Satel PERFECTA-IP User manual

USER
MANUAL
perfecta-ip_u_en 07/20
SATEL sp. z o.o.
ul. Budowlanych 66 • 80-298 Gdańsk • POLAND
tel. [phone]
www.satel.eu
Alarm Control Panel PERFECTA-IP
Firmware Version 1.04

IMPORTANT
Before you start using the control panel, please read carefully this manual in order to avoid
mistakes that can lead to malfunction or even damage to the equipment.
Changes, modifications or repairs not authorized by the manufacturer shall void your rights
under the warranty.
To ensure adequate protection, the alarm security system must be in good working order,
therefore SATEL recommends that it be regularly tested.
The alarm system can not prevent burglary, hold-up or fire from happening, but in emergency
situation it will allow you to take steps to minimize the potential damage (by triggering optical
or acoustic alarm signal, notifying appropriate authorities of the alarm etc.). Thus, it can deter
any would-be intruders.
SATEL aims to continually improve the quality of its products, which may result in changes in
their technical specifications and software. Current information about the changes being
introduced is available on our website.
Please visit us at:
http://www.satel.eu
Hereby, SATEL sp. z o.o. declares that the radio equipment type PERFECTA-IP 32 /
PERFECTA-IP 32-WRL is in compliance with Directive 2014/53/EU. The full text of the
EU declaration of conformity is available at the following internet address:
www.satel.eu/ce
Factory default codes:
Service code: 12345
User 15 code: 1111
The following symbols may be used in this manual:
- note,
- caution.

CONTENTS
1. Introduction .....................................................................................................................3
2. Technical reliability of the alarm system.......................................................................3
3. Glossary...........................................................................................................................3
4. EN 50131 standard for Grade 2 consequences ............................................................5
5. Keypads ...........................................................................................................................6
5.1 Keypads description ..............................................................................................................6
5.1.1 LEDs presenting partition and system state.............................................................................6
5.1.2 Display......................................................................................................................................7
5.1.3 Keys..........................................................................................................................................8
5.1.4 Sound signaling ........................................................................................................................8
5.2 Codes ....................................................................................................................................9
5.2.1 Factory default codes..............................................................................................................10
5.3 Arming .................................................................................................................................10
5.3.1 Arming without partition selection...........................................................................................10
5.3.2 Arming the selected partition..................................................................................................10
5.3.3 Quick arming...........................................................................................................................10
5.3.4 Arming without delay...............................................................................................................11
5.3.5 Terminating the exit delay countdown....................................................................................11
5.3.6 Service mode and arming.......................................................................................................11
5.3.7 System problems and arming failure......................................................................................11
5.4 Disarming and alarm clearing..............................................................................................12
5.4.1 Disarming and alarm clearing without partition selection.......................................................12
5.4.2 Alarm clearing without disarming............................................................................................12
5.4.3 Disarming and alarm clearing in selected partition.................................................................12
5.5 Triggering the alarm from keypad........................................................................................12
5.6 Turning the CHIME on /off...................................................................................................13
5.7 User menu...........................................................................................................................13
5.7.1 Navigating through the menu and running functions..............................................................13
5.7.2 Data editing.............................................................................................................................13
5.7.3 User functions list....................................................................................................................14
5.8 Changing code.....................................................................................................................16
5.9 Users ...................................................................................................................................16
5.9.1 Adding a user..........................................................................................................................16
5.9.2 Editing a user..........................................................................................................................17
5.9.3 Removing a user.....................................................................................................................18
5.9.4 Adding keyfob.........................................................................................................................18
5.9.5 Configuring keyfob settings ....................................................................................................18
5.9.6 Removing keyfob....................................................................................................................18
5.10 Outputs reset.......................................................................................................................18
5.11 Zone bypassing ...................................................................................................................19
5.11.1 Zone inhibiting.........................................................................................................................19
5.11.2 Zone isolating..........................................................................................................................19
5.12 Viewing the event log...........................................................................................................20
5.13 Setting the clock ..................................................................................................................20
5.14 Checking the troubles / system state...................................................................................20
5.14.1 Information on system state....................................................................................................20
5.14.2 What to do in the event of trouble...........................................................................................20
5.14.3 Trouble memory and clearing the trouble memory.................................................................21
5.15Output control......................................................................................................................21
5.15.1 Quick control of outputs..........................................................................................................21
5.15.2 Controlling the outputs by means of function .........................................................................21
5.16 Tests....................................................................................................................................21
5.16.1 Zone test.................................................................................................................................21

2 PERFECTA-IP SATEL
5.16.2 Output test.............................................................................................................................. 22
5.16.3 Checking the level of radio signal.......................................................................................... 22
5.16.4 Starting the test transmission................................................................................................. 22
5.16.5 ID change............................................................................................................................... 22
5.16.6 Checking the MAC address / ID number / network address.................................................. 23
5.16.7 Checking the firmware version of devices in system............................................................. 23
5.16.8 Starting remote update of the control panel firmware............................................................ 23
5.17 Replacing battery in wireless keypad.................................................................................. 23
5.18 Service access.................................................................................................................... 24
5.19 Establishing communication with PERFECTA SOFT via Ethernet....................................... 24
5.20 Service mode ......................................................................................................................24
6. Keyfobs ..........................................................................................................................24
7. PERFECTA CONTROL application..................................................................................25
8. Sirens..............................................................................................................................27

SATEL PERFECTA-IP 3
1. Introduction
Thank you for choosing the product offered by the SATEL Company. Wishing you full
satisfaction with the choice you made, we are always ready to provide you with professional
assistance and information on our products.
The SATEL Company is manufacturer of a broad range of devices dedicated for use in
security alarm systems. Further information is available on our website www.satel.eu or at
the points of sale offering our products.
It is recommended that the installers prepare their own user manual for the alarm
system installed by them. The manual must include all changes and modifications in
relation to the factory default settings.
The installer should train the users in the rules of operating the alarm system.
2. Technical reliability of the alarm system
A failure of any component of the alarm system will result in deterioration of the level of
protection. Unfortunately, the devices which are installed outside (e.g. the outdoor sirens) are
exposed to the adverse effects of weather. During storms, the devices connected to the
electrical system are vulnerable to damage as a result of atmospheric discharge.
The control panel is provided with a number of safeguards and automatic diagnostic features
to test the system performance. Detection of irregularities is signaled by the LED on the
keypad. You should immediately respond to such a signal, and, if necessary, consult
the installer.
In addition, some features designed for testing the alarm system are available in the control
panel. They make it possible to check the detectors, sirens, etc for correct functioning. Only
regular testing and inspection of the alarm system will allow you to keep a high level
of protection against intrusion.
It is recommended that the installer, at the request of the user, carry out periodic
maintenance of the alarm system.
It is in the interest of the user to anticipate and plan in advance the procedures in case an
alarm is set off by the control panel. It is important to be able to verify the alarm, determine its
source and take appropriate actions (e.g. evacuation in the event of a fire alarm).
3. Glossary
Alarm – reaction of the alarm system to detection by the detectors of an intruder in the
protected area, or to another event within the protected area (e.g. glass pane break, gas
detection, etc.). The alarm can be signaled in keypads or by sirens (during a defined time
or until cleared). Additionally, information on the alarm can be sent to the monitoring
station or the user.
Alarm zone – the zone whose violation can result in the alarm being triggered. The alarm
zones can be either instant (violation will trigger the alarm at once) or delayed (violation
will only trigger the alarm after a defined period of time has elapsed, e.g. the entry delay).
Armed mode – the status of alarm system in which zone violation will trigger the alarm.
Code – a sequence of digits that allows the user to operate the alarm system by using
keypad.

4 PERFECTA-IP SATEL
Day armed mode – the status in which only some zones in the partition are armed, as
selected by the installer. The installer should indicate the zones to be armed when a user
stays in the protected area, but there is no risk of the zones being violated by the user
during the daytime. If no such zones are indicated by the installer, the user will not be able
to arm the partition in this mode.
Detector – the basic component of alarm system, which analyzes the environment and, if
a situation recognized as a threat occurs, transmits appropriate information to the control
panel (e.g. motion detectors on registering motion, magnetic contacts on opening the
door/window, glass-break detectors on breaking glass pane, gas detectors on sensing
gas, etc.).
Entry delay – time counted from the moment of entry into the protected area, which makes it
possible to disarm the partition before the alarm is triggered.
Entry route – the route which the user must have to follow after entry into the protected area
before being able to disarm the system. It is usually the same as the exit route.
Exit delay – time counted from the moment of starting the arming procedure in the partition,
which makes it possible to leave the protected area before the alarm is triggered.
Exit route – the route which the user must have to take after arming before he leaves the
protected area. It is usually the same as the entry route.
Fire alarm – alarm triggered by fire detectors, or from the keypad, in the event of fire.
Full armed mode – the status in which all zones belonging to the partition are armed.
Installer – the person who has installed and configured the alarm system.
Medical (auxiliary) alarm – alarm triggered by means of a button, or from the keypad, if it is
necessary to call the medical assistance.
Night armed mode – the status in which only some zones in the partition are armed, as
selected by the installer. The installer should indicate the zones to be armed when a user
stays in the protected area, but there is no risk of the zones being violated by the user at
night. If no such zones are indicated by the installer, the user will not be able to arm the
partition in this mode.
Panic alarm – alarm triggered by means of the panic button, or from the keypad, in case of
a hold-up.
Partition – a part of the protected area, composed of a number of zones. The division into
partitions makes it possible to limit the access to part of the premises to some selected
users, and to arm/disarm the system only in part of the protected area.
Protected area – the area supervised by detectors being part of the alarm system.
Reporting – reporting events that occurred in the alarm system to the monitoring station. The
information about occurrence of an event can be transmitted via Ethernet. The companies
offering the alarm system monitoring service undertake to intervene if specific events
occur (e.g. alarms, troubles, etc.).
Service code – a code that allows access to the service mode, as well as some functions in
the user menu.
Service technician – the person whose function is to control operability of the installed alarm
system and its components, as well as to eliminate possible problems. These duties can
be fulfilled by the installer or a person assigned by him.
Siren/beacon – a device providing information about alarms or other events in the alarm
system by means of acoustic or optical signaling.

SATEL PERFECTA-IP 5
Tamper alarm – reaction of the alarm system to opening the housing of a device which is
part of the alarm system, tearing off the device from the wall, cutting through the alarm
system cables, etc. Actions taken by the alarm system may be similar as in the event of
alarm, however, if the tamper alarm occurs, it is advisable to call in the installer so that he
can make a checkup.
User – a person which can operate the alarm system, using a code or remote control keyfob.
Warning alarm – in some situations, when the alarm criteria are met, the alarm system does
not take up immediately all the actions provided for in the event of alarm. These actions
are postponed, reaction of the system being limited to signaling warning alarm in keypads
or on indoor sirens/beacons. Thus, the user who has made a mistake entering the
protected area (without disarming the system first), has some extra time to disarm the
system. Contact your installer to obtain detailed information on the situations when the
alarm will be preceded by warning alarm.
Zone – 1. a separated portion of the protected area that can supervised by a detector. 2. the
terminals on control panel/expander electronics board to which you can connect a detector
or another device whose state is to be supervised (panic button, siren tamper contact,
power supply output indicating loss of 230 VAC supply, etc.).
Zone bypassing (inhibiting / isolating) – procedure preventing the alarm from being
triggered by the selected zone when it is in the armed mode. Violations of the zone will be
ignored by the control panel.
Zone violation – a change of the zone status to another, different from that defined for the
normal state (e.g. as a result of motion being sensed by the motion detector, gas being
sensed by the gas detector, etc.).
4. EN 50131 standard for Grade 2 consequences
If the installer has configured the control panel in compliance with the EN 50131 standard
requirements for Grade 2:
1. The user codes should be composed of at least 5 characters.
2. The amount of information provided in the keypads by means of LEDs, display and sound
signaling is limited.
3. The quick arming from keypad (without entering the code) is not available.
4. Arming may be impossible, if one of the situations provided for in the standard occurs
(zone violation, trouble).
How requirements of the standard affect the use of the control panel is described in detail
hereunder.

6 PERFECTA-IP SATEL
5. Keypads
Fig. 1. PRF-LCD / PRF-LCD-WRL keypad.
You can operate the alarm control panel by using a wired keypad (PRF-LCD) or a wireless
keypad (PRF-LCD-WRL – which is supported by the PERFECTA-IP 32-WRL control panel).
Response of the wired keypad to the user's actions is faster than that of the wireless one. If
the wireless keypad is not in use for 20 seconds, it enters inactive mode. In the inactive
mode, the display is off, while the backlighting, LED signaling and audible signaling are
disabled.
The alarm system should include at least one keypad.
5.1 Keypads description
5.1.1 LEDs presenting partition and system state
LED
Color
Description
green
indicates the partition state (each partition has its own LED)
ON – partition is armed
flashing – exit delay countdown is running in partition
red
indicates alarm or alarm memory in the partition (each partition has its
own LED)
The way of presenting the information is shown graphically below.
The information is presented for 2 seconds and repeated ( – LED is
OFF; – LED is ON). The higher position in the list means the higher
priority of the presented status:
– fire alarm,
–burglary / panic alarm,
– warning alarm,
– tamper alarm,
– fire alarm memory,

SATEL PERFECTA-IP 7
–
burglary / panic alarm memory
,
– warning alarm memory,
– tamper alarm memory.
yellow
flashing when the system requires user's attention (e.g. because of
a trouble or trouble memory)
The LED goes off, if one or both partitions are armed.
blue
indicates the service mode
ON – the service menu is available on the keypad
flashing – the service menu is not available on the keypad (it is either
available on another keypad or has been hidden by the installer)
Information about the armed state can be extinguished after a time period defined by
the installer. Entering the code and pressing the key will display again the armed
state information.
If the GRADE 2 global option is enabled by installer:
−the LEDs indicate alarms only after entering the code and pressing ,
−flashing of the LED means that there is a trouble in the system, some zones
are bypassed, or that there was an alarm.
5.1.2 Display
The display provides a number of data, facilitating communication between the alarm system
and the user. The installer defines how the display will be backlit and selects the information
to be shown on the display screen.
The display can work in normal mode or in zone presentation mode (the modes being
toggled by means of the key). When in the normal mode, the date and time (in installer
defined format) or the keypad name are presented in the upper line of the display. In the
zone presentation mode, symbols are displayed, showing the status of zones (where the
control panel settings do not provide for detector presence at a zone, the status of the zone is
not displayed). The numbers around the display correspond to the zone numbers. The
symbols illustrate the following zone states (the higher position on the list, the higher priority
of the presented state):
– inhibited (not displayed when armed),
– isolated (not displayed when armed),
– first triggered alarm,
– fire alarm,
– alarm,
– tamper alarm,
– tamper (Double EOL zone),
– violated,
– fire alarm memory,
– alarm memory,
– tamper alarm memory,
– normal state.
Find out from the installer whether or not the zone status presentation mode is
available.

8 PERFECTA-IP SATEL
The keypad displays the following messages (the higher position on the list, the higher the
priority):
•alarm,
•countdown of entry delay,
•countdown of exit delay,
•alarm memory.
Messages about alarm and alarm memory will not be displayed, if the GRADE 2option
is enabled by the installer.
5.1.3 Keys
The keys bearing digits and letters enable entering the code, as well as data when the
keypad is being used.
Other functions of these keys and the basic function of the other keys are described below.
allows to trigger the medical (aux) alarm (press and hold down for 3 seconds)
allows to turn on/off the CHIME signal in the keypad (press and hold down for
3 seconds)
allows to toggle the LCD keypad display between the normal mode and the zone
state presentation mode (press and hold down for 3 seconds)
allows to:
−arm in the full mode [if the system is disarmed and there is no alarm] or disarm
the system and clear the alarm [if the system is armed and/or there is an alarm]
(enter the code and press )
−trigger the panic alarm (press and hold down for 3 seconds)
allows to:
−open the user menu (enter the code and press )
−trigger the fire alarm (press and hold down for 3 seconds)
allows to arm in the full mode (see “Arming”)
allows to arm in the night mode (see “Arming”)
allows to arm in the day mode (see “Arming”)
allows to disarm the system and clear the alarm (see “Disarming and alarm
clearing”)
5.1.4 Sound signaling
The installer can disable the sound signaling.
Beeps generated when operating
1 short beep – pressing any number key.
3 short beeps – confirmation of:
– starting the arming procedure (there is exit delay in the partition) or arming (there is no
exit delay in the partition),
– disarming and/or alarm clearing,

SATEL PERFECTA-IP 9
– selecting the partition which is to be armed or disarmed, or where alarm is to be cleared
– in such a case the keypad is waiting for the code to be entered,
– turning output off,
– turning off the CHIME in the keypad, using the key,
– switching over the display from the normal mode to the zone status presentation mode,
and vice versa, by means of the key.
4 short beeps and 1 long beep – confirmation of:
– turning output on,
– turning on the CHIME in the keypad, using the key.
2 long beeps – incorrect code or pressing the key, if not preceded by entering code or
selecting a partition.
3 long beeps – refusal to carry out a command (the user does not have the required
authority level or the function is not available).
Beeps generated during programming
1 short beep – pressing any number key.
2 short beeps – entering the user menu, submenu or starting a function.
3 short beeps – exiting the service function on pressing the key.
4 short beeps and 1 long beep – termination of the user function on pressing the key,
or quitting the service mode.
2 long beeps – exiting the function on pressing the key, or an unavailable function.
Event signaling
Only installer selected events are signaled.
Duration of the alarm signaling is to be defined by the installer.
If the GRADE 2 option is enabled by installer, the keypad will not signal by sounds any
troubles and alarms.
5 short beeps – zone violation (CHIME).
Long beep every 3 seconds, followed by a series of short beeps for 10 seconds
and 1 long beep – countdown of exit delay (if the time is shorter than 10 seconds, only
the final sequence of short beeps will be generated).
2 short beeps every seconds – countdown of entry delay.
2 short beeps every 3 seconds – trouble / trouble memory. The installer defines whether
the signaling is to last until trouble restore, or until trouble review / trouble memory
clearing. When one or both partitions are armed, trouble / trouble memory is not audibly
indicated by the keypad.
Short beep every 0.5 seconds – warning alarm.
Continuous beep – alarm.
Long beep every second – fire alarm.
5.2 Codes
Operating the alarm system by means of the keypad is possible after entering the code. Only
some functions can be run without the code being entered.
Do not make your code available to other people.

10 PERFECTA-IP SATEL
Using an incorrect code three times may block the keypad for 90 seconds. As long as
the keypad is blocked, entering the correct code is treated as entering an incorrect
code (“Wrong code” message is displayed).
5.2.1 Factory default codes
By default, the following codes are preprogrammed in the control panel:
user 15 code: 1111
service code: 12345
The factory default codes should be changed before you start using your alarm
system (see: “Changing code”).
5.3 Arming
Completion of the steps below will start the arming procedure. The procedure ends when the
exit delay time elapses (if the procedure is completed successfully, the system becomes
armed – see also “Failure of arming procedure”). If the exit delay time is 0, the system
becomes armed instantly.
The day/night arming modes are available if the installer has defined which zones are
to be active in this armed mode.
During the exit delay countdown, you can leave the partition through the exit route
without triggering alarm.
5.3.1 Arming without partition selection
Enter the code, and then press:
- to arm in full mode,
- to arm in day mode,
- to arm in night mode.
In the partitions you have access to, the arming procedure will begin.
5.3.2 Arming the selected partition
1. Select the partition which is to be armed (press one of the keys: - partition 1; -
partition 2).
2. Select the arming mode (press one of the keys: - full arming; - day arming;
- night arming). Backlight of the keys will start flashing, which indicates that the code
must be entered.
3. Enter the code.
4. Press or press again the key corresponding to the selected arming mode.
5. In the selected partition, the arming procedure will begin.
When the quick arming is available, the steps 3 and 4 are skipped.
5.3.3 Quick arming
The installer may permit arming without entering the code.
1. Indicate the partition(s) to be armed (press one of the keys: - partition 1; -
partition 2; or - both partitions).
2. Select the arming mode (press one of the keys: - full arming; - day arming;
- night arming).
3. In the partition(s), the arming procedure will begin.

SATEL PERFECTA-IP 11
5.3.4 Arming without delay
If there is nobody in the partition or nobody is leaving the partition which is to be set to the
day / night armed mode, you can arm the partition without exit delay (there will be no beeps
accompanying the exit delay countdown). When setting the partition to one of the above-
mentioned armed modes, hold down the armed mode selection key ( , or ) for
about 3 seconds. The exit delay countdown will not run.
5.3.5 Terminating the exit delay countdown
When the exit delay countdown is running, you can terminate it, thus shortening the exit
delay time. Press and hold down , or for about 3 seconds (it is of no
consequence which key you will press).
5.3.6 Service mode and arming
If you try to arm the system when the service mode is active, you will be informed about it by
a message displayed on the keypad. Press if you want to arm the system.
5.3.7 System problems and arming failure
The alarm system can be configured so that the control panel will perform a check during
arming for any problems preventing the system from being armed. The possible problems
that prevent arming are given below:
•at least one zone that must not be violated during arming (the PRIORITY option has been
enabled for the zone by the installer) is violated in the partition,
•at least one alarm zone is violated beyond the exit route in the partition,
•a zone is bypassed in the partition,
•there is tamper in the partition,
•there is trouble in the system.
The check can be performed twice:
•before starting the arming procedure,
•after the exit delay countdown expires.
System not ready and forced arming
If you are trying to arm a partition, but the arming procedure fails to start and the “System not
ready” message is displayed instead, there are some problems in the system that prevent it
from being armed.
When the “System not ready 1=Arm 2=Check”message is displayed, you can:
•press to cancel the arming,
•press to force the arming,
•press to check what has prevented the arming procedure from starting.
When the “System not ready 2= Check”message is displayed, you can:
•press to cancel the arming,
•press to check what has prevented the arming procedure from starting.
If forced arming is not available, you will be able to arm the system only after the
causes that made starting of the arming procedure impossible are eliminated.
List of problems
If, after pressing , it turns out there are several causes that prevent arming, you can
scroll the list using the or keys.

12 PERFECTA-IP SATEL
If you want to bypass a violated zone or unbypass a bypassed zone, press (you need
to have the ZONE INHIBITION right). A prompt will appear asking you whether to execute the
function. Press to confirm or to deny.
Having reviewed the list of problems, press to go back to the “System not ready”
message.
Failure of arming procedure
If, after the exit delay countdown expires, the system fails to arm, there are some problems
that did not exist before the exit delay countdown was started. Such restriction may be
imposed by standards, e.g. EN 50131 for Grade 2.
5.4 Disarming and alarm clearing
If the partition is armed and an alarm is triggered in it, disarming will be accompanied by the
alarm clearing.
Alarm clearing results in canceling the voice messaging about alarm (unless the
control panel has already managed to notify the users about the alarm).
5.4.1 Disarming and alarm clearing without partition selection
Enter the code and then press . Disarming / alarm clearing will take place in the
partitions to which you have access.
5.4.2 Alarm clearing without disarming
If the partition is armed and you want to clear the alarm without disarming the partition, enter
the code and then press , or (it is of no consequence which key you will
press). In the partitions you have access to, the alarm will be cleared.
You cannot clear the warning alarm without disarming the system first.
5.4.3 Disarming and alarm clearing in selected partition
1. Select the partition which is to be disarmed and/or where alarm is to be cleared (press
one of the keys: - partition 1; - partition 2).
2. Press . Backlight of the keys will start flashing, which indicates that the code must be
entered.
3. Enter the code.
4. Press or .
5. Selected partition will be disarmed / alarm will be cleared.
5.5 Triggering the alarm from keypad
The installer can permit triggering alarms from the keypad. To trigger an alarm, do the
following:
fire alarm – press and hold down for about 3 seconds,
medical (auxiliary) alarm – press and hold down for about 3 seconds,
panic alarm – press and hold down for about 3 seconds. The installer defines whether
the loud panic alarm (indicated by the keypads) or the silent panic alarm (not indicated by
the keypads) will be triggered.

SATEL PERFECTA-IP 13
5.6 Turning the CHIME on /off
The CHIME is five short sounds by means of which the keypad will inform you e.g. that
a door / window is open. The installer defines which zones of the alarm system can trigger
the CHIME and whether it can be turned on/off by the users.
Press and hold down for about 3 seconds to turn on or off the CHIME signaling.
5.7 User menu
Enter the code and press to get access to the user menu. The functions you can run
will be displayed. The list of available functions depends on your rights, as well as on the
state and configuration of the system.
In order to quit the function and/or user menu, press . The keypad will quit the menu
automatically, if 2 minutes have elapsed since the last keypress.
5.7.1 Navigating through the menu and running functions
To navigate throughout the menu, you can use the arrow keys or number shortcuts. You can
also combine the two methods. The cursor shows the submenu you can enter / function
you can run.
Using the arrow keys
1. Using the and keys, find the required submenu or function.
2. Press or to open a submenu (use the key to go back to the main menu)
or run a function.
Using the number shortcuts
Most submenus and functions are designated by numbers. To find these numbers, refer to
section “User functions list”. Using the number keys, enter the number of submenu / function
to enter the submenu / run the function. You can enter at once a sequence of several digits
(corresponding to successive numbers of submenus and functions) to quickly run the
selected function.
For example, to start the zone inhibiting function, enter the user menu and then press
, where:
- entering the 4.ZONE BYPASSES submenu,
- running the 1.INHIBIT function.
Remember that the sequence of digits which starts a function e.g. from the main menu
level will not start the same function from the submenu level.
5.7.2 Data editing
The editing method depends on the type of data. Having completed the editing, press
to save the changes. If you want to exit the function without saving the changes, press .
Selection from the single-choice list
In the lower line of the display, the currently selected item is presented. You can scroll the list
using the and keys.
Selection from the multiple-choice list
In the lower line of the display, one of the items you can choose from is presented. You can
scroll the list using the and keys. The following symbol is situated in the upper
right corner of the display:
– displayed item is selected / option is enabled,

14 PERFECTA-IP SATEL
– displayed item is not selected / option is disabled.
Press any number key to change the currently shown symbol for another one.
If you want to see the status of all items (these can be e.g. zones, outputs, options, etc.),
press or . The numbers around the display allow the items to be identified. Use the
and keys to move the cursor. After hovering the cursor over the selected item,
you can change its status by pressing any number key. If you want to restore the previous
way of presentation of the list, press or .
Entering decimal values
To enter digits, use the number keys. Use the and keys to move the cursor. In
some functions, the key deletes the character on the left side of the cursor.
Entering names
The characters that can be entered by using the keys are presented in Table 1. Keep
pressing the key until the required character appears. Long press the key to display the digit
assigned to it.
Shown on the right side in the upper line of the display is information about the letter case:
[ABC] or [abc] (it will be displayed after pressing any key and will be visible for a few seconds
after the last keystroke).
Use the and keys to move the cursor. The key deletes the character on the
left side of the cursor.
Key
Characters available after next keystroke
!
?
'
`

"
{
}
$
%
&
@
\
^
|
#
1
a
b
c
2
d
e
f
3
g
h
i
4
j
k
l
5
m
n
o
6
p
q
r
s
7
t
u
v
8
w
x
y
z
9
.
,
:
;
+
-
/
=
_
<
>
(
)
[
]
0
Table 1. Characters available when entering names. The upper case letters are available
under the same keys (to change the letter case, press ).
5.7.3 User functions list
Presented below are all items of the user menu. The menu displayed on the keypad contains
only the items to which you have access, because of the rights granted to you or status of the
system.
Shown in square brackets are key sequences that enable calling the given submenu or
starting the given function from the main menu level.
1.Change code changing own code
2.Users
[21] 1.New user adding new user
[211] 1.Code entering code

SATEL PERFECTA-IP 15
[212] 2.Schedule selecting user schedule
[213] 3.Partitions selecting supported partitions
[214] 4.Add key fob adding keyfob
[215] 5.Remov.key fob removing keyfob
Button ○selecting function to run with button ○
Button □selecting function to run with button □
Button ▲selecting function to run with button ▲
Button ■selecting function to run with button ■
Button ●selecting function to run with button ●
Button ○+●selecting function to run with buttons ○+●
Key fob event do you want to write keyfob use to event log
[218] 8.Name entering the user name
[22] 2.Edit user editing a user
[selecting user]
1.Code editing code
2.Schedule changing user schedule
3.Partitions selecting supported partitions
4.Add key fob adding keyfob
5.Remov.key fob removing keyfob
Button ○selecting function to run with button ○
Button □selecting function to run with button □
Button ▲selecting function to run with button ▲
Button ■selecting function to run with button ■
Button ●selecting function to run with button ●
Button ○+●selecting function to run with buttons ○+●
Key fob event do you want to write keyfob use to event log
8.Name editing user name
[23] 3.Remove user removing a user
3.Outputs reset deactivating outputs / activating 21. DETECTORS RESET output
4.Zone bypasses
[41] 1.Inhibit inhibiting zones
[42] 2.Isolate isolating zones
5.Event log viewing events
6.Set time setting the clock
7.Troubles / 7.System state checking troubles / checking system status
8.Outputs ctrl. controlling the outputs
9.Tests
[91] 1.Zones test starting zone test
[92] 2.Outputs test starting output test
[93] 3.Signal level checking radio signal level
[94] 4.Test event starting manual test transmission
[96] 6.ID change changing existing ID

16 PERFECTA-IP SATEL
[97] 7.MAC/ID/ADR checking the MAC address / ID number / network address
[98] 8.FW versions checking firmware version of devices
[90] 0.FW update starting remote update of the control panel firmware
Replace battery enabling battery replacement in wireless keypad
Service access defining service access rules
PERFECTA Soft establishing communication with PERFECTA SOFT via Ethernet
Service mode starting service mode
5.8 Changing code
1. Enter the user menu and press to run 1.CHANGE CODE function.
2. Enter the new code.
3. Press to save new code.
5.9 Users
There can be up to 15 users in the system.
5.9.1 Adding a user
1. Enter the user menu and press in turn to run 1.CODE function.
2. Enter the new user's code.
3. Press to save the code.
4. Functions that allow entering the user data will be displayed.
5. Press to run 2.SCHEDULE function.
6. Select the user schedule. Five installer defined schedules are available. The schedule
defines the rights the user will have and the default way of keyfob operation (you can add
the keyfob later on).

SATEL PERFECTA-IP 17
Schedule name and number
Normal
Simple
Arms only
Duress
Master
Right
1
2
3
4
5
Arming
    
Disarming
   
Alarm clearing
   
DURESS

Zone inhibition
 
Zone isolation

Change access code
   
Users editing
 
Control
  
Tests
 
Service access

Changing panel ID

Table 2. Factory default settings of the user schedules. The installer can change the names
of schedules and assign other rights to them.
Using the DURESS right code will trigger a silent alarm, which is not signaled in any
way, but the alarm code will be sent to the monitoring station.
7. Press to confirm schedule selection.
8. Functions that allow entering the user data will be displayed.
9. Press to run 3.PARTITIONS function.
10.Assign partition(s) to which the user is to have access. The user should have access to at
least one partition.
11.Press to confirm partition selection.
12.Functions that allow entering the user data will be displayed.
13.Press to run 8.NAME function.
14.Enter the user name.
15.Press to save the name.
16.Functions that allow entering the user data will be displayed.
17.Press to finish adding the user.
18.Prompt for saving the changes will be displayed.
19.Press to save changes.
5.9.2 Editing a user
1. Enter the user menu and press in turn to run 2.EDIT USER function.
2. Use the or key to select the user you want to edit.
3. Press to start editing the selected user.

18 PERFECTA-IP SATEL
4. Functions that allow editing the user data will be displayed.
5. Use available functions to modify the user data (proceed in the same way as when adding
a user).
6. Having made all changes, press to finish editing the user.
7. Prompt for saving the changes will be displayed.
8. Press to save changes.
5.9.3 Removing a user
1. Enter the user menu and press in turn to run 3.REMOVE USER function.
2. Use the or key to select the user you want to remove.
3. Press to remove selected user.
5.9.4 Adding keyfob
You can add a keyfob when adding or editing a user.
1. Press to run 4.ADD KEY FOB function.
2. Press twice any button of the keyfob (messages on the display will prompt you for what to
do next).
3. Type and serial number of the keyfob being added will be displayed.
4. Press to add the keyfob.
5.9.5 Configuring keyfob settings
You can configure a keyfob when adding or editing a user.
1. Run BUTTON ○function.
2. Use the or key to select operation that control panel is to perform after the
button ○is pressed on the keyfob.
For information on zone types and output functions, please consult the installer.
3. Press to confirm the selection.
4. Functions that allow entering / editing the user data will be displayed.
5. Configure settings of the other keyfob buttons in the same way.
6. Use the key to find the KEY FOB EVENT option.
7. Use the key to define whether the use of the keyfob is to be saved to the event log
( - yes, - no).
5.9.6 Removing keyfob
You can remove a keyfob when adding or editing a user.
1. Press to run 5.REMOV.KEY FOB function.
2. Type and serial number of the keyfob being removed will be displayed.
3. Press to remove the keyfob.
5.10 Outputs reset
Using 3.OUTPUTS RESET function you can:
•deactivate 1. EXTERNAL SIREN, 2. INTERNAL SIREN, 3. BURGLARY, 4. FIRE ALARM, 5. DURESS
ALARM, 6. PANIC ALARM, 7. AUX. ALARM, 8. ALARM –NOT VERIFIED, 9. ALARM -VERIFIED,
10. TAMPER ALARM, 13. ZONE VIOLATION and 14. CHIME function outputs,