Sauder 413123 User manual

PLEASE CONTACT US
BEFORE RETURNING
YOUR UNIT TO THE STORE
1-800-523-3987
www.sauder.com
Made in the USA
Archbold, OH
NOTE: THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Lot #: 357469 11 / 15 / 13
Date Purchased: ____________________
English.................... Page 1-18
Français...............Pages 19-21
Espanol.............Páginas 22-24
413123
Dresser

ASSEMBLY TOOLS REQUIRED
Hammer
No. 2 Phillips Screwdriver
Tip Shown Actual Size
TABLE OF CONTENTS
Part Identification.......................3
Hardware Identification .............4
Assembly Steps....................5-18
Français..............................19-21
Espanol...............................22-24
Safety .................................25-26
Warranty...................................27
Page 2 www.sauder.com/services 413123
Scissors

PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked
letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help
identify similar parts.
A RIGHT END 1
B LEFT END 1
C UPRIGHT 1
D TOP 1
E BOTTOM 1
F BACK 1
G DOOR 2
H ADJUSTABLE SHELF 1
I SKIRT 1
J LARGE DRAWER FRONT 2
K LARGE DRAWER BACK 2
L LARGE DRAWER SIDE 4
M DRAWER BOTTOM 3
N SMALL DRAWER FRONT 1
O SMALL DRAWER BACK 1
P SMALL DRAWER SIDE 2
Page 3
www.sauder.com/services413123
A
B
C
D
E
F
G
H
I
J
KL
M
N
OP
G
P
M
L

HARDWARE IDENTIFICATION
Screws are shown actual size. You may receive extra hardware with your unit.
Page 4 www.sauder.com/services 413123
AA WARNING LABEL - 1
(Refer to the last step for proper
location and application)
WARNING
!
Serious or fatal crushing injuries can
occur from furniture tip-over. To help
prevent tip-over:
• Place heaviest items in the lowest drawers.
• Unless specifically designed to accommodate, do not
set TVs or other heavy objects on top of this product.
• Never allow children to climb or hang on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
• If equipped with a drawer interlock system, do not
defeat or remove it.
Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over.
This is a permanent label. Do not attempt to remove!
04/10 332296
APPLIQUE CARD - 1
X
METAL BRACKET - 6
T
BLACK 9/16" LARGE HEAD SCREW - 21
FF
BLACK 1-7/8" FLAT HEAD SCREW - 6
BB
METAL PIN - 4
Y
BLACK 1/2" FLAT HEAD SCREW - 28
GG
BLACK 1-1/2” PAN HEAD SCREW - 12
CC
UHINGE - 4
NAIL - 40
HH
PULL - 5
V
EE SILVER 3/4” PAN HEAD SCREW - 12
SILVER 7/8" MACHINE SCREW - 10
DD
SLIDE SET - 3
Q
DRAWER FRONT
BRACKET - 10
W
SHELF SNAP - 4
Z
HIDDEN CAM - 6
RCAM DOWEL - 6 S

Look for this icon. It means a video
assembly tip is available at:
www.sauder.com/services/tips
1
1
S
t
e
p
Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
Push six HIDDEN CAMS (R) into the ENDS (A and B) and UPRIGHT (C). Then, insert the metal end of a CAM DOWEL (S) into
each HIDDEN CAM.
Page 5
www.sauder.com/services413123
Do not tighten the HIDDEN CAMS in this step.
(6 used)
A
B
C
Arrow Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
S
R

2
2
S
t
e
p
Page 6 www.sauder.com/services 413123
NOTE: Before beginning this step, separate the SLIDES from the SLIDE SETS (Q) and the DRAWER PINS at the end of the
SLIDES using a SCISSORS. Save the DRAWER PINS. You will use them in Step 13.
Fasten the SLIDES (Q) to the RIGHT END (A) and UPRIGHT (C). Use twelve SILVER 3/4" PAN HEAD SCREWS (EE) through
the first and last holes in the SLIDES.
NOTE: The SLIDES are marked "RIGHT" and "LEFT" for easy identification. The SLIDES marked "RIGHT" will fasten to the
RIGHT END (A) and the SLIDES marked "LEFT" will fasten to the UPRIGHT (C). There are also arrows on the SLIDES for correct
positioning on the ENDS.
DRAWER PIN
(Save for Step 13) Q
Using your Scissors, separate the
SLIDES and the DRAWER PINS
A
C
SILVER 3/4” PAN HEAD SCREW
(12 used in this step)
EE
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Angled edge
Straight edge
Notch
LEFT SLIDES
RIGHT SLIDES
Q
Q
Q
Q
Q
Q
Finished edge
Finished edge

3
3
S
t
e
p
Page 7
www.sauder.com/services413123
Fasten the UPRIGHT (C) to the TOP (D). Tighten two HIDDEN CAMS.
C
D
Finished edge
Surface with holes
Surface with HIDDEN CAMS
Long finished edge
Caution
Risk of damage or
injury. Hidden Cams
must be completely
tightened. Hidden
Cams that are not
completely tightened
may loosen, and parts
may separate.
To completely tighten:
Start Tighten
Maximum
210 degrees
Arrow
Minimum
190 degrees
Arrow

Fasten the BOTTOM (E) to the UPRIGHT (C). Use two BLACK 1-7/8" FLAT HEAD SCREWS (BB).
Fasten A METAL BRACKET (T) to the TOP (D). Use a BLACK 9/16" LARGE HEAD SCREW (FF).
4
4
S
t
e
p
Page 8 www.sauder.com/services 413123
CD
E
Surface with
more holes
BLACK 9/16" LARGE HEAD SCREW
(1 used for the METAL BRACKET)
FF
BLACK 1-7/8" FLAT HEAD SCREW
(2 used in this step)
BB
These holes
must be here.
T

5
5
S
t
e
p
Page 9
www.sauder.com/services413123
D
EA
B
Fasten the ENDS (A and B) to the TOP (D). Tighten four HIDDEN CAMS.
Fasten the ENDS (A and B) to the BOTTOM (E). Use four BLACK 1-7/8" FLAT HEAD SCREWS (BB).
Finished edge
Finished edge
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
BB
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
Maximum
210 degrees
Minimum
190 degrees
Arrow

6
6
S
t
e
p
Page 10 www.sauder.com/services 413123
Fasten five METAL BRACKETS (T) to the BOTTOM (E) and SKIRT (I). Use five BLACK 9/16” LARGE HEAD SCREWS (FF).
NOTE: Be sure the edges of the METAL BRACKETS are even with the edges of the BOTTOM and SKIRT.
Fasten the SKIRT (I) to the ENDS (A and B) and BOTTOM (E). Use five BLACK 9/16" LARGE HEAD SCREWS (FF).
BLACK 9/16" LARGE HEAD SCREW
(10 used for the METAL BRACKET)
FF
E
A
B
I
I
T
T
T