Sauder Whitaker Point 429369 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
Enlish p 1-50
Français p 51-57
Español p 58-64
Lot # 573912 10/26/21
Purchased: __________________
Executive Desk
Whitaker Point Collection | Model 429369
Business or pleasure.
Works both ways.

Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
3
4-5
6
7-50
51-57
58-64
65-66
67
A LEFT END (1)
B RIGHT END (1)
C LEFT UPRIGHT (1)
D RIGHT UPRIGHT (1)
E TOP (1)
F BOTTOM (2)
G MODESTY PANEL (1)
H BACK (2)
J SMALL DRAWER FRONT (2)
K SMALL LEFT DRAWER SIDE (2)
L SMALL RIGHT DRAWER SIDE (2)
M SMALL DRAWER BACK (2)
N SMALL DRAWER BOTTOM (3)
O DRAWER FRONT (1)
P LEFT DRAWER SIDE (1)
Q RIGHT DRAWER SIDE (1)
R DRAWER BACK (1)
S LARGE DRAWER FRONT (1)
T LARGE LEFT DRAWER SIDE (1)
U LARGE RIGHT DRAWER SIDE (1)
V LARGE DRAWER BACK (1)
W LARGE DRAWER BOTTOM (1)
X SHELF (1)
Y DOOR (1)
Z KEYBOARD FRONT (1)
AA LEFT KEYBOARD SIDE (1)
BB RIGHT KEYBOARD SIDE (1)
CC KEYBOARD BACK (1)
DD KEYBOARD SHELF (1)
EE LEFT EXTENSION BLOCK (1)
FF RIGHT EXTENSION BLOCK (1)
Pae 2 www.sauder.com/service 429369
Part Identification

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
A
B
C
D
E
F
F
G
H
H
J
K
K
L
L
M
M
N
N
NO
P
Q
S
T
U
V
W
X
Y
Z
FF
BB
CC
DD
J
R
EE
AA
Pae 3www.sauder.com/service429369

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
(EXTENSION SET SHOWN SEPARATED)
1SHORT EXTENSION
RAIL - 8 2SHORT EXTENSION SLIDE - 8
(EXTENSION SET SHOWN SEPARATED)
3LONG EXTENSION
RAIL - 2 4LONG EXTENSION SLIDE - 2
5FILE GLIDE - 2 6FILE
HANGER  2
LARGE WOOD
DOWEL - 42
7SMALL WOOD
DOWEL - 30
8
LARGE HIDDEN
CAM - 42
9SMALL HIDDEN
CAM - 12
10 11 CAM SCREW - 54 DOOR STOP- 1
12
13 HINGE - 2 GROMMET
WITH CAP- 2
14 15 GROMMET - 4 METAL PIN - 4 16 PULL - 5 17
KNOB - 1
18 19 KEYBOARD
HINGE - 2 21 BUMPER CARD - 2
APPLIQUE CARD - 1
20
Pae 4 www.sauder.com/service 429369

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
2" FLAT HEAD SCREW - 4
22 1-1/2" FLAT HEAD SCREW - 20 23
1-1/8" FLAT HEAD SCREW - 4
24 25 78" MACHINE SCREW  1
SILVER 1/2" PAN HEAD SCREW - 4
26 BLACK 1/2" PAN HEAD SCREW - 2 27
28 12" MACHINE SCREW  10 1/2" FLAT HEAD SCREW - 8
29
3/8" FLAT HEAD SCREW - 62
30
Pae 5www.sauder.com/service429369

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Pae 6 www.sauder.com/service 429369

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Push eiht LARGE HIDDEN CAMS (9) into the LEFT
END (A) and LEFT UPRIGHT (C).
å Turn twelve CAM SCREWS (11) into the exact holes shown
in the LEFT END (A) and LEFT UPRIGHT (C).
Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
A
C
1
11
(12 used)
(8 used)
9
Arrow
Pae 7www.sauder.com/service429369

Step 2
Push the black lever and pull the SLIDE from the RAIL.
Use these holes.
1
2
Open end
Open end
å Separate the SHORT EXTENSION SLIDES (2) from the SHORT EXTENSION RAILS (1) as shown in the upper diaram
below. Be prepared, the parts are reasy.
å Fasten four SHORT EXTENSION RAILS (1) to the LEFT END (A) and LEFT UPRIGHT (C). Use twelve 3/8" FLAT
HEAD SCREWS (30).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlared diaram. Then, slide the inner
cartride of the EXTENSION RAIL in to find the other holes that lines up with the holes in the END and UPRIGHT. Turn
a SCREW into these holes.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.
A
1
1
1
1C
3/8" FLAT HEAD SCREW
(12 used in this step)
30
Pae 8 www.sauder.com/service 429369

Step 3
Push the black lever and pull the SLIDE from the RAIL.
Use these holes.
3
Open end
Open end
å Separate the LONG EXTENSION SLIDES (4) from the LONG EXTENSION RAILS (3) as shown in the upper diaram
below. Be prepared, the parts are reasy.
å Fasten two LONG EXTENSION RAILS (3) to the LEFT END (A) and LEFT UPRIGHT (C). Use eiht 3/8" FLAT
HEAD SCREWS (30).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlared diaram. Then, slide the inner
cartride of the EXTENSION RAIL in to find the other holes that lines up with the holes in the END and UPRIGHT. Turn
a SCREW into these holes.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.
A
C
3/8" FLAT HEAD SCREW
(8 used in this step)
30
3
4
Pae 9www.sauder.com/service429369
3

Step 4
å Push twelve LARGE HIDDEN CAMS (9) into one each of
the BOTTOMS (F) and BACKS (H).
F
H
1
9
Arrow
Arrow
9
(12 used)
Pae 10 www.sauder.com/service 429369
Some assembly
(and snacks) required.

å Insert two LARGE WOOD DOWELS (7) into the BACK (H).
å Push the BOTTOM (F) onto the LARGE WOOD
DOWELS (7) in the BACK (H).
Step 5
F
H
Surface with HIDDEN CAMS
Surface with HIDDEN CAMS
7
This HIDDEN CAM should
be closer to this ede.
Pae 11www.sauder.com/service429369

Step 6
å Insert four LARGE WOOD DOWELS (7) into the
LEFT END (A).
å Fasten the BOTTOM (F) and BACK (H) to the LEFT
END (A). Tihten six LARGE HIDDEN CAMS.
å NOTE: Be sure the LARGE WOOD DOWELS in the LEFT
END insert into the BOTTOM and BACK.
F
A
H
7
(4 used)
Surface with HIDDEN CAMS
Surface with HIDDEN CAMS
1
Pae 12 www.sauder.com/service 429369

å Insert four LARGE WOOD DOWELS (7) into the
BOTTOM (F) and BACK (H).
å Fasten the LEFT UPRIGHT (C) to the BOTTOM (F) and
BACK (H). Tihten six LARGE HIDDEN CAMS.
å NOTE: Be sure the LARGE WOOD DOWELS in the
BOTTOM and BACK insert into the LEFT UPRIGHT.
Step 7
F
H
C
7
(4 used)
1
Pae 13www.sauder.com/service429369

Step 8
å Push eiht LARGE HIDDEN CAMS (9) into the RIGHT
END (B) and RIGHT UPRIGHT (D).
å Turn twelve CAM SCREWS (11) into the exact holes shown
in the RIGHT END (B) and RIGHT UPRIGHT (D).
11
(12 used)
(8 used)
9
Arrow
1
B
D
Pae 14 www.sauder.com/service 429369

Step 9
Use these holes.
1
Open end
Open end
å Fasten one SHORT EXTENSION RAIL (1) each to the RIGHT END (B) and RIGHT UPRIGHT (D). Use six 3/8" FLAT
HEAD SCREWS (30).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlared diaram. Then, slide the inner
cartride of the EXTENSION RAIL in to find the other holes that lines up with the holes in the END and UPRIGHT. Turn
a SCREW into these holes.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.
B
D
1
3/8" FLAT HEAD SCREW
(6 used in this step)
30
Pae 15www.sauder.com/service429369
1

Step 10
å Push twelve LARGE HIDDEN CAMS (9) into the remainin
BOTTOM (F) and BACK (H).
F
H
1
9
Arrow
Arrow
9
(12 used)
Pae 16 www.sauder.com/service 429369

Step 11
å Insert two LARGE WOOD DOWELS (7) into the BACK (H).
å Push the BOTTOM (F) onto the LARGE WOOD
DOWELS (7) in the BACK (H).
F
H
Surface with HIDDEN CAMS
Surface with HIDDEN CAMS
7
This HIDDEN CAM should
be closer to this ede.
Pae 17www.sauder.com/service429369

Step 12
å Insert four LARGE WOOD DOWELS (7) into the
RIGHT UPRIGHT (D).
å Fasten the BOTTOM (F) and BACK (H) to the RIGHT
UPRIGHT (D). Tihten six LARGE HIDDEN CAMS.
å NOTE: Be sure the LARGE WOOD DOWELS in the RIGHT
UPRIGHT insert into the BOTTOM and BACK.
F
D
H
7
(4 used)
Surface with HIDDEN CAMS
Surface with HIDDEN CAMS
Pae 18 www.sauder.com/service 429369

å Fasten the DOOR STOP (12) to the RIGHT UPRIGHT (D).
Use two BLACK 1/2" PAN HEAD SCREWS (27).
å Insert four LARGE WOOD DOWELS (7) into the
BOTTOM (F) and BACK (H).
å Fasten the RIGHT END (B) to the BOTTOM (F) and
BACK (H). Tihten six LARGE HIDDEN CAMS.
å NOTE: Be sure the LARGE WOOD DOWELS in the
BOTTOM and BACK insert into the RIGHT END.
Step 13
F
D
H
B
7
12
(4 used)
BLACK 1/2" PAN HEAD SCREW
(2 used in this step)
27
1
Pae 19www.sauder.com/service429369

Step 14
å Insert four LARGE WOOD DOWELS (7) into the
MODESTY PANEL (G).
å Fasten the MODESTY PANEL (G) to the RIGHT
UPRIGHT (D). Use two 2" FLAT HEAD SCREWS (22).
å NOTE: Be sure the LARGE WOOD DOWELS in the
MODESTY PANEL insert into the RIGHT UPRIGHT.
å Fasten the LEFT UPRIGHT (C) to the MODESTY
PANEL (G). Use two 2" FLAT HEAD SCREWS (22).
å NOTE: Be sure the LARGE WOOD DOWELS in the
MODESTY PANEL insert into the LEFT UPRIGHT.
å Push two LARGE HIDDEN CAMS (9) into the
MODESTY PANEL (G).
1
Arrow
9
G
C
D
Surface with holes
7
(4 used)
2" FLAT HEAD SCREW
(4 used in this step)
22
22
Pae 20 www.sauder.com/service 429369