Sauder 414435 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-22
Français pg 23-25
Español pg 26-28
Lot # 361789 04/15/14
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Desk
Pogo Collection | Model 414435
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
WARNING
CHOKING HAZARD - Small Parts
Not for children under 3 years.
Adult assembly required.

Table of Contents Assembly Tools Required
3
4
5-22
23-25
26-28
29-30
31
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
414435 www.sauder.com/servicesPage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A2 RIGHT END (1)
B2 LEFT END (1)
C TOP (1)
D BOTTOM (1)
D74 DRAWER BACK (1)
D83 RIGHT DRAWER SIDE (1)
D84 LEFT DRAWER SIDE (1)
D706 DRAWER BOTTOM (1)
E MODESTY PANEL (1)
F2 FRONT PANEL (1)
G SIDE PANEL (1)
H BACK (1)
I BRACE (1)
J FRONT LEG (1)
K REAR LEG (1)
L BASE (1)
M DRAWER FRONT (1)
R RAIL (1)
S TOP MOLDING (1)
Now you know
our ABCs.
414435www.sauder.com/services Page 3
D83
D84
D74
D706
A2
B2
C
D
E
F2
G
H
I
J
K
LM
R
S

CARD SHEET - 1
40M
Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
414435 www.sauder.com/servicesPage 4
ANGLE BRACKET - 5
5G
GOLD 5/16" FLAT HEAD SCREW - 8
3S
BROWN 7/16" LARGE HEAD SCREW - 16
6S
KNOB - 1
60K
BLACK 1-1/8" PAN HEAD SCREW - 1
9S
CARD HOLDER - 1
21M
SLIDE CAM - 2
10A HIDDEN CAM - 18 1F CAM DOWEL - 10 2F
BLACK 1-7/8" FLAT HEAD SCREW - 2
2S
CAM SCREW - 8
8F
NAIL - 22
1N
WOOD DOWEL - 5
15F
GLUE - 1
54M
BLACK 9/16" FLAT HEAD SCREW - 2
32S
35DA CABINET RIGHT - 1 35DB CABINET LEFT - 1 DRAWER RIGHT - 1 35DC 35DD DRAWER LEFT - 1
SILVER 3/8" MACHINE SCREW - 2
97S
METAL BRACKET - 3
4G
30S BLACK 1-9/16" FLAT HEAD SCREW - 4

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty carton
to avoid scratching your unit or the floor.
å Push eighteen HIDDEN CAMS (1F) into the ENDS (A2 and B2),
BOTTOM (D), MODESTY PANEL (E), and SIDE PANEL (G).
Then, insert the metal end of a CAM DOWEL (2F) into each
HIDDEN CAM, except in the long edges of the SIDE PANEL (G)
and MODESTY PANEL (E).
414435www.sauder.com/services Page 5
A2
B2
D
G
E
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tighten the HIDDEN CAMS in this step.
Do not insert
CAM DOWELS
into these edges.
Arrow
Arrow
1F
Arrow
1F
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
Do not insert
CAM DOWELS
into this part.
(18 used)
(10 used)
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1744
to watch a video on how to assemble your unit.

Step 2
å Fasten the CABINET RIGHT (35DA) and CABINET LEFT (35DB)
to the ENDS (A2 and B2). Use four GOLD 5/16" FLAT HEAD
SCREWS (3S) through holes #1 and #3.
414435 www.sauder.com/servicesPage 6
1
1
2
3
3
2A2
B2
35DA
35DA
35DB
35DB
Roller end
Roller end
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Remember:
Righty tighty.
Lefty loosey.

å Flip the SIDE PANEL (G) over. Turn two BLACK 9/16"
FLAT HEAD SCREWS (32S) into SIDE PANEL (G) until the
shoulders of the SCREWS rest on the surface of it.
å Slide the BRACE (I) onto the SIDE PANEL (G). Line up the
groove in the MOLDING over the heads of the SCREWS
in the SIDE PANEL.
Step 3
414435www.sauder.com/services Page 7
After sliding on the BRACE,
these edges should be even.
G
GI
I
Apply pressure with your hands
as you guide the MOLDINGS over
the SCREWS and onto the ENDS.
Shoulder
BLACK 9/16" FLAT HEAD SCREW
(2 used in this step)
32S
After sliding on the BRACE,
these edges should be even.

Step 4
å Turn eight CAM SCREWS (8F) into the LEGS (J and K).
å Fasten the LEGS (J and K) to the SIDE PANEL (G). Tighten
six HIDDEN CAMS.
414435 www.sauder.com/servicesPage 8
8F
8F
J
J
K
K
G
Surface with
HIDDEN CAMS
1st
2nd
These edges
should be even.
Edge with
BRACE (I)
(8 used)
1
2

å Fill the hole in the top edge of the FRONT LEG (J) 1/4 to 1/2
full with GLUE (54M). Push a WOODEN DOWEL (15F) into
the hole of the FRONT LEG. Wipe away the excess GLUE.
å Fill the hole in the TOP (C) 1/4 to 1/2 full with GLUE (54M).
å Flip the SIDE PANEL upside down and fasten the FRONT
LEG (J) and SIDE PANEL (G) to the TOP (C). Tighten two
HIDDEN CAMS. Wipe away the excess GLUE.
Step 5
414435www.sauder.com/services Page 9
54M
54M
G
J
C
J
15F
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
Surface with
HIDDEN CAMS
G
2nd
1st
Surface
with holes
Rounded edge
Fill the holes 1/4 to 1/2 full with GLUE.
Inspect the parts thoroughly before
assembling. Disassembly of glued
parts is extremely dicult.
Caution
!

Step 6
å Fasten the MODESTY PANEL (E) to the REAR LEG (K).
Tighten two HIDDEN CAMS.
414435 www.sauder.com/servicesPage 10
E
K
Finished Surface
Finished edge
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution