Sauder Costa Credenza 422984 User manual

sauder.com
Credenza
Costa Collection | Model 422984
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-28
Français pg 29-32
Español pg 33-36
Lot # 547057 05/05/20
Purchased: __________________
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-523-3987.
Customer Service is available Monday-Friday - 8:30 a.m. to 5 p.m. EST (except holidays)
Sauder.com
Share your journey!
Sit and surf.

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
2-3
4
5-28
29-32
33-36
37-38
39
Hammer
Not actual size
Now you know
our ABCs.
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C END MOLDING (2)
D PRINTER SHELF (1)
E SHORT BOTTOM MOLDING (2)
F RIGHT BOTTOM (1)
G BOTTOM (1)
H RIGHT FRONT LEG (2)
I BOTTOM MOLDING (1)
J ADJUSTABLE SHELF (2)
K PRINTER SHELF MOLDING (1)
L RIGHT UPRIGHT (1)
M LEFT UPRIGHT (1)
N CENTER BACK (1)
O LEFT REAR LEG (1)
P LEFT FRONT LEG (2)
Q LEFT CENTER LEG (1)
R LEFT BOTTOM (1)
S RIGHT REAR LEG (1)
T RIGHT CENTER LEG (1)
U BACK (2)
V TOP (1)
W LEFT DOOR (1)
X RIGHT DOOR (1)
422984 www.sauder.com/servicePage 2
Nail Holder (provided)
Tape Measure
Electric drill with 3/16" bit
(ONLY in indicated step)

Part Identification
422984www.sauder.com/service Page 3
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
U
J
E
H
P
C

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
422984 www.sauder.com/servicePage 4
BB LEFT DRAWER
SLIDE - 1
RIGHT CABINET
RAIL - 1
YLEFT CABINET
RAIL - 1
ZRIGHT DRAWER
SLIDE - 1
AA
BLACK 1-1/8" MACHINE SCREW - 2
21S
GROMMET CAP - 1
1P
18S BROWN 1" FLAT HEAD SCREW - 4
7F TWIST-LOCK®
FASTENER - 20
CORD CLIP - 1
4P
3S GOLD 5/16" FLAT HEAD SCREW - 4
METAL PIN - 8
1R
BLACK 1/2" FLAT HEAD SCREW - 8
11S
BLACK 9/16" FLAT HEAD SCREW - 4
32S
CAM SCREW - 27
8F
DOOR STOP - 2
4I
WOOD DOWEL - 16
15F
GROMMET - 1
10P
NAIL - 52
1N
HIDDEN CAM - 27
1F
RUBBER SLEEVE - 8
2R
14H HINGE - 4 KNOB SET - 2
167K
METAL BRACKET - 1
4G
BLACK 9/16" LARGE HEAD SCREW - 1
1S
GLUE - 2
177M

Step 1
422984www.sauder.com/service Page 5
Do not tighten the TWIST-LOCK® FASTENERS in this step.
(20 used)
7F
å Assemble your unit on a carpeted floor or on the empty carton to
avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (7F)
into the large holes in the ENDS (A and B). Repeat this step for
the BOTTOMS (F, G, and R) and UPRIGHTS (L and M).
A
B
STOP
If you purchased
the 422983 Hutch,
assemble that unit
first.
Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code. 2

Step 2
422984 www.sauder.com/servicePage 6
Arrow
Arrow
1F
Hole
å Push twenty-seven HIDDEN CAMS (1F) into
the ENDS (A and B), PRINTER SHELF (D),
and UPRIGHTS (L and M).
1F
Arrow
A
B
L
M
D
(27 used)
Some assembly
(and snacks) required.
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
1

Step 3
422984www.sauder.com/service Page 7
8F
å Turn twenty-seven CAM SCREWS (8F) into the PRINTER
SHELF MOLDING (K) and LEGS (H, O, P, Q, S, and T).
H
K
O
P
Q
S
T
H
P
(27 used)
1

Step 4
422984 www.sauder.com/servicePage 8
å Turn four BLACK 9/16" FLAT HEAD SCREWS (32S) into
the ENDS (A and B) until the shoulders of the SCREWS
rest on the surfaces of the ENDS.
å NOTE: Do not overtighten the SCREWS.
å Slide the END MOLDINGS (C) onto the ENDS (A and B).
Line up the grooves in the MOLDINGS over the heads of
the SCREWS in the ENDS.
å NOTE: If the MOLDING comes up o of the SCREWS,
remove it and slide it on again. The MOLDINGS should be
even on both edges of the ENDS.
Apply pressure with your hands
as you guide the MOLDINGS over
the SCREWS and onto the ENDS.
A
B
Surface without
HIDDEN CAMS
Surface without
HIDDEN CAMS
C
C
BLACK 9/16" FLAT HEAD SCREW
(4 used in this step)
32S
Shoulder

Step 5
422984www.sauder.com/service Page 9
Inspect the parts thoroughly before
assembling. Disassembly of glued
parts is extremely dicult.
Caution
!
å First, fill the exact two holes shown in the RIGHT END (A) 1/4 to 1/2 full with
GLUE (177M). Then, insert two WOOD DOWELS (15F) into the holes. Wipe away
the excess GLUE.
å NOTE: Be sure to position the parts exactly as shown.
å Now, fill the holes in the LEGS (H and S) 1/4 to 1/2 full with GLUE (177M).
å Fasten the LEGS (H and S) to the RIGHT END (A). Tighten six HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the RIGHT END insert into the LEGS.
Wipe away the excess GLUE.
15F
A
H
These surfaces
should be even.
Edge with
TWIST-LOCK®
FASTENERS
1
2
Edge without hole
Surface with
HIDDEN CAMS
S
Edge without hole
These surfaces
should be even.
177M
Fill the holes 1/4 to 1/2 full with GLUE.
1

Step 6
422984 www.sauder.com/servicePage 10
Inspect the parts thoroughly before
assembling. Disassembly of glued
parts is extremely dicult.
Caution
!
15F
B
O
These surfaces
should be even.
Edge with
TWIST-LOCK®
FASTENERS
Edge with hole
Surface with
HIDDEN CAMS
P
These surfaces
should be even.
å First, fill the exact two holes shown in the LEFT END (B) 1/4 to 1/2 full with
GLUE (177M). Then, insert two WOOD DOWELS (15F) into the holes. Wipe away
the excess GLUE.
å NOTE: Be sure to position the parts exactly as shown.
å Now, fill the holes in the LEGS (O and P) 1/4 to 1/2 full with GLUE (177M).
å Fasten the LEGS (O and P) to the LEFT END (B). Tighten six HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the LEFT END insert into the LEGS. Wipe
away the excess GLUE.
Edge with hole
15F
177M
Fill the holes 1/4 to 1/2 full with GLUE.
1