Screen Technics CINEMASNAP XL User manual
I
N
A
U
S
T
R
A
L
I
A
P
R
O
U
D
L
Y
B
U
I
L
T
1
Continued Over.../
INSTRUCTIONS - CINEMASNAP XL FIXED FRAME PROJECTION SCREEN
Thank you for purchasing a Screen Technics Projection Screen, please
ensure that you read the following instructions fully before attempting to
install this product.
STEP 1. Layout all components ready for assembly as
shown
Note: Box Section Frame will be supplied
STEP 2. Push the four corners of the frame together.
Due to frame size, you may need to join frame pieces,
you may need to use a plastic or wooden mallet (not
metallic) to achieve this result.
STEP 4A. Place corner brackets in each corner of frame
(as shown)
STEP 5. It is now time to install the L-Shaped brackets and there are two options:
• The brackets come supplied with self-tapping (Tek) screws that allow you to drill directly
into the frame, anywhere that best suits wall stud supports and the like. Later on in the
installation you will need enough room to re-screw these Tek screws top and bottom of the
frame for nal xing.
• If you don’t have enough “elbow” room to get at the top of frame with a power or screw
driver at this latter time because of a low ceiling then utilize the nylon bushes supplied
with the small Allen-Key bolt and x one each to the two top L-Brackets and use the two
locating holes on the top of the frame, although this restricts bracket positioning it allows
you to simply insert the bushes into the holes and then x the bottom brackets by screws
and your done.
Larger Wall Brackets supplied with XL version
STEP 3. With the Hex Head Allen-Key screws use the
provided Allen-Key to screw tight all four corners. You
must ensure each of the four corners are square and
there are no large gaps obvious before you start to
insert Hex head Allen-Key screw, otherwise jamming
may occur.
Note: Box Section Frame will be supplied
STEP 4. Tighten all internal Allen-Key screws (one on
each corner as shown below), before fully tightening
the external screws.
Note: Box Section Frame will be supplied
CINEMASNAP 235
CINEMASNAP 235
3
Step 4A Place corner brackets in each corner of frame (as shown below)
Step 5. It is now time to install the L-Shaped brackets and there are two options:
•The brackets come supplied with self-tapping (Tek) screws that allow you to drill directly
into the frame, anywhere that best suits wall stud supports and the like. Later on in the
installation you will need enough room to re-screw these Tek screws top and bottom of
the frame for final fixing.
•If you don’t have enough “elbow” room to get at the top of frame with a power or screw
driver at this latter time because of a low ceiling then utilize the nylon bushes supplied
with the small Allen-Key bolt and fix one each to the two top L-Brackets and use the two
locating holes on the top of the frame, although this restricts bracket positioning it
allows you to simply insert the bushes into the holes and then fix the bottom brackets
by screws and your done.
8 x Larger Wall Brackets supplied with XL version
CINEMASNAP 235
3
Step 4A Place corner brackets in each corner of frame (as shown below)
Step 5. It is now time to install the L-Shaped brackets and there are two options:
•The brackets come supplied with self-tapping (Tek) screws that allow you to drill directly
into the frame, anywhere that best suits wall stud supports and the like. Later on in the
installation you will need enough room to re-screw these Tek screws top and bottom of
the frame for final fixing.
•If you don’t have enough “elbow” room to get at the top of frame with a power or screw
driver at this latter time because of a low ceiling then utilize the nylon bushes supplied
with the small Allen-Key bolt and fix one each to the two top L-Brackets and use the two
locating holes on the top of the frame, although this restricts bracket positioning it
allows you to simply insert the bushes into the holes and then fix the bottom brackets
by screws and your done.
8 x Larger Wall Brackets supplied with XL version
3
Step 4A Place corner brackets in each corner of frame (as shown below)
Step 5. It is now time to install the L-Shaped brackets and there are two options:
•The brackets come supplied with self-tapping (Tek) screws that allow you to drill directly
into the frame, anywhere that best suits wall stud supports and the like. Later on in the
installation you will need enough room to re-screw these Tek screws top and bottom of
the frame for final fixing.
•If you don’t have enough “elbow” room to get at the top of frame with a power or screw
driver at this latter time because of a low ceiling then utilize the nylon bushes supplied
with the small Allen-Key bolt and fix one each to the two top L-Brackets and use the two
locating holes on the top of the frame, although this restricts bracket positioning it
allows you to simply insert the bushes into the holes and then fix the bottom brackets
by screws and your done.
8 x Larger Wall Brackets supplied with XL version
CINEMASNAP 235
info@screentechnics.com.au
screentechnics.com.au
AUSTRALIA
22-24 Suttor Road, Moss Vale NSW 2577
+61 2 4869 2100
NEW ZEALAND
44 Mahana Road, Te Rapa, Hamilton
0800 022 821
I
N
A
U
S
T
R
A
L
I
A
P
R
O
U
D
L
Y
B
U
I
L
T
ESTABLISHED IN 1990
I
N
A
U
S
T
R
A
L
I
A
P
R
O
U
D
L
Y
B
U
I
L
T
2
STEP 6. Attach brackets as shown – Utilizing nylon
bushes and locating holes only if necessary as
explained in previous step.
STEP 7. With all four brackets attached, place screen
frame (not with surface) on the wall and mark holes.
STEP 8. Use wall mates or plugs to attach frame if no
wall studs are present and ensure that you have a
secure xing method for a safe installation.
STEP 9. Remove frame from the wall by undoing outside
bracket screws - Brackets are to remain on wall.
•
•
•
•
PREPARE SCREEN SURFACE
Please do not allow the steel rods to come into contact with the screen surface viewing area as it
may cause damage.
STEP 10. Place a drop sheet on the oor to protect the
front of the projection surface.
Slide all four steel rods into the sleeve surrounding the
screen surface.
Note: Make sure that rods are even in the screen
sleeve and not overlapping on the corners.
STEP 11. Once all four rods have been placed into the
screen sleeve, attach the screen surface to the frame
as shown below - ensuring to work the screen surface
evenly to all four sides.
This will require minimum two people to complete and
will require quite a bit of force to stretch the surface
onto the XL frame.
Attach surface at top centre and stretch and attach at
bottom centre then stretch and attach to left and right
centre.
Then progressively attach surface on all four sides
moving from centre point towards the corners.
STEP 12. Now install spreader bars, you will nd the aluminium blocks inserted in the frame on
the vertical and horizontal frame pieces to attach the bars.
Install the vertical spreader bars rst, due to the force of the projection surface
you will see a bow in the top and bottom of the frame, you will need to pull the
frame apart to install the vertical spreader bars, then install the horizontal
spreader bars
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
INSTRUCTIONS - CINEMASNAP XL FIXED FRAME PROJECTION SCREEN
•
•
5
Step 8. Use appropriate fixings to attach frame if no wall studs are present and ensure
that you have a secure fixing method for a safe installation.
Step 9. Remove frame from the wall by undoing outside bracket screws - Brackets are
to remain on wall.
Example of vertical
and horizontal
spreader bars
Depending on the
size and height of
CinemaSnap frame -
Number of spreader
bars with change
Continued Over.../
I
N
A
U
S
T
R
A
L
I
A
P
R
O
U
D
L
Y
B
U
I
L
T
3
Example of Horizontal Spreader Bar Mounting
Example of Vertical
Spreader Bar Mounting
Vertical Spreader Bars are
screwed to the horizontal
spreader bars
as shown above using
supplied (TEK) screws
Horizontal Spreader Bars are screwed to frame top and bottom
as shown above using supplied (TEK) screws
STEP 13. Attach the screen to the brackets on wall – Wipe down screen frame of any
ngerprints and dust off the screen surface.
Please follow these instructions to ensure trouble free operation;
• Cleaning of the screen is best achieved by rst dusting the surface with a feather duster,
then to remove any stubborn marks, use a small amount of mild detergent and warm water
on a clean white lint free cloth. It is most important that you only treat the actual mark by
this process and not the entire surface.
• Do not use any abrasive cleanser as this will damage the surface.
Should you have any questions regarding the installation of our projection screens please call our
technical sales desk on +61 2 4869 2100 for assistance.
INSTRUCTIONS - CINEMASNAP XL FIXED FRAME PROJECTION SCREEN
8
Example of Horizontal Spreader Bar Mounting
Horizontal Spreader Bars are screwed to frame top and bottom
as shown above using supplied (TEK) screws
Example of Vertical Spreader Bar Mounting
Vertical Spreader Bars are screwed to the horizontal spreader bars
as shown above using supplied (TEK) screws
8
Example of Horizontal Spreader Bar Mounting
Horizontal Spreader Bars are screwed to frame top and bottom
as shown above using supplied (TEK) screws
Example of Vertical Spreader Bar Mounting
Vertical Spreader Bars are screwed to the horizontal spreader bars
as shown above using supplied (TEK) screws
Other Screen Technics Projection Screen manuals
Screen Technics
Screen Technics ELECTRICINEMA User manual
Screen Technics
Screen Technics CINEMATECH User manual
Screen Technics
Screen Technics ELECTRICINEMA User manual
Screen Technics
Screen Technics ELECTRICINEMA A User manual
Screen Technics
Screen Technics ELECTRICINEMA User manual
Screen Technics
Screen Technics ELECTRICINEMA 235 User manual
Screen Technics
Screen Technics ViewMaster Pro User manual
Screen Technics
Screen Technics ELECTRICINEMA User manual
Screen Technics
Screen Technics MASTERFIT IP User manual
Screen Technics
Screen Technics TRAPDOOR User manual
Popular Projection Screen manuals by other brands
Vivo
Vivo PS-M-100G instruction manual
Kerchan
Kerchan KERSAD2022012 Product specification
Changhong Electric
Changhong Electric S-CK Series user guide
Liberty
Liberty Grandview Skyshow D Series user manual
Elite Screens
Elite Screens QuickStand Drape Series Product White Paper
Mustang
Mustang SC-E120D169 Specifications
Screen Research
Screen Research MS2-IT installation manual
Draper
Draper Access XL Installation & operating instructions
displayit
displayit Elements General assembly instructions
Draper
Draper Envoy Installation & operating instructions
Da-Lite
Da-Lite Whiteboard Mount Instruction book
Classic Exhibits
Classic Exhibits Perfect 10 VK-1400 manual