Sauder Barrister Lane Hutch 418295 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-17
Français pg 18-19
Español pg 20-21
Lot # 366595 11/25/14
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Hutch
Barrister Lane Collection | 418295
For things 'n such.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Hammer
Not actual size
3
4
5-17
18-19
20-21
22
23
418295 www.sauder.com/servicesPage 2
Short Screwdriver
Skip the power trip.
This time.

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
D TOP (1)
E SHELF (1)
F RIGHT BACK (1)
G LEFT BACK (1)
H DIVIDER (3)
I SKIRT (1)
J FRONT MOLDING (1)
K RIGHT MOLDING (1)
L LEFT MOLDING (1)
418295www.sauder.com/services Page 3
A
B
C
D
E
F
GH
I
J
K
L
H
H

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
418295 www.sauder.com/servicesPage 4
BLACK 9/16" LARGE HEAD SCREW - 3
1S
BLACK 1-1/4" FLAT HEAD SCREW - 9
7S
BLACK 1-7/8" FLAT HEAD SCREW - 3
2S
36P CAM COVER - 10
MOLDING
CONNECTOR - 2
17F
METAL PIN - 11
1R
NAIL - 36
1N
HIDDEN CAM - 12
1F CAM DOWEL - 12 2F

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push twelve HIDDEN CAMS (1F) into the ENDS (A and B),
UPRIGHT (C), SHELF (E), and SKIRT (I). Then, insert the
metal end of a CAM DOWEL (2F) into each HIDDEN CAM.
418295www.sauder.com/services Page 5
A
B
C
E
I
Arrow
1F
2F
(12 used)
Arrow
1F
2F
Do not tighten the HIDDEN CAMS in this step.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow

å Tap two MOLDING CONNECTORS (17F) into the notches
in the MOLDINGS (J, K, and L).
Step 2
418295 www.sauder.com/servicesPage 6
K
J
17F
17F
L
Use your hammer to tap the MOLDING CONNECTOR (17F) into the notches in the MOLDINGS.
Flat end
Flat end

å Turn the MOLDINGS (J, K, and L) over and fasten them
to the TOP (D). Use nine BLACK 1-1/4" FLAT HEAD
SCREWS (7S).
Step 3
418295www.sauder.com/services Page 7
D
K
J
L
Surface with holes
Remember:
Righty tighty.
Lefty loosey.
Finished surface
Finished surface
Rounded edge
BLACK 1-1/4" FLAT HEAD SCREW
(9 used in this step)
7S

å Fasten the RIGHT END (A) to the RIGHT MOLDING (K).
Tighten two HIDDEN CAMS.
Step 4
418295 www.sauder.com/servicesPage 8
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
A
K
J
Curved edge
Surface with
HIDDEN CAMS
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

å Insert three METAL PINS (1R) into the holes shown in the
TOP (D).
å Slide the DIVIDERS (H) onto the METAL PINS (1R) in the
TOP (D).
å Now, insert six METAL PINS (1R) into the other end of the
DIVIDERS (H).
Step 5
418295www.sauder.com/services Page 9
D
H
H
H
J
1R
1R
All curved edges should face
the FRONT MOLDING (J).

å Fasten the SHELF (E) to the RIGHT END (A). Tighten two
HIDDEN CAMS.
å NOTE: Be sure the METAL PINS in the DIVIDERS (H)
insert into the holes in the SHELF.
Step 6
418295 www.sauder.com/servicesPage 10
A
H
H
H
E
Surface with
HIDDEN CAMS
Arrow
Minimum
190 degrees
Maximum
210 degrees
Finished edge