Sauder Englewood 426908 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-523-3987.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
Enlish p 1-29
Français p 30-34
Español p 35-39
Lot # 543714 06/18/20
Purchased: __________________
Lateral File
Enlewood Collection | Model 426908
Congratulations. You
are now an adult.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
4-5
6-29
30-34
35-39
40-42
43
Adjustable Wrench
426908 www.sauder.com/servicePae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BOTTOM (1)
D550 RIGHT DRAWER SIDE (2)
D551 LEFT DRAWER SIDE (2)
D552 DRAWER BACK (2)
D985 DRAWER BOTTOM (2)
E LARGE BASE (2)
F SMALL BASE (2)
G BACK (2)
H LARGE DRAWER FRONT (1)
J BALLAST (1)
K SMALL DRAWER FRONT (1)
M67 DRAWER BRACE (2)
A
B
C
D
E
F
G
H
J
K
G
E
D550
D550
D551
D551
D552
D552
D985
D985
M67
M67
426908www.sauder.com/service Pae 3

Hardware Identification
34G INTERLOCK MECHANISM - 1 DRAWER
ACTUATOR - 2
62G
31G CORNER BRACKET - 4 LARGE FILE
BRACKET - 2
57G
FILE GLIDE - 4
4B
(EXTENSION SET SHOWN SEPARATED)
EXTENSION RAIL - 4
35MA EXTENSION SLIDE - 4 35MC 10A SLIDE CAM - 4
FILE ROD - 4
9B FILE BAR - 4
14B
SMALL FILE
BRACKET - 2
11B HIDDEN CAM - 6
1F
METAL BRACKET - 6
4G
WOOD DOWEL - 4
15F
CAM DOWEL - 6
2F 36F TWIST-LOCK®FASTENER - 12
76G L - LOCK BRACKET - 1 77G Z - LOCK BRACKET - 1 PULL - 2
189K
LOCK PACK - 1
21J
426908 www.sauder.com/servicePae 4

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 9/16" PAN HEAD SCREW - 3
51S
BLACK 1-1/8" PAN HEAD SCREW - 4
9S
BROWN 7/16" LARGE HEAD SCREW - 4
6S
BLACK 1/2" FLAT HEAD SCREW - 6
11S 30S BLACK 1-9/16" FLAT HEAD SCREW - 10
BLACK 9/16" LARGE HEAD SCREW - 48
1S 3S GOLD 5/16" FLAT HEAD SCREW - 16
426908www.sauder.com/service Pae 5

Hardware Usage Guide
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
2.
Push a TWIST-LOCK® FASTENER
into the large hole in the part.
1.
HOW TO USE A TWIST-LOCK®FASTENER
HOW TO USE A HIDDEN CAM & CAM DOWEL 2. Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
1. Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the ede
of the board.
Hole
Arrow
Metal end
Hidden Cam
Cam Dowel
Start Tighten
Arrow
Minimum
190 derees
Caution
Risk of damae or
injury. HIDDEN CAMS
must be completely
tihtened. HIDDEN
CAMS that are not
completely tihtened
may loosen, and parts
may separate. To
completely tihten:
Arrow
Maximum
210 derees
3.
426908 www.sauder.com/servicePae 6

Step 1 Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å To bein assembly, push four SAUDER TWIST-LOCK®
FASTENERS (36F) into the lare holes in the ENDS (A and B).
A
B
2
36F
Do not tihten the TWIST-LOCK® FASTENERS in this step.
426908www.sauder.com/service Pae 7
Some assembly
(and snacks) required.

å Separate the EXTENSION SLIDES (35MC) from the EXTENSION RAILS (35MA) as shown in the upper diaram below. Be
prepared, the parts are reasy.
å Fasten the EXTENSION RAILS (35MA) to the ENDS (A and B). Use eiht GOLD 5/16" FLAT HEAD SCREWS (3S)
throuh holes #1 and #3.
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlared diaram. Then, slide the inner
cartride of the EXTENSION RAIL in to find the other hole that lines up with the hole in the END. Turn a SCREW into
this hole.
å NOTE: The EXTENSION SLIDES (35MC) will be used later for the DRAWERS.
Step 2
A
B
Push the black lever in and pull the SLIDE from the RAIL.
35MA
35MC
3
2
1
1
2
3
GOLD 5/16" FLAT HEAD SCREW
(8 used for the RAILS)
3S
7
Open end
1
2
3
3
2
1
Open end
426908 www.sauder.com/servicePae 8

å Fasten the INTERLOCK MECHANISM (34G) to the RIGHT END (A).
Use three BLACK 9/16" PAN HEAD SCREWS (51S).
å Fasten the L - LOCK BRACKET (76G) to the RIGHT END (A). Use
two BLACK 9/16" LARGE HEAD SCREWS (1S).
Step 3
A
34G
BLACK 9/16" PAN HEAD SCREW
(3 used in this step)
51S
BLACK 9/16" LARGE HEAD SCREW
(2 used in this step)
1S
426908www.sauder.com/service Pae 9

å To bein assembly, push eiht SAUDER TWIST-LOCK®
FASTENERS (36F) into the lare holes in the BACKS (G).
Step 4
G
G
2
36F
Do not tihten the TWIST-LOCK® FASTENERS in this step.
36F
426908 www.sauder.com/servicePae 10

å Fasten the RIGHT END (A) to the BACKS (G). Tihten four
TWIST-LOCK® FASTENERS.
Step 5
A
G
G
Unfinished ede
Unfinished ede
2
Open end
426908www.sauder.com/service Pae 11

å Push four HIDDEN CAMS (1F) into the BOTTOM (D). Then,
insert the metal end of a CAM DOWEL (2F) into each
HIDDEN CAM.
Step 6
D
1
Do not tihten the HIDDEN CAMS in this step.
1F
2F
Arrow
Metal end
1F
2F
Metal end
Arrow
426908 www.sauder.com/servicePae 12

å Fasten the BOTTOM (D) to the RIGHT END (A).
Tihten two HIDDEN CAMS.
Step 7
D
A
These edes must be even.
Surface with HIDDEN CAMS
1
426908www.sauder.com/service Pae 13

å Fasten the LEFT END (B) to the BOTTOM (D) and BACKS (G). Tihten
two HIDDEN CAMS and tihten four TWIST-LOCK® FASTENERS.
Step 8
B
G
G
D
2
1
Open end
426908 www.sauder.com/servicePae 14
1
2

å Insert four WOOD DOWELS (15F) into the ENDS (A and B).
å Fasten the TOP (C) to the ENDS (A and B). Tihten four
TWIST-LOCK® FASTENERS.
å NOTE: Be sure the WOOD DOWELS in the ENDS insert
into the TOP.
Step 9
B
A
C
15F
15F
2
426908www.sauder.com/service Pae 15

å Carefully turn your unit onto its top.
å Fasten the CORNER BRACKETS (31G) to the BOTTOM (D).
Use eiht BLACK 9/16" LARGE HEAD SCREWS (1S).
Step 10
D
31G
31G
31G
31G
BLACK 9/16" LARGE HEAD SCREW
(8 used in this step)
1S
426908 www.sauder.com/servicePae 16

å Fasten six METAL BRACKETS (4G) to the
BASES (E and F). Use six BLACK 9/16"
LARGE HEAD SCREWS (1S).
å NOTE: Be sure the BRACKETS are even with the edes of
the BASES.
Step 11
E
E
F
F
4G
BLACK 9/16" LARGE HEAD SCREW
(6 used in this step)
1S
426908www.sauder.com/service Pae 17

å Fasten SMALL BASES (F) to the BOTTOM (D). Use eiht
BLACK 9/16" LARGE HEAD SCREWS (1S) throuh the
CORNER BRACKETS on the BOTTOM and into the holes
in the SMALL BASES.
å Fasten the BOTTOM (D) to the METAL BRACKETS on
the SMALL BASES (F). Use two BLACK 9/16" LARGE
HEAD SCREWS (1S).
Step 12
F
F
D
BLACK 9/16" LARGE HEAD SCREW
(10 used in this step)
1S
426908 www.sauder.com/servicePae 18

å Fasten LARGE BASES (E) to the BOTTOM (D). Use eiht
BLACK 9/16" LARGE HEAD SCREWS (1S) throuh the
CORNER BRACKETS on the BOTTOM and into the holes
in the LARGE BASES.
å Fasten the BOTTOM (D) to the METAL BRACKETS on
the LARGE BASES (E). Use four BLACK 9/16" LARGE
HEAD SCREWS (1S).
Step 13
D
E
E
BLACK 9/16" LARGE HEAD SCREW
(12 used in this step)
1S
426908www.sauder.com/service Pae 19
Now miht be a
ood time to refresh
your drink.

å Fasten the BALLAST (J) to the BOTTOM (D). Use four
BLACK 1-1/8" PAN HEAD SCREWS (9S).
Step 14
J
D
9S
BLACK 1-1/8" PAN HEAD SCREW
(4 used in this step)
426908 www.sauder.com/servicePae 20