Sauder Pogo 414436 User manual

PLEASE CONTACT US
BEFORE RETURNING
YOUR UNIT TO THE STORE
1-800-523-3987
www.sauder.com
Made in the USA
Archbold, OH
NOTE: THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
English.................... Page 1-12
Français...............Pages 13-14
Espanol.............Páginas 15-16
Lot #: 354681 07 / 10 / 13
Date Purchased: ____________________
414436
Bookcase/Footboard
Pogo Collection

ASSEMBLY TOOLS REQUIRED
Hammer
No. 2 Phillips Screwdriver
Tip Shown Actual Size
TABLE OF CONTENTS
Part Identification.......................3
Hardware Identification .............4
Assembly Steps....................5-12
Français..............................13-14
Espanol...............................15-16
Safety .................................17-18
Warranty...................................19
Page 2 www.sauder.com/services 414436

PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked
letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help
identify similar parts.
A RIGHT END 1
B LEFT END 1
C UPRIGHT 1
D LOWER UPRIGHT 1
E TOP 1
F BOTTOM 1
G FRONT PANEL 1
H SHELF 1
I BACK 1
J SKIRT 1
K RAIL 1
L TOP MOLDING 1
Page 3
www.sauder.com/services414436
A
B
C
D
E
F
G
H
I
J
K
L

HARDWARE IDENTIFICATION
Screws are shown actual size. You may receive extra hardware with your unit.
SILVER 3/8" MACHINE SCREW - 4
97S
Page 4 www.sauder.com/services 414436
HIDDEN CAM - 13
1F CAM DOWEL - 13 2F
BLACK 1-7/8" FLAT HEAD SCREW - 2
2S
METAL PIN - 4
1R
GLUE - 1
8M
WOOD DOWEL - 4
15F
BROWN 1-1/2" FLAT HEAD SCREW - 4
14S
METAL BRACKET - 8
4G
TACK GLIDE - 4
12E
BROWN 7/16" LARGE HEAD SCREW - 16
6S
NAIL - 49
1N
CARD HOLDER - 2
21M
CARD SHEET - 1
40M

Look for this icon. It means a video
assembly tip is available at:
www.sauder.com/services/tips
1
1
S
t
e
p
Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
Push thirteen HIDDEN CAMS (1F) into the ENDS (A and B), LOWER UPRIGHT (D), BOTTOM (F), and SHELF (H). Then, insert
the metal end of a CAM DOWEL (2F) into each HIDDEN CAM.
Page 5
www.sauder.com/services414436
Do not tighten the HIDDEN CAMS in this step.
Arrow
(13 used)
Arrow
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
A
B
D
F
H
1F
2F
1F
2F

Fasten the SHELF (H) to the RIGHT END (A). Tighten two HIDDEN CAMS.
Fasten the LOWER UPRIGHT (D) to the SHELF (H). Tighten a HIDDEN CAM.
2
2
S
t
e
p
Page 6 www.sauder.com/services 414436
Caution
Risk of damage or
injury. Hidden Cams
must be completely
tightened. Hidden
Cams that are not
completely tightened
may loosen, and parts
may separate.
To completely tighten:
Start Tighten
Arrow
Arrow
Maximum
210 degrees
Minimum
190 degrees
A
D
H
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
Finished edge
Curved edge

Fasten the BOTTOM (F) to the RIGHT END (A) and LOWER UPRIGHT (D). Tighten two HIDDEN CAMS and use two BLACK
1-7/8" FLAT HEAD SCREWS (2S).
Fasten four METAL BRACKETS (4G) to RAIL (K). Use four BROWN 7/16” LARGE HEAD SCREWS (6S).
NOTE: Be sure the BRACKETS are even with the edges of the RAIL.
Fasten the CARD HOLDERS (21M) to the other surface of the RAIL (K). Use four SILVER 3/8" MACHINE SCREWS (97S).
Fasten the RAIL (K) to the RIGHT END (A) and SHELF (H). Use three BROWN 7/16" LARGE HEAD SCREWS (6S).
3
3
S
t
e
p
Page 7
www.sauder.com/services414436
A
D
F
Maximum
210 degrees
Minimum
190 degrees
Arrow
BLACK 1-7/8" FLAT HEAD SCREW
(2 used in this step)
2S
BROWN 7/16" LARGE HEAD SCREW
(7 used for the METAL BRACKETS)
6S
Surface with
HIDDEN CAMS
These holes
must be here.
K
K
4G
4G
4G
Surface with
more holes
H
21M
This is a tracking label.
Please do not remove.
SILVER 3/8" MACHINE SCREW
(4 used for the CARD HOLDERS)
97S

4
4
S
t
e
p
Page 8 www.sauder.com/services 414436
First, fill the holes in the FRONT PANEL (G) 1/4 to 1/2 full with GLUE (8M). Then, insert the WOOD DOWELS (15F) into the
holes. Wipe away the excess GLUE.
Now, fill the holes in the RIGHT END (A) 1/4 to 1/2 full with GLUE. Then, insert the WOOD DOWELS in the FRONT PANEL (G)
into these holes. Wipe away the excess GLUE.
Fill the holes 1/4 to 1/2 full with GLUE.
Inspect the parts thoroughly before
assembling. Disassembly of glued
parts is extremely difficult.
Caution
A
G
8M
15F
15F
Curved edge

5
5
S
t
e
p
Page 9
www.sauder.com/services414436
First, fill the holes in the LEFT END (B) 1/4 to 1/2 full with GLUE (8M). Then, insert the WOOD DOWELS (15F) in the FRONT
PANEL (G) into the holes in the LEFT END. Wipe away the excess GLUE.
Fasten the LEFT END (B) to the BOTTOM (F) and SHELF (H). Tighten four HIDDEN CAMS.
Fasten the RAIL (K) to the LEFT END (B). Use a BROWN 7/16” LARGE HEAD SCREWS (6S).
Insert four METAL PINS (1R) into the UPRIGHT (C).
Insert the METAL PINS (1R) in one end of the UPRIGHT (C) into the holes in the SHELF (H).
Maximum
210 degrees
Minimum
190 degrees
Arrow
8M
G
B
Surface without
HIDDEN CAMS
Curved edge
F
H
K
C
1R
Finished edge
BROWN 7/16" LARGE HEAD SCREW
(1 used for the METAL BRACKET)
6S

Fasten the TOP (E) to the ENDS (A and B). Tighten four HIDDEN CAMS.
NOTE: Be sure the METAL PINS in the UPRIGHT (C) insert into the holes in the TOP (E).
Fasten the TOP MOLDING (L) to the TOP (E). Use four BROWN 1-1/2" FLAT HEAD SCREWS (14S).
6
6
S
t
e
p
Page 10 www.sauder.com/services 414436
Maximum
210 degrees
Minimum
190 degrees
Arrow
C
E
L
Rounded edge
Curved edge
Surface with holes
BROWN 1-1/2" FLAT HEAD SCREW
(4 used in this step)
14S
A
B