Sauder Cannery Bridge 431315 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
Enlish p 1-40
Français p 41-44
Español p 45-48
Lot # 570167 08/04/21
Purchased: __________________
Small Credenza
Cannery Bride Collection | Model 431315
Congratulations. You
are now an adult.

Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
3
4-5
6
7-40
41-44
45-48
49-50
51
Pae 2 www.sauder.com/service 431315

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A LEFT END (1)
B RIGHT END (1)
C UPRIGHT (1)
D TOP (1)
E BOTTOM (1)
F SKIRT (1)
G SHELF (1)
H BRACE (1)
J LEFT BACK (1)
K RIGHT BACK (1)
L PENCIL DRAWER FRONT (1)
M PENCIL DRAWER BOTTOM (1)
N FILE DRAWER FRONT (2)
O FILE LEFT DRAWER SIDE (2)
P FILE RIGHT DRAWER SIDE (2)
Q FILE DRAWER BACK (2)
R FILE DRAWER BOTTOM (2)
S DOOR (1)
T PENCIL LEFT DRAWER SIDE (1)
U PENCIL RIGHT DRAWER SIDE (1)
V PENCIL DRAWER BACK (1)
A
B
C
D
E
F
G
H
J
K
L
M
N
O
P
Q
R
S
T
U
V
N
O
P
Q
R
Pae 3www.sauder.com/service431315

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
(EXTENSION SET SHOWN SEPARATED)
1EXTENSION RAIL - 6 2EXTENSION SLIDE - 6 3SHORT FILE
GLIDE - 2 4LONG FILE GLIDE - 4
5FRONT FILE
GLIDE  2
LARGE WOOD
DOWEL - 24
6SMALL WOOD
DOWEL - 30
7LARGE HIDDEN
CAM - 23
8
SMALL HIDDEN
CAM - 10
9CAM SCREW - 33 10 CUP HINGE - 2 11 PULL - 5 12
13 HINGE - 2 SHELF PIN - 4 14 15 BUMPER CARD - 1 APPLIQUE CARD - 2
16
GROMMET - 2
19
METAL BRACKET - 2
17 TIE PLATE - 2 18
Pae 4 www.sauder.com/service 431315

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
1-1/2" FLAT HEAD SCREW - 17
21
26 78" MACHINE SCREW  5
3/8" FLAT HEAD SCREW - 36
25
BLACK 1/2" PAN HEAD SCREW - 12
24
1/2" FLAT HEAD SCREW - 8
22 SILVER 1/2" PAN HEAD SCREW - 4
23
2" FLAT HEAD SCREW - 6
20
Pae 5www.sauder.com/service431315

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Pae 6 www.sauder.com/service 431315

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Push nine LARGE HIDDEN CAMS (8) into the BOTTOM (E),
and SKIRT (F).
å Turn three CAM SCREWS (10) into the SKIRT (F).
Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code. 1
E
F
Arrow
8
8
Arrow
Arrow
8
10
Pae 7www.sauder.com/service431315
Some assembly
(and snacks) required.

å Insert two LARGE WOOD DOWELS (6) into the SKIRT (F).
å Fasten the SKIRT (F) to the BOTTOM (E). Tihten three
HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the SKIRT insert
into the BOTTOM.
Step 2 1
6
6E
F
Surface with
HIDDEN CAMS
These surfaces should be even.
Pae 8 www.sauder.com/service 431315

Step 3
å Push two SMALL HIDDEN CAMS (9) into the BRACE (H).
1
HArrow
9
9
Arrow
Pae 9www.sauder.com/service431315

å Separate the EXTENSION SLIDES (2) from the EXTENSION RAILS (1) as shown in the upper diaram below. Be
prepared, the parts are reasy.
å Fasten two EXTENSION RAILS (1) to the UPRIGHT (C). Use six 3/8" FLAT HEAD SCREWS (25).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlared diaram. Then, slide the inner
cartride of the EXTENSION RAIL in to find the other holes that lines up with the holes in the UPRIGHT. Turn a SCREW
into these holes.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.
Step 4
C
Push the black lever and pull the SLIDE from the RAIL.
Use these holes.
1
2
Open end
3/8" FLAT HEAD SCREW
(6 used in this step)
25
1
1
Pae 10 www.sauder.com/service 431315
7