Sauder Avenue Eight 416505 User manual

Dresser
Avenue Eight Collection I416505
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Calll - 800-523-3987.
NOTE: THIS IN STR UCTI ON
BOO KLET CONTAINS IMPORTANT
SAFETY INF ORMATION.
PLEASE READ AND
KEEP FOR
FUTURE RE F ERENCE.
English pg 1 -22
Fran~ais pg 23-25
Espanol pg 26-28
Lot# 362388
Purchased:
06/09/14
Be su re to give us a ring before
making any returns. 1-
800 - 523 - 3987

Table of Contents Assembly Tools Required
Part Identification
' While not all pa rts are labeled, some of the pa rt s will have a label or an inked le tter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RI GHT E ND (1) L ARGE D RAWE R FR ONT (4) D60 DRAWE RB ACK (2)
B
LEFT EN D (1)
L FRONT MOL DI NG (1) D171 LARG E DRAWE R BACK (4)
--
---
c UP RI GHT (1) M RIGHT MOLDI NG (1) D2 31 LARG E LE FT DRAWER SID E(4)
~
D T OP (1) N L EFT MOLDING (1) D237
LARGE RIGHT DRAWER SI DE (4)
----
--
E
BOTTOM (1)
0
DRAW ER FRON T (2)
D245
RIGHT DRAWER SID E (2)
F
BACK (1)
R P
LI N TH (2)
D246
L EFT DRAWER SI DE (2)
--- - - -
G
DRAWER BRACE (6) s BOTTOM MOLD I NG (1)
D979 D
RAW ER B OTTOM (6)
H
BASE (1)
T DR
AWE R FRONT MOL DI NG (2)
Page 2 416505 www.sa uder. com/ services

Part Identification
0
.(;::'
www.sa uder.com/ services
.C;::l
. @)
416505
Now you know ~~
our ABCs. EJB
Page 3

Hardware Identification
' Screws are shown actual size. You may receive extra hardware with your unit.
~ UNIVERSAL Q DRAWER RIG HT - 6 Q DRAWER LEFT - 6
~ CABINET RA IL - 12 ~ ~
M HIDDEN
V CAM - 10
Q MOLD I NG
V CONNECTOR - 2
Q LARGE DRAWER
V FRONT BRACKET - 4
0 CAM DOWEL- 4
@ TIE PLATE - 2
~
@ KNOB -12
w
M T WIST-LOCK ®
V FASTENER - 12
(;";;\METAL
V BRACKET-S
@ WARN I NG LABEL - 1
S er i o..,so r l• tal <: no$hin ;injori nu nqccu r
hom fu r nhu1 ~ tlp- o11er. To lul p preveot
• Pl,io: e ~lMe:lt~(:<M,.,thvlov""'tdro~...,.~
•Ur .t.<.s~ o flc...fly~VJ-.!d lolooO.X.Or o ....-o;l<>iot,JI>o l(.t
U\ TV.:.~Oihri> r OO.oY) objtlcuon ~c. t ll-uprOOuct
• ,.._...,...l,..,<:llfY(Iorrb~ · ~(,(I\JI«<·'"' ~
door~ Of ~lod<.n.
• Ne-"to ~ln<.I·"-·Ofloil~--illllme
• l f~Wi lhldrll-ntl!rlX k1 r;I<YI\.:bOO t
d.o·.,•t lllr r.,-o"V<c,.
Un rA ttp- ovtrr t$ lr'*'htn;oyonlyted.o<:t, butl'lOt
elimor! l lt,lhe rl~koftij) •O>Y t<'.
This iso ptrm-nt klbtl Do,.,ro uemp r ro re rnt1H!
04/lO .332Z9(;
(Refer to Step 17 for proper
location and application)
0 FOOT-1
u
@ CAM SCREW - 6
Q DRAWER FRONT
V BRACKET - 2
8 WASHER-1
@
@ SAFETY STRAP - 1
~ SAFETY DRYWAL L
~ ANCHOR - 1 G
NAIL-60
0 ~=======:J;:I>
Locate this nylon SAFETY
STRAP (60M) to be used
later in assembly. Do not
accidentally throw
away.
Page 4 416505
- -- - ~ -- ~- -~ - - - -- - - --
www.sauder.com/services

Hardware Identification
' Screws are shown actual size. You may receive extra hardware with your unit.
0 BL ACK 9/16"L ARGE HEAD SCREW -45
cw ~
§ GOLD 5/16" FLAT HEAD SCREW -48
@ ~
@BROWN 1" FLAT HEAD SCREW- 6
@ ~
8 SILVER 1/2" MACH I NE SCREW - 8
® ~
www.sauder.com/services
- @BLACK 1-7/8" FLAT HEAD SCREW - 2
©
@BLACK 1-1/4" FL AT HE AD SCREW - 9
© ~
8 BLACK 1-9/16" FLAT HEAD SCREW - 30
(±) [:r=lnnnnD
8 GOLD 1" MACHINE SCREW- 4
88 @ll-\1\\\\~
41 6505 Page 5

Step 1
' Assemble your unit on a carpeted floor or on the empty
ca rt on to avoid scratching your unit or the floor.
'
To begin assembl y, push a SAUDER TWIST-LOCK®
FASTENER (7F) into the large holes in the ENDS (A and B).
Repeat this step for the UPRIGHT (C) and BOTTOM (E).
Look for this icon. It means a
video assembly tip is available at
www.sauder.com/ services/ tips
Do not tighten the TWIST-LOCK ® FASTENERS in this st ep.
-. -
(12 used)
Page6
416505 www.sauder.com/services

Step 2
' Push four HIDDEN CAMS ( 1F ) into the BOTTOM (E).
Then, insert the metal end of a CAM DOW EL (2F) into
each HIDDEN CAM.
(4 used)
www.saude
r. com/ se rvices
Do not tighten the HIDDEN CAMS in this step.
0
Arrow
Insert the metal end of the CAM
DOWEL into the HI DDEN CAM.
416505 Page 7

Step 3
• Tap two MOLDING CONNECTORS (17F) into the notches
in the MOLDINGS (L, M, and N).
Use your hammer to tap the MOLDING CONNECTORS (17F) into the notches in the MOLDINGS.
Flat end
4 16505
Page8
Flat end
I
I
I
I
\
I
, I
\
www.sauder.com/services
\
I
I
I
I

Step 4
Fasten t he MOLDINGS (L, M, and N) to the TOP (D). Use
n in e BLACK 1-1 /4" FLAT HEAD SCREWS (7S).
Finished surface
Long flat edge
www.sauder.com/services 41
65 05
T
'I
Remember:
Righty tighty.
Lefty loosey.
BL ACK 1-1/4" FLAT HEAD SCREW
(9 used in this step)
Page 9

Step 5
' Fasten the UN I VERSAL CABINET RA I LS* (35AA) to the
ENDS (A and B) and both surfaces of the UPR I GH T (C).
Use twenty-four GOLD 5/16" FL AT HEAD SCR E WS (3S)
through holes #1 and #3.
' *patent pending glide system
Edge with
TWIST -L OCK ®
FASTENER
GOLD 5/16" FLAT HEAD SCREW
(24 used in this ste p)
Page 10 I
I
416505
Edge with
TWIST-LOCK "
FASTENER
Finished edge
www.s auder.com/services

Step 6
'
'
Fasten the LEFT END (B) to the L EFT MOLDING (N) on
the T OP (D). Tighten t wo TW I ST- L OCK ® FASTENERS.
Fasten the U PRI GH T (C) to t he TOP (D). Tighten two
TWI ST- L OC K® FASTENERS.
A_ caution
Do not stand the u ni t upright without the
BACK fastened. The unit may collapse.
Edge with
TWI ST-LOCK "'
F ASTENER
www.sa uder.com/services
How to use the SAUDER TWIST - LOCK . FASTENER
• 1. Insert the dowel end of the FA S TE NERinto t he hole of
the adjoining par
t.
NO T E: The dowel end of the FASTENER must re ma in fully
inserted in the hole of the adjoining part while locking the
FASTENER.
2. Tighten the FASTENER with a Phillips sc rewdriver as
tight as possible.
Su rface without
TWIST-LOC K '"
FASTENER
416505
Dowe l end
Page 11

Step 7
' Fasten th e BOTTOM (E) to the LEFT END (B) .Tighten two
TWI ST-LOCK "' FASTENERS .
' F as ten the BOTTOM (E ) to the UPRIGHT (C). Use two
BLACK 1-7/8" FLAT HEAD SC REWS (2S).
' F as ten th e RIGHT END (A) to the BOTTOM (E) and RIGHT
MOLDING ( M). Ti g hten four TWIST-LOCK ., FASTENERS.
Edge with HIDDEN CA MS
Pa ge 12
BL ACK 1-7/8" FL AT HEAD SCR EW
(2 used in this step)
416505
0
Edg ewith
TWIST - LO CK '"
FA S TENER
www.sauder.com/ services

Step 8
' Fasten two METAL BRACKETS (4G) to the BOTTOM (E). Use two
BLACK 9/ 1 6" LARGE HEAD SCR E WS (1S).
' NO TE : Be sure the edges of the M ET AL BRACKE TS are even with the
edge of th e BOTTOM.
' F asten the BOTTOM MOLDING (S) to the BOTTOM (E). Tighten four
HIDDEN CAMS.
' Fasten the PLINTHS (R) to th e ENDS (A and B) and BOTTOM (E) .
Tighten two
TWIST-LOCK "' FASTENERS and use two BL ACK 9/16"
L ARGE HEAD SCREWS (1S).
. ACaution
Risk of damage or
injury. HID DE N CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
www.sauder.com/services
Curved edge
Start
Arrow
416505
BLACK 9/16" LARGE HEAD SCREW
(4 used for the METAL BRACKETS)
Tighten
Maximum
210 degrees
Curved edge
Arrow
Page 13

Step 9
' Fasten six METAL BRACKETS (4G) to the BASE (H). Use
six BLACK 9/16" LARGE HEAD SCREWS (1S).
' NOTE: Be sure the edges of t he METAL BRACKETS are
even with the edge of the BASE.
' Fasten the BASE (H) to the BOTTOM (E). Use six BLACK
9/16" LARG E HEAD SCREWS (1S) through the METAL
BRACKETS and into the BOTTOM.
BLACK 9/16" LARGE HEAD SCREW
(12 used in this step)
Page 14
416505 www.sauder.com/services

Step 10
' Car efully turn yo ur unit over onto its front edges. Unfold the BACK (F)
and lay it over your unit.
' Make equal margins al ong all four edges of the BACK (F). Push on
opposite corners of your unit if needed to make it "square".
' Fasten
the BACK (F) to your unit using the NAILS (1N).
' NOTE: Be sure to tap NA ILS into the holes that line up over
th e UPRIGHT (C).
' NOTE: Perforations have been provided for access through th e BACK.
Carefully
cut out the holes neede d.
' Push the FOOT (3E) into the hole in the BOTTOM (E) .
' Fasten the TIE PLATES (3G) to the BASE (H) and·PLINTHS (R). Use
four BLACK 9/ 16" LARGE HEAD SCREWS (1 S).
£caution
Do not sta nd t he unit uprig ht without the
BACK fas tened. Th e unit m ay co llap se.
0 ~ ~=== :::::t::l> -e
NA IL
(60 us ed in this s tep)
These ho le smust line up
'- '-
'- '-
'- '-
'-
'-
'- '-
'- '-
'- '-
'-
'-
0
'- '- '-
'- '- '-
'- .
. '- '- '-
0
www.saud e r.c om/ serv ice s
'-
'-
'-
over the UPRIGHT (C ).
'-
'-
'-
'- '- '-
'-
'-
'-
'-
41 6505
'-
'-
'-
'-
'-
'-
Cut-out (used for the SAFE TY STRAP)
'-
'-
'- '-
Cut-out (u s ed for mirror)
BL AC K9 /1 6" LARGE HEAD S CREW
(4 us ed for the TIE PLATE S)
Pa ge 15

Step 11
' Turn six CAM SCREWS (SF) into the DRAWER FRONTS (I an d 0).
' Push six HIDDEN CAMS (1F) into the DRAWER BRACES (G).
(6 used)
Do not tighten the HIDDEN CAMS in this step.
Page 16
416505
r--~"
, Arrow
~ -
Hole
The arrow in the HIDDEN
CAM must point toward the
hole
in the edge of the board.
www .sauder.com/services

Step 12
••
' Fas t en the DRAWER FRON T MOLDINGS (T) to the
DRAWER F RON TS (0). Use six BROW N1" FLAT
HE AD SCR E WS (12S).
Rounded edge
Finished surface
-· Rounded edge
Finished surface
www.sauder.com/services 416505
Don't w orr y. It isn't
Ro me.This can be built
in a
day.
BROWN 1" F LAT HEAD SCREW
(6 used in this step)
Page 17

Step 13
' Pull the DRAWER FRONT BRACKETS (8G) apar t and slide them into the grooves
in the DRAWER SID ES(D245 and D246). You may need to gently tap them in
with a hammer.
' NOTE: Th e DRAWER F RONT BRACKE TS are marked "R H"and "LH" for
easy identification.
' Fasten the DR AWER FRONT (0) to the DRAWER FRONT BRACKETS (8G). U se
four BLACK 9/16" LARGE HEAD SCREWS (1S).
' Slide the DRAWER BO T TOM (D979) into the grooves in the DRAWER
SIDES (D245 and D246) and DRAWER FRONT (0).
' Repeat this step for the other drawers. Use the LAR GE DRAW ER FRONT
BRACKETS (9G) for the large drawers.
Page 18 416505
BL AC K 9/16" LARGE H EAD SCREW
(24 use d in this s tep)
With the palm of your hand ,
tap the DRAWER BOTTOM
down into the gr oove.
www.sauder.com/services

Step 14
' Fasten a DRAWER BRACE (G) to the DRAWER FR ONT (0). Tighten one HIDDEN CAM.
' Fasten the DRAWER BACK (D60) to the DRAWER BRACE (G) and DRAWER SI DES (D245
and
D24 6) . Use five BLACK 1 -9/ 16" FLAT HEAD SCREWS (30S).
' N OTE: Be sure the D RAW ER BOTTOM (D979) inserts into the groove in the
D RAW ER BACK (D6 0).
' Repeat th is step f or t he other drawers using the L ARGE
DRAWER BACK (D171) for the LARGE DR AWERS.
1li] - ~
2
www.sauder. com/ se rvices 416505
Start each screw a few turns before
completely tightening any of them.
·® ~
BL ACK 1-9/16" FLAT HEAD SCREW
(30 used in this step)
Page
19

Step 15
' Fasten the DRAWER RIGHT (35AC) and DRAWER LEFT (35AD)
to the DRAWER SIDES (D245 and D24 6). Use four GOLD 5/16"
FLAT HEAD SCREWS (3S) through holes #1 and #2.
' NOTE: The parts are marked "DRAWER RIGHT" and "DRAWER
LEFT" for easy identification.
' ~OTE: Th e gli des are not intended to rotate.
' Fasten two KNOBS (42K) to the DRAWER FRONT (0). Use two
GOLD 1" MACHINE SCREWS (50S).
' Repeat this step for t he other drawers. Use the SILVER 1/2"
MACHINE SCREWS (38S) for the KNOBS on the large drawers.
Glide end
1
GO LD 1" MACHINE SCREW
(4 used for the DRAWER FRONTS)
S ILVER 1/2" MACHINE SCREW
(8 used for the LARGE DRAWER FRONTS)
Page 20
GOLD 5/16 " FLAT HEAD SCREW
(24 used for the GLIDES)
416505
Glide end
1
www.sauder.com/services