Sauder 414675 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-23
Français pg 24-26
Español pg 27-29
Lot # 358975 01/15/14
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Side Table
Carson Forge Collection | Model 414675
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Gets on your couch’s
good side.

Table of Contents Assembly Tools Required
3
4
5-23
24-26
27-29
30
31
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
414675 www.sauder.com/servicesPage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D SHELF/BOTTOM (2)
E PULL-OUT SHELF (1)
F BACK (1)
G DOOR (1)
H ADJUSTABLE SHELF (1)
I RIGHT FRONT LEG (1)
J LEFT FRONT LEG (1)
K REAR LEG (2)
L PULL-OUT MOLDING (1)
M LOWER END MOLDING (2)
N UPPER END MOLDING (2)
Now you know
our ABCs.
414675www.sauder.com/services Page 3
A
B
C
D
E
F
G
H
I
J
K
L
M
N
D
K
N
M

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
414675 www.sauder.com/servicesPage 4
FOOT - 4
10E
8E CORNER ACCENT - 2
(EXTENSION SET SHOWN SEPARATED)
OEXTENSION RAIL - 2 PEXTENSION SLIDE - 2
GOLD 1" MACHINE SCREW - 1
50S
14H HINGE - 2
BLACK 1/2" FLAT HEAD SCREW - 4
11S
BLACK 9/16" FLAT HEAD SCREW - 8
32S
CAM SCREW - 6
8F
SILVER 1/2" MACHINE SCREW - 2
38S
DOOR STOP - 1
4I
BROWN 1" FLAT HEAD SCREW - 4
12S
GOLD 5/16" FLAT HEAD SCREW - 4
3S
NAIL - 18
1N
CAM DOWEL - 12
2F
HIDDEN CAM - 18
1F
CAM COVER - 3
12P METAL PIN - 4
1R RUBBER SLEEVE - 4 2R
TACK GLIDE - 4
12E
BLACK 2-1/4" FLAT HEAD SCREW - 4
26S
52K KNOB/BACKPLATE - 1

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty carton
to avoid scratching your unit or the floor.
å Push eighteen HIDDEN CAMS (1F) into the ENDS (A and B),
SHELF/BOTTOMS (D), and PULL-OUT SHELF (E). Then, insert
the metal end of twelve CAM DOWELS (2F) into the HIDDEN
CAMS in the ENDS and SHELF/BOTTOMS.
414675www.sauder.com/services Page 5
E
1F
Do not insert
CAM DOWELS
into these edges.
A
B
D
D
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tighten the HIDDEN
CAMS in this step.
Arrow
1F
2F
Arrow
(18 used)
(12 used)
Arrow
Hole
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1424
to watch a video on how to assemble your unit.

Step 2
å Turn six CAM SCREWS (8F) into the FRONT LEGS (I and J)
and PULL-OUT MOLDING (L).
414675 www.sauder.com/servicesPage 6
8F
I
J
L
(6 used)
Remember:
Righty tighty.
Lefty loosey.

å Fasten a CORNER ACCENT (8E) to the FRONT LEGS (I and J).
Use two SILVER 1/2" MACHINE SCREWS (38S).
Step 3
414675www.sauder.com/services Page 7
I
J
8E
8E
SILVER 1/2" MACHINE SCREW
(2 used in this step)
38S

Step 4
å Fasten the FRONT LEGS (I and J) to the ENDS (A and B).
Tighten four HIDDEN CAMS.
414675 www.sauder.com/servicesPage 8
I
J
A
B
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
1
2
Angled edge
Angled edge
These edges should be even.
These edges should be even.

å Carefully turn your ENDS (A and B) over.
å Turn eight BLACK 9/16" FLAT HEAD SCREWS (32S) into the
ENDS (A and B) until the shoulders of the SCREWS rest on the
surfaces of the ENDS.
å Slide the END MOLDINGS (M and N) onto the ENDS (A and B)
until they are against the FRONT LEGS (I and J). Line up the
grooves in the MOLDINGS over the heads of the SCREWS in
the ENDS.
Step 5
414675www.sauder.com/services Page 9
A
B
I
J
N
M
N
M
Surface without
HIDDEN CAMS
Surface without
HIDDEN CAMS
These edges
should be even.
Apply pressure with your hands
as you guide the MOLDINGS over
the SCREWS and onto the ENDS.
BLACK 9/16" FLAT HEAD SCREW
(8 used in this step)
32S
Shoulder

Step 6
å Fasten the REAR LEGS (K) to the ENDS (A and B). Use
four BLACK 2-1/4" FLAT HEAD SCREWS (26S).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
414675 www.sauder.com/servicesPage 10
A
B
K
K
Flat edge
Flat edge
BLACK 2-1/4" FLAT HEAD SCREW
(4 used in this step)
26S