SDC Z7835 Series User manual

Any suggestions or comments to this instruction or
product are welcome. Please contact us through
our website or email eng[email protected]
A. Door Preparation:
1. Measure desired height from finished floor, mark a horizontal line on door and door edge.
2. Align template on edge of door with applicable horizontal at height line. Check the chart for drilling trim
holes on template and mark only holes for lock function being installed.
3. Mortise door edge according to measurements on
installation template and drill proper holes for trim.
4. Recess for face plate, the dimension is:
L 8-1/32" x W 1-5/16" x D 7/32".
Height line
of lever
or knob
C
L
7/32"
INSTALLATION INSTRUCTIONS
12VDC Z7835 SERIES MORTISE LOCK
of cylinder
of lockcase
of lever
or knob
Vertical centerline
C
Installation
template
C
L
C
L
C
L
Lof
door edge
OPTIONAL
DOOR CORE DRILLING GUIDE
#7000-DG
P:\INSTALLATION INST\Electrified Lockset\INST-Z7835-E (12VDC) REV B 11-17 Page 1
801 Avenida Acaso, Camarillo, Ca. 93041 • [phone] • Fax: [phone]
www.sdcsecurity.com • E-mail: [email protected]

B. Strike Installation:
1. Align strike template on jamb. Be sure to keep 3/8" distance between lock centerline and strike
centerline. Recess 5/32" for flush fit of strike and dust box.
2. Mortise jamb according to measurement of strike template. Then fit strike and dust box into frame
and secure into place with supplied screws.
4-7/8"
3-17/32"
C
L
Strike
Lock C
L
3/8"
3/8"
1" Holes
1-1/8" Deep
C
L
Jamb
Pull out and turn
1. Change latchbolt handing
If the hand of the latchbolt doesn’t match the door hand, remove the fixing screw and pull the latchbolt out from
lock case. Turn the latchbolt 180 ° to change the handling. Position latchbolt back, into case and fasten it.
Instructions for changing latchbolt handing:
C. Install Lockcase
Remove screw
P:\INSTALLATION INST\Electrified Lockset\INST-Z7835 (12VDC) REV B 11-17 Page 2

P:\INSTALLATION INST\Electrified Lockset\INST-Z7835 (12VDC) REV B 11-17 Page 3
3. Connect wires as shown on the lock cover diagram.
4. Insert lockcase into mortise cut-out and fasten screws to door.
1. Insert spindles as shown
E. Install Lever trim
1. Place the reversible spring cage onto the ferrules with arrow pointing in direction of lever rotation.
2. Install outside trim with mounting posts through door and position lever onto the spindle.
3. Install inside spring cage onto the spindle with the arrow pointing in the direction of inside lever rotation.
4. Install inside mounting plate onto spindle. Tighten with provided screw.
5. Cap inside rose over mounting plate.
D. Install Spindles
C. Install Lockcase (Continued)
Reversible spring cage
Ferrule
Mounting post
Into Mounting post

1. Screw cylinder into threaded hole of lock case.
2. Tighten the setting screw against cylinder(s) by turning clockwise as shown.
3. Install face plate onto lock case front and fasten with supplied screws.
F. Install Cylinder and Armor Face Plate
USE THIS CAM.
P:\INSTALLATION INST\Electrified Lockset\INST-Z7835 (12VDC) REV B 11-17 Page 4
E. Install Lever trim (continued)
6. Screw inside lever into position and tighten lever collar with supplied spanner wrench.
spanner wrench.
Spanner wrench

P:\INSTALLATION INST\Electrified Lockset\INST-Z7835 (12VDC) REV B 11-17 Page 5
INSTALLATION WIRE DIAGRAM
Model Z7835 Series 12VDC ONLY
STANDARD WIRING
(NO OPTIONS)
12VDC
+
-
BLK INSIDE
RED OUTSIDE
WHT
NOT USED
+
4 PIN
CONECTOR
WIRING WITH OPTIONS
GREEN COM
DPS BLACK N/C
WHITE N/O
ORANGE COM
REX BROWN N/C
YELLOW N/O
RED/YELLOW COM
LLS RED/BLACK SECURE
RED/GREEN UNSECURE
VIOLET (+) OUTSIDE SOLENOID
SOLENOID GREY (-) OUT/INSIDE SOLENOID
PINK (+) INSIDE SOLENOID
NOT
USED
MOV*
*Install MOV across each coil to protect ACS electronics.
Install as close as possible to the lock
MOV*
*Install MOV across each coil to protect ACS electronics.
Install as close as possible to the lock