SDC Z7200 User manual

Any suggestions or comments to this instruction or
product are welcome. Please contact us through
our website or email [e-mail]
P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSET\INST-Z7200 Rev M 08-21 Page 1
Z7200
CYLINDRICAL LOCK
FOR USE ON DOORS 1-3/8” ~ 2" (35mm ~ 51mm) THICK
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
INSTALLATION INSTRUCTIONS
1. MARK DOOR 2. DRILL HOLES
a. Mark centerline on door face and door edge
(usually 38" from finished floor)
b. Select backset 2-3/8” or 2-3/4” and mark hole
center on door face
NOTE: BACKSET ON DOOR FACE MUST BE
THE SAME AS BACKSET OF YOUR
LOCK.
c. Mark two holes for screw post.
2-1/8” (54mm)
Hole for lockset
5/16” (8mm) hole for
screw post
a
b
c
1" or 31/32"
(24.6mm or 25.4mm)
hole for latch
Fold template for High or
Low Bevel positioning
(reference template)
OPTIONAL:
DOOR CORE DRILLING GUIDE #7000-DG &
CORING DRILL BIT #7000-DB
TOOLS REQUIRED FOR NEW INSTALLATION:
1 philips head screwdriver 1 2-1/8” (54MM) hole saw
1 1" (25.4mm) drill bit 1 5/16” (8mm) drill bit
1 chisel 1 file
LATCH
LOCK BODY
ASSEMBLY OUTSIDE
MOUNTING
PLATE
OUTSIDE
ROSE
OUTSIDE
LEVER
INSIDE
LEVER
LEVER
CATCH
TOOL
INSIDE
ROSE w/LINER
INSIDE MOUNTING
PLATE

5. REMOVE INSIDE TRIM
INSIDE LEVER
INSIDE ROSE
LINER
LEVER CATCH
TOOL
OUTSIDE LEVER
ASSEMBLY
INSIDE MOUNTING
PLATE
ROSE
Use lever catch tool to depress lever
catch, visible under hole of inside lever
shank and slide off inside lever, rose
liner and mounting plate.
P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSET\INST-Z7200 Rev M 08-21 Page 2
a. Insert latch in hole and keep it parallel to door face.
Mark outline and remove latch
b. Chisel 1/8” (3mm) deep or until faceplate is flush with
door edge.
c. Insert latch and tighten screws.
NOTE: LATCH BOLT BEVEL MUST FACE TOWARDS
CLOSING DIRECTION.
a. Close door to mark horizontal line of strike.
b. Measure one half of door thickness from
door stop to mark vertical center line of strike.
Drill 1" (25.4mm) hole, 1/2” (12.7mm) deep at
intersection of horizontal and vertical center lines.
c. Cut out jamb 3/32” (2.4mm) deep or until strike
is flush with jamb. Tighten screws securely.
c
a
b
a
b
CENTER
LINE
1" (25.4mm) hole
1/2” (12.7mm) deep
c
4. INSTALL STRIKE3. INSTALL LATCH
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011

6. ADJUST DOOR THICKNESS 7. INSTALL OUTSIDE LEVER ASSEMBLY
Install outside lever assembly on the door. Make sure tail
of latch is engaging with retractor correctly as illustrated.
Refer to wire diagram on last page for wiring.
9. INSTALL LEVER
a. Depress lever catch with tool provided.
Push inside lever on completely until
catch engages in lever.
Confirm lever is secured.
INSIDE
LEVER
INSIDE
ROSE
1-3/4" thick
Door thickness : 2" thick
1-3/8" thick
P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSET\INST-Z7200 Rev M 08-21 Page 3
LOCK BODY
ASSEMBLY
LATCH
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
INSIDE
MOUNTING
PLATE
MOUNTING
SCREWS
INSIDE
ROSE
ROSE
LINER
b. Press inside rose
onto mounting plate
and tighten screws securely.
a. Install inside mounting plate to lock body.
8. INSTALL INSIDE MOUNTING PLATE
AND ROSE

LATCH STATUS MECHANICAL SWITCH SPDT
3A @ 30VDC
WIRE DIAGRAM
Flat (No Bevel)
5/32" (4mm)
1-3/4” Door
1-5/8"
(41mm)
1/8" (3mm)
Holes
2-3/8" (60mm) BACKSET
MARK CENTER OF
2-1/8” (54mm)
HOLE ON DOOR FACE
2-3/4” (70mm) BACKSET (FOR METAL
DOORS ONLY)
DOOR EDGE
2X 5/16" (8mm)
hole
High Bevel
Low Bevel
1" (25mm)
Hole
2-3/4”
(70mm)
2-15/32" (62.7mm) (FOR METAL
DOORS ONLY)
DO NOT USE AS A PHYSICAL TEMPLATE. THIS LAYOUT
IS INTENDED AS A DIMENSIONAL REFERENCE ONLY.
USE THE TEMPLATE PACKAGED WITH THE LOCK
LAYOUT
Using the PR-7200 limits the power consumption, reduces operating temperature, and suppresses inductive
kickback. (The PR-7200 is only supplied with the Fail-Safe models.)
COM = WHT/RED
N/C = ORG/RED
N/O = YEL/RED
LATCH STATUS
P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSET\INST-Z7200 Rev M 08-21 Page 4
RED
BLK
WHT
BLU
RED(+)
WHT(-)
LOCKSET PR-7200
POWER REGULATOR
BLU
WHT
TO PWR
SUPPLY
RED (+)
BLK (-)
12vdc @ INRUSH: .6A
HOLDING: .25A
RED(+)
WHT(-)
RED
BLK
WHT
BLU
LOCKSET PR-7200
POWER REGULATOR
BLU
WHT TO PWR
SUPPLY
RED (+)
BLK (-)
24vdc @ INRUSH: .3A
HOLDING: .15A
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
COM = GREY
N/C = YELLOW
N/O = ORANGE
REX
REQUEST-TO-EXIT MAGNETIC SENSOR
200mA @ 30VAC (RESISTIVE)
*Both options cant be used
simultaneously.