Sauder 535782 User manual

sauder.com
Storage Cabinet
Model
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
Share your journey!
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
You'll love what we
have in storage.
English pg 1-18
Français pg 19-21
Español pg 22-24
Lot # 535782 10/22/19
Purchased: __________________

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
Hammer
Not actual size
3
4
5-18
19-21
22-24
25-26
27
Page 2
Electric drill with 1/8" bit
(ONLY in indicated step)

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
M RIGHT END (1)
N LEFT END (1)
O UPRIGHT (1)
P TOP (1)
Q BOTTOM (1)
R SHELF (1)
S BACK (1)
T RIGHT DOOR (1)
U LEFT DOOR (1)
V ADJUSTABLE SHELF (4)
W VALANCE (2)
X SKIRT (1)
M
N
O
P
Q
R
S
T
U
V
W
X
V
V
V
W
Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
APPLIQUE - 30
26
SHELF SUPPORT - 16
30
FELT DISC - 4
32
FURNITURE TIPPING RESTRAINT KIT - 1
98
ANGLE BRACKET - 5
22
METAL BRACKET - 2
27
NAIL - 36
31
MAGNETIC CATCH - 2
28 STRIKE PLATE - 2 29
1/2" FLAT HEAD SCREW - 12
35
1-1/2" FLAT HEAD SCREW - 40
33
1/2" PAN HEAD SCREW - 14
16
3/4" MACHINE SCREW - 4
34
Page 4
PULL - 2
25
HINGE - 6
23
SMALL 1/2" FLAT HEAD SCREW - 4
40
5/8" PAN HEAD SCREW - 4
38

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/service/tips
åAssemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
åFasten five ANGLE BRACKETS (22) to the SKIRT (X). Use
five 1/2" PAN HEAD SCREWS (16).
åNOTE: Be sure the edges of the ANGLE BRACKETS are
even with the edges of the SKIRT.
åFasten the MAGNETIC CATCHES (28) to the
BOTTOM (Q). Use four 5/8" PAN HEAD SCREWS (38).
Page 5
22
X
Q
1/2" PAN HEAD SCREW
(5 used for the ANGLE BRACKETS)
16 22
22
28
Some assembly
(and snacks) required.
5/8" PAN HEAD SCREW
(4 used for the MAGNETIC CATCH)
38

å Fasten the SKIRT (X) to the BOTTOM (Q). Use three 1/2"
PAN HEAD SCREWS (16) through the ANGLE BRACKETS
on the SKIRT and into the BOTTOM.
Step 2
Page 6
X
Q
1/2" PAN HEAD SCREW
(3 used in this step)
16
Surface without
MAGNETIC CATCHES

å Open the FURNITURE TIPPING RESTRAINT KIT (98)
and fasten the SAFETY STRAP to the TOP (P). Use the
short screw through the hole in the strap and into the top
surface of the TOP (P).
å Fasten the VALANCES (W) to the TOP (P). Use eight
1-1/2" FLAT HEAD SCREWS (33).
Step 3
Page 7
98
SAFETY STAP
SHORT SCREW
P
P
W
W
1-1/2" FLAT HEAD SCREW
(8 used in this step)
33
The SAFETY STRAP
should be here.

å Fasten two METAL BRACKETS (27) to the UPRIGHT (O).
Use two 1/2" PAN HEAD SCREWS (16).
å NOTE: Be sure the edges of the METAL BRACKETS are
even with the top edge of the UPRIGHT.
å Fasten the BOTTOM (Q) to the UPRIGHT (O). Use two
1-1/2" FLAT HEAD SCREWS (33).
Step 4
Page 8
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
Q
X
O
27
Top edge
1-1/2" FLAT HEAD SCREW
(2 used in this step)
33
1/2" PAN HEAD SCREW
(2 used in this step)
16

Step 5
Page 9
åFinish fastening the BOTTOM (Q) to the SKIRT (X). Use
two 1-1/2" FLAT HEAD SCREWS (33).
åFasten the SHELF (R) to the UPRIGHT (O). Use two 1-1/2"
FLAT HEAD SCREWS (33)
åFinish fastening the SHELF (R) to the UPRIGHT (O). Use
two 1/2" PAN HEAD SCREWS (16) through the METAL
BRACKETS on the UPRIGHT and into the SHELF.
åThen, peel four APPLIQUES (26) from the applique card
and stick them over the heads of the SCREWS (33).
Q
O
R
Peel the APPLIQUES
from the applique card.
26
X
26
26
1-1/2" FLAT HEAD SCREW
(4 used in this step)
33
1/2" PAN HEAD SCREW
(2 used in this step)
16

Step 6
Page 10
Now might be a
good time to refresh
your drink.
å Fasten the LEFT END (N) to the TOP (P), BOTTOM (Q),
SHELF (R), VALANCES (W), and SKIRT (X). Use thirteen
1-1/2" FLAT HEAD SCREWS (33).
å Finish fastening the LEFT END (N) to the SKIRT (X).
Use a 1/2" PAN HEAD SCREW (16) through the ANGLE
BRACKET on the SKIRT and into the LEFT END.
Q
R
W
X
P
N
W
1-1/2" FLAT HEAD SCREW
(13 used in this step)
33
1/2" PAN HEAD SCREW
(1 used in this step)
16
The SAFETY STRAP
on the TOP should
be near the floor.