.
E2 – not used.
RJ-45 connector for Ethernet network. It is provided with two LEDs:
green – ON when the control panel is connected to the network,
yellow – flashes during data transmission.
wireless system module. only PERFECTA-IP 32-WRL
Description of terminals
AC - power input (18 VAC).

8 PERFECTA-IP SATEL
+OUT1-, +OUT2-- programmable high-current outputs. +12 VDC voltage is always present
at the “+” terminal. The “–” terminal is either shorted to or disconnected
from the common ground, depending on the output status
(active/inactive) and polarity.
OUT3, OUT4 - programmable low-current outputs, OC type (disconnected from
common ground / shorted to common ground).
COM - common ground.
AUX - +12 VDC power output.
KPD - +12 VDC power output.
DTA - communication bus data.
CLK - communication bus clock.
Z1...Z8- zones.
6.5 Connecting devices to the communication bus
The bus wires must be run in one cable.
The total length of the expander bus may not exceed 600 m.
The device can be powered directly from the control panel, if the distance to the
control panel does not exceed 300 m. Where the distance is greater, another power
source must be provided for the device (power supply or expander with power supply).
The Table 1 shows the number of wires required for correct connection of the device to the
expander bus if conductors with 0.5 mm diameter are used.
CLK
DTA
COM
Distance
Number of wires
up to 300 m
1
1
1
300-600 m
2
2
2
Table 1.
For most devices to be connected to the communication bus, setting of a suitable address is
required. Two devices must not share the same address (otherwise their identification will be
impossible). For information on the requirements related to address setting, please refer to
the sections describing how specific devices are to connected.
6.5.1 Connecting keypads
The control panel supports up to 4 keypads. These can be either wired or wireless keypads
(the wireless ones can only be installed after starting the control panel). Addresses of the
keypads must be set within the range from 0 to 3. For how to program addresses of the
keypads, please refer to p. 18.
Mounting the PRF-LCD keypad
The keypad is designed for indoor installation. The place of installation should be readily
accessible to the system users.
1. Open the keypad enclosure (Fig. 3).

SATEL PERFECTA-IP 9
Fig. 3. Opening the keypad enclosure.
2. Put the enclosure base on the wall and mark the location of mounting holes.
3. Drill the holes in the wall for wall plugs (screw anchors).
4. Run wires through the opening in the enclosure base.
5. Using wall plugs (screw anchors) and screws, fasten the enclosure base to the wall. The
wall plugs and screws must be selected so as to suit the mounting surface (must be
different for concrete and brick, different for plaster or wood, etc.).
6. Connect the keypad terminals to the corresponding terminals of the control panel (see:
Fig. 4).
7. Put the cover on the catches and snap the enclosure shut.
8. Lock the cover using screws.

10 PERFECTA-IP SATEL
Fig. 4. Connecting keypad to the control panel.
6.5.2 Connecting 433 MHz keyfobs receiver expansion module
PERFECTA-IP 32
You can connect the INT-RX-S expansion module to the PERFECTA-IP 32 control panel.
The module enables 433 MHz keyfobs to be assigned to the users (up to 15 keyfobs).
Address 7 (07h) must be set in the module.
Fig. 5. Connecting the INT-RX-S expansion module to the control panel.
Fig. 6. Setting DIP-switches in the INT-RX-S expansion module.
6.5.3 Connecting the hardwired zone expanders
You can connect 3 INT-E zone expanders to the control panel. Each expander allows adding
8 programmable wired zones to the system.

SATEL PERFECTA-IP 11
Fig. 7. Connecting the INT-E expander to the control panel.
Address 12 (0Ch), 13 (0Dh) or 14 (0Eh) must be set in the zone expander.
The DIP-switch 10 must be set to the OFF position.
Fig. 8. Setting the DIP-switches in the INT-E expander.
Table 2 shows numbering of the expander zones depending on the address set. If a number
of expander zone coincides with a number of wireless zone, the expander zone will not be
supported.
Expander address
Zone numbers
decimally
hexadecimally
12
0C
9-16
13
0D
17-24
14
0E
25-32
Table 2.
The expander can be identified as INT-E (no dedicated power supply is connected to
the expander) or INT-EPS (dedicated power supply is connected to the expander).

12 PERFECTA-IP SATEL
6.5.4 Connecting the hardwired output expander
You can connect the INT-O or INT-ORS expander to the control panel. This enables
expansion of the system by adding 8 programmable wired outputs.
Address 15 (0Fh) must be set in the expander. In the case of the INT-ORS expander, the
DIP-switch 10 must be set to the ON position.
The expander can be identified as INT-O (no dedicated power supply is connected to
the expander) or INT-OPS (dedicated power supply is connected to the expander).
Fig. 9. Connecting the INT-O expander to the control panel.
Fig. 10. Setting DIP-switches in the INT-O expander.
Fig. 11. Setting DIP-switches in the INT-ORS expander.
6.6 Connecting detectors and other devices to the zones
Zones of the control panel support the following wiring configurations:
NC – wiring configuration that allows connecting a detector with NC (normally closed) alarm
output. Opening the circuit will trigger an alarm.
NO – wiring configuration that allows connecting a detector with NO (normally open) alarm
output. Closing the circuit will trigger an alarm.
EOL – wiring configuration that allows connecting a detector with NC or NO alarm output. An
EOL resistor must be used in the circuit. Alarm will be triggered by closing or opening
the circuit.

SATEL PERFECTA-IP 13
2EOL/NC – wiring configuration that is recommended when connecting a detector with NC
alarm output and tamper output. Two EOL resistors must be used in the circuit. The
zone can distinguish between 3 states: normal, alarm and tamper.
2EOL/NO – wiring configuration similar as 2EOL/NC, but for detectors with the NO alarm
output.
Shutter – wiring configuration that allows connecting a roller shutter detector.
Vibration – wiring configuration that allows connecting a vibration detector. You can also
connect to the zone a detector with NC alarm output (e.g. vibration detector and
magnetic contact can be connected in series).
Fig. 12. The ways to connect detectors to zones. The detector outputs are designated with
letters: A – alarm, T – tamper.

14 PERFECTA-IP SATEL
PERFECTA-IP
Fig. 13. Example of connecting an NC detector (NO detector connect in the same way).
PERFECTA-IP
Fig. 14. Example of connecting an NC detector in Single EOL configuration.

SATEL PERFECTA-IP 15
PERFECTA-IP
Fig. 15. Example of connecting an NO detector in Single EOL configuration.
PERFECTA-IP
Fig. 16. Example of connecting an NC detector in Double EOL (2EOL) configuration (NO
detector connect in the same way).
End-of-line resistors
For the Single EOL configuration, use a 2.2 kΩresistor to close the circuit. For the Double
EOL (2EOL) configuration, use two 1.1 kΩresistors.
6.7 Connecting the sirens
It is recommended that the control panel be started without connected sirens. This will
prevent accidental triggering of the alarm after the control panel is started.

16 PERFECTA-IP SATEL
Depending on the siren type:
•sirens without own power supply (e.g. SP-500, SP-4001, SP-4003, SPL-2010, SPW-100,
SPW-210, SPW-220) – high-current outputs are to be used to trigger the signaling,
•sirens with own power supply (e.g. SP-4002, SP-4004, SP-4006, SP-6500, SPLZ-1011,
SD-3001, SD-6000) – it is recommended to use low-current outputs to trigger the
signaling, and high-current ones – to supply power.
Fig. 17. Connecting sirens to the control panel outputs. I – siren without own power supply.
II - siren with own power supply.
6.8 Connecting the Ethernet network
The device is designed to be used only in the local area networks (LAN). It must
not be connected directly to the public computer network (MAN, WAN). For
establishing connection with public networks, use a router or xDSL modem.
To connect the control panel to the Ethernet network, use a 100Base-TX standard compliant
cable (identical to that used for connecting computers to the network). The cable must be
terminated with a RJ-45 plug.
6.9 Connecting the power supply and starting the control panel
Do not connect power until all installation operations are completed.
6.9.1 Main power supply
The control panel requires 18 VAC (±10%) power supply. It is recommended that
a transformer with 40 VA rating be used.
The transformer should be permanently connected to the 230 VAC mains supply. Before you
make the cabling, familiarize yourself with the electrical installation of the facility. Make sure
that the circuit you choose for powering the control panel will be always alive. The circuit
must be provided with a 2-pole switch disconnector with at least 3 mm contact separation
and/or short-circuit protection with a 16 A time-delay fuse. The owner or user of the alarm
system should be instructed on how to disconnect the transformer from the mains (e.g. by
indicating the fuse which protects the control panel supply circuit).

SATEL PERFECTA-IP 17
Do not connect two devices with power supply to one-section transformer.
Before connecting transformer to a circuit from which it will be powered, make
sure the circuit is de-energized.
6.9.2 Backup power supply
A 12 V lead-acid sealed battery should be connected to the control panel as a backup power
source. The battery capacity must be adequately selected to match current consumption in
the system. According to EN 50131 Grade 2, the battery must ensure operation of the system
without mains supply for 12 hours.
If the battery voltage drops below 11 V for longer than 12 minutes (3 battery tests), the
control panel will indicate battery failure. When the voltage goes down to approx. 10.5 V, the
battery will be disconnected.
Do not connect deeply discharged battery to the control panel (with voltage
across unloaded terminals below 11 V). The battery should be precharged with
a proper charger.
The used batteries must not be discarded, but should be disposed of in
accordance with the existing rules for environment protection.
6.9.3 Control panel power-up / start-up procedure
1. De-energize the 230 VAC circuit to which the transformer is to be connected.
2. Connect the 230 VAC wires to the terminals of transformer primary winding.
3. Connect the terminals of transformer secondary winding to the control panel AC
terminals. To make the connection, use flexible conductors with a cross-section of 0.5 –
0.75 mm2, or rigid conductors with a cross-section of 1 – 2.5 mm2.
4. Connect the battery to the dedicated leads (positive terminal to RED lead, negative
terminal to BLACK lead). If the battery has screw-type cable lugs, use adapters delivered
with the control panel (do not cut off the battery cable lugs). The control panel will not
start after connecting the battery alone.
5. Turn on 230 VAC power supply in the circuit to which the transformer is connected.
The control panel will start operating.
The above mentioned power-up sequence (first the battery, then the 230 VAC mains)
will ensure proper operation of the power supply unit and the electronic protection
circuits, thus preventing damage to the alarm system components caused by
installation mistakes, if any.
If it is necessary to de-energize the control panel, turn off the main power supply (AC)
first, and the backup power supply (battery) afterwards. Observe the above described
procedure when reconnecting the power supply.
6.9.4 Starting the service mode
If, after starting the alarm control panel, you want to perform any operations that not require
power-off (e.g. to adjust sensitivity in wired detectors), enter the service mode.
When the control panel is running in service mode, tamper alarms are not
generated.
1. Enter the service code (by default: 12345) and press .
2. User menu appears.
3. Press .

18 PERFECTA-IP SATEL
4. When the cursor shows the SERVICE MODE function, press .
5. Service mode menu will be displayed (the cursor will show the END SM function).
6.9.5 Emergency procedure of the control panel start-up
If the control panel fails to start properly, keypads are not supported, codes are not accepted
by the control panel etc., despite all connections having been made correctly, follow the steps
below:
1. Turn off the control panel power supply (first disconnect the AC power, and then the
battery).
2. Put a jumper on the RESET pins.
3. Turn on the control panel power supply (first connect the battery and then the AC power).
4. Wait a few seconds (until LEDs next to the RESET pins stop blinking) and remove the
jumper from the RESET pins. The control panel will enter the service mode. The service
mode menu will be displayed on the wired keypad with the lowest address.
If there is no wired keypad in the alarm system or there is no communication with the
wired keypads (e.g. when the communication bus is shorted), you can get access to
the service mode menu from the wireless keypad with the lowest address. Press any
key on this keypad within 30 seconds of removing jumper from the RESET pins.
The service mode menu will not be displayed, if the DISABLE SERVICE MODE option is
enabled in the control panel. The “Factory settings ? 1=Yes” message will be
displayed on the keypad with the lowest address. You can press to restore the
factory default settings. The service mode menu will not be displayed until the factory
settings are restored.
6.9.6 First steps after starting-up the control panel
Control panel with wired keypads
If wired keypads are connected to the control panel, then, after starting the control panel with
factory settings:
1. Set correct, individual addresses in the wired keypads.
2. Run the function of identification of devices connected to the communication bus of the
control panel.
Control panel without wired keypads PERFECTA-IP 32-WRL
If no wired keypads are connected to the control panel, then, after starting the control panel
with factory settings:
1. Connect computer to alarm control panel.
2. Use the PERFECTA SOFT program to add wireless keypads.
3. Run the function of identification of devices connected to the communication bus of the
control panel.
6.10 Programming addresses for the hardwired keypads
An individual address from the 0 to 3 range must be set for each keypad. By default, address
0 is preset for all wired keypads. After starting the alarm control panel with factory default
settings, all keypads connected to the bus are supported, no matter what their addresses are.
This allows you to program individual address for the keypads.
Remember to program an individual address if a new keypad is connected to the
already functioning alarm system.