Screen Technics ELECTRICINEMA User manual

1
ElectriCinema with IR Remote Control &
Installation Instructions
Thank you for purchasing a Screen Technics Projection Screen, please ensure that you
read the following instructions fully before attempting to install this product.
Before you Install Screen
Once you have unpacked the screen from the box, lay the canister on the ground and
carefully remove the black tape holding the screen surface in place – once the surface is
freed from the canister, take the bottom slat rod, which is taped to the canister, and insert it
into the bottom end corner of the screen until it is all the way inserted into the pocket, as
illustrated below. Then install the screen as described to follow.
Wall Mounting Instructions
1. Measure the wall where the screen is to be installed and mark with a pencil the
desired height to top of screen case and also the centre of the screen.

2
2. Measure the length of screen canister along the top surface and mark the centre
of the canister with a pencil, to assist in lining up the screen when mounting.
3. Determine the best positions for the wall brackets, allowing that in Gyprock or in
low strength walls the brackets will be screwed into a timber stud. In more solid
walls, such as masonry, position the brackets approx 150mm in from the canister
end. The brackets should be no more than 450mm in from each end. You must
use a minimum of 3 off wood screws per bracket or 2 off Dyna-bolts, for masonry
walls and you must be satisfied that the attachment is strong enough for the a
safe installation.
NB: Top of bracket
equals top of screen canister.

3
4. You may need to remove the bottom clip in order to screw brackets to wall,
please ensure to replace them afterwards.
5. Using two people install the screen by placing the screen canister into the bottom
of the bracket clips and pivoting back the canister to slot the top pins into the T
channels running along the top of the canister (you may have to remove any tape
that is in the way).

4
6. Holding screen in position tighten up Allen screw at each end and check that the
top pins have hooked into the T section of the screen canister.
7. See Page 5 electrical connection information.
Ceiling Mount Instructions
Below is a photo showing a side view using the brackets for ceiling fixing, you would
follow the instructions for the wall mounting system, with the only difference being
the screen is mounted hard against the ceiling. It is important that adequate support
is supplied by the ceiling structure to support the screen and to ensure a safe
installation. Never rely just on the Gyprock for attachment.

5
Please follow these instructions to ensure trouble free operation;
• Ensure that the screen is free to descend and that any adhesive tape that has been
placed on the bottom of the screen (to stop movement during transport) has been
removed.
• When installed, the opening in the canister should be down and at the back of the
canister. This will put the motor on the left-hand side of the screen, as viewed by the
audience.
• Cleaning of the screen is best achieved by first dusting the surface with a feather
duster, then to remove any stubborn marks, use a small amount of mild detergent
and warm water on a clean white lint free cloth. Do not use a saturated cloth, as this
may leave a watermark, only a damp one. It is most important that you only treat the
actual mark by this process and not the entire surface.
• The screen comes complete with a IR transmitter and 3-pin plug already attached to
the flex leaving the screen. After installation and turning the power on to the screen
the screen is ready to go, once you have placed and connected the IR Sensor unit
which plugs into the Data cable that exits the canister.
Please note: It adjust the up and down limit positions on ElectriCinema IR Projection
Screens you require an ILT Limit Setting Tool to make adjustments – see price list for
details.
 The Motor is 240 V 50Hz and draws 1.2 A.
 The screen drop is set and tested at the factory. Therefore, any damage caused to the
screen from limit re-adjustment is not covered by warranty.
Should you have any questions regarding the installation of our projection screens please
call our technical sales desk on 02 4869 2100 for assistance.
Cnr Vale & Suttor Roads
Moss Vale
NSW 2577
PH – 02 4869 2100
Fax – 02 4869 2123
Thinking Screens… Think Screen Technics